D-110-00

SPECIFICATION CONTROL DRAWING MATERIALS 1. INSULATION SLEEVE: Heat-shrinkable, transparent blue, radiation cross-linked modified polyvinylidene fluoride. 2. SOLDER PREFORM WITH FLUX: SOLDER: TYPE Sn63 per ANSI J-STD-006. FLUX: TYPE ROL1 per ANSI-J-STD-004. APPLICATION 1. Part will recover to 0.76 (0.03) . 2. This part is designed to meet the requirements as shown below when tested to Raychem Specification RT-1404. QUALIFICATION TEST ASSEMBLIES The test configuration shall be a follow-through splice made by connecting two wires having 26 AWG tin or silver plated conductors and insulations rated for at least 125°C. REQUIREMENTS: Temperature Rating Voltage Drop** Tensile Strength* Vibration** Temperature Cycling** Current Cycling** Heat Aging* Fluid Resistance* Corrosion Resistance* Corrosive Effect* 150°C Initial 25 millivolts max. 7 lbs. min. MIL-STD-202, Method 204, Condition D Voltage Drop after Vibration - 32 millivolts max. -63±3°C to 150±3°C, 5 cycles (Condition C) Voltage Drop after Cycling - 32 millivolts max. Voltage Drop after Cycling - 32 millivolts max. 120±2 hours at 200±3°C. 20 hours at 25±3°C in fluids of MIL-H-5606, MIL-I-7808, and MIL-L-9236. 96 hours at 35±3°C (Condition A). Voltage Drop after test - 32 millivolts max 16 hours at 121±2°C, Non-corrosive * For test procedures, see Raychem Specification RT1404. ** For test procedures, see page 2. DEVICES 300 Constitution Drive Menlo Park, CA 94025, USA UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. INCHES DIMENSIONS ARE BETWEEN BRACKETS. Raychem reserves the right to amend this ANGLES: N/A TOLERANCES: drawing at any time. Users should evaluate 0.00 N/A the suitability of the product for their ROUGHNESS IN 0.0 N/A application. MICRON 0 N/A TITLE: SOLDERSLEEVE 1.47 (0.058) I.D. MINIATURE DOCUMENT NO.: D-110-00 DCR NUMBER: REPLACES: D000141 DRAWN BY: DATE: PROD. REV.: DOC ISSUE: M. FORONDA 22-Mar-00 P 1 If this document is printed it becomes uncontrolled. Check for the latest revision. SCALE: None n/a SIZE: A SHEET: 1 of 2 SPECIFICATION CONTROL DRAWING TEST PROCEDURES: Voltage Drop: As outlined in RT-1404 with these exceptions: Shall be measured with a 3.0 amp current imposed on splice. Measured over a two inch length which includes the splice. Vibration: Splices shall be mounted so that the center of the splice is 152.4±12.7 (6.0±0.5) from the vibrating member. The splice shall then be vibrated as indicated. One axis of vibration shall be parallel to the splices wires. Upon completion, the voltage drop shall be measured as outlined above. Current Cycling: Three foot lengths of wire shall be spliced and subjected to 50 current cycles. Each cycle shall consist of 30 minutes at 3.75 amperes, followed by 15 minutes at no lead. Voltage drop shall be measures as outlined above. DEVICES 300 Constitution Drive Menlo Park, CA 94025, USA UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. INCHES DIMENSIONS ARE BETWEEN BRACKETS. Raychem reserves the right to amend this ANGLES: N/A TOLERANCES: drawing at any time. Users should evaluate 0.00 N/A the suitability of the product for their ROUGHNESS IN 0.0 N/A application. MICRON 0 N/A TITLE: SOLDERSLEEVE 1.47 (0.058) I.D. MINIATURE DOCUMENT NO.: D-110-00 DCR NUMBER: REPLACES: D000141 DRAWN BY: DATE: PROD. REV.: DOC ISSUE: M. FORONDA 22-Mar-00 P 1 If this document is printed it becomes uncontrolled. Check for the latest revision. SCALE: None n/a SIZE: A SHEET: 2 of 2