DP86-100D

te.com DP86 Differential Pressure Sensor SPECIFICATIONS    316L SS Wet/Wet Differential Low Pressure The DP86 differential pressure sensor is a double-sided, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing designed for O-ring mounting applications. The sensing package utilizes silicone oil to transfer pressure from the two 316L stainless steel diaphragms to a single sensing element. Features      O-Ring Mount Up to -40ºC to +125ºC Operating Range Up to ±0.1% Pressure Non-Linearity Solid State Reliability Low Pressure The DP86 is designed for high performance, low pressure applications where differential pressure measurement is required. The stainless steel package makes it suitable for use in liquids and corrosive environments. Please refer to the DP86 uncompensated, non-silicone oil, constant current and constant voltage (fittings and cable design) for more information on different features of the DP86. Applications      Level Controls Tank Level Measurement OEM Equipment Corrosive Fluids and Gas Measurement Systems Flow Measurements CLICK HERE › CONNECT WITH A SPECIALIST TE CONNECTIVITY SENSORS /// DP86 REVA7 02/2021 Page 1 DP86 Differential Pressure Sensor Specifications Unless otherwise specified, Supply Current: 1.5mA; Ambient Temperature: 25°C 001PSI ≥015PSI 005PSI PARAMETERS MIN TYP UNITS NOTES MAX MIN TYP MAX MIN TYP MAX Sensitivity 9.0 20.0 12.5 19.5 26.5 13.2 20 26.5 Zero Pressure Output -4.0 8.0 -6.0 8.0 -6.0 8.0 mV/V 1 Pressure Non-Linearity -0.30 0.30 -0.20 0.20 -0.10 0.10 %Span 2 Pressure Hysteresis -0.10 0.10 -0.10 0.10 -0.05 0.05 %Span Input/Output Resistance 4.4 Temp. Coefficient – Span -3150 2450 Temp. Coefficient – Resistance 2600 3200 Thermal Hysteresis – Span Thermal Hysteresis – Offset mV/V@FS 6.2 3.8 4.4 5.8 3.8 4.4 5.8 kΩ -2150 -1650 -1250 -1000 -1450 -1250 -1000 ppm/°C 3 3500 1300 1510 1750 1300 1510 -0.25 0.25 -0.25 0.25 -0.25 0.25 -0.25 0.25 Temp. Coefficient – Offset 1 Line (Common Mode) Pressure 1 1000 Line Pressure Effect on Zero 1 µV/V/°C 3 1750 ppm/°C 3 -0.25 0.25 %Span 3 -0.25 0.25 %Span 3 1000 1000 psi 0.8 0.5 3.0 %Span/1kpsi %Span/175psi Pressure Overload 10X 3X 3X Rated 4 Pressure Burst 12X 4X 4X Rated 5 Operating Temperature -40 +85 -40 +125 -40 +125 ºC 6 Storage Temperature -40 +125 -40 +125 -40 +125 ºC 6 20 g Vibration (10~2000Hz) 20 Insulation Resistance (50VDC) 50 Output Load Resistance 5 Supply Voltage 20 50 50 5 5.0 12.0 5 5.0 9.5 5 9.5 MΩ 7 MΩ 8 V Supply Current 2.0 1.5 1.5 mA Voltage Breakdown 500 500 500 VRMS Endurance (FS @ 25°C) Media Compatibility – Pressure Port 1,000,000 9 Cycles All fluids and gases compatible with 316L Stainless Steel & Nitrile Notes 1. Measured at ambient pressure. 2. Best fit straight line 3. Over the temperature range -20°C to +85°C (0°C to 50°C for 1psi, 0°C to 70°C for 5psi) with respect to 25°C. 4. For high-end port, rated or 1000psi whichever is less; for low-end port, rated or 150psi whichever is less. The maximum pressure that can be applied without changing the transducer’s performance or accuracy. 5. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer. 6. Temperature range for cable and connector is -20°C to +105°C. 7. Between case and sensing element. 8. Load resistance to reduce measurement errors due to output loading. 9. At dry air. 10. Direct mechanical contact with diaphragm is prohibited. Diaphragm surface must remain free of defects (scratches, punctures, fingerprints, etc.) for device to operate properly. Caution is advised when handling parts with exposed diaphragms. Use protective cap whenever devices are not in use. 11. Shipping: The Stainless Steel diaphragm is protected by a static dissipative cap, each unit is packaged individually in a 2.5” plastic vial with antistatic foam, cable assembly included in vial. 12. Marking: Device is identified with model number with Pressure Range, Type, Lot Number, Serial Number and Date Code. TE CONNECTIVITY SENSORS /// DP86 REVA7 02/2021 Page 2 DP86 Differential Pressure Sensor Dimensions TE CONNECTIVITY SENSORS /// DP86 REVA7 02/2021 Page 3 DP86 Differential Pressure Sensor Compensation Schematic (Sensors can be compensated using the schematic to get improved performance. A calibration data sheet is included with each unit that provides measured values along with resistor values that will achieve the calculated compensated performance. Ordering Information Part Number DP86 - 030D Pressure Range [PSI] 001 1 PSI 005 5 PSI 015 15 PSI 030 30 PSI 050 50 PSI 100 100 PSI 300 300 PSI 500 500 PSI Pressure Type D Differential CLICK HERE › CONNECT WITH A SPECIALIST NORTH AMERICA Tel +1 800 522 6752 EUROPE Tel +31 73 624 6999 ASIA Tel +86 0400 820 6015 te.com/sensors TE Connectivity, TE, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2021 TE Connectivity Corporation. All Rights Reserved. Version A7 02/2021 TE CONNECTIVITY SENSORS /// DP86 REVA7 02/2021 Page 4