DWP-125-1/2-KIT3-REFILL

DWP-125 Flexible, flame-retardant, adhesive-lined, polyolefin heat-shrinkable tubing Adhesive-lined, medium-wall DWP-125 heat-shrinkable tubing is a versatile, environmentally friendly choice for many commercial applications that require mechanical protection and sealing against moisture and chemical ingress. industries such as appliance and satellite communication. DWP-125 tubing has an outer jacket of radiation-crosslinked, flexible, flame-retardant polyolefin. Unlike other typical flame-retardant tubings, DWP-125 tubing is free of polybrominated biphenyls (PBBs) and polybrominated biphenyl oxides (PBBOs). In Europe, these chemicals are classified as environmentally hazardous substances. Typical applications include environmental sealing and protection of irregular shapes, such as wire splices and break-outs, in demanding As DWP-125 shrinks, the inner adhesive liner melts and flows to seal and encapsulate components or splices contained within. Because DWP-125 has a three-toone shrink ratio, only a few sizes are needed to cover a wide range of substrate diameters, enhancing inventory efficiency. DWP-125 is UL-recognized and CSA-certified at 125°C, 600 V. Temperature rating Full recovery temperature: Continuous operating temperature: 125°C –40°C to 110°C Specifications* ® ® Type DWP-125 Raychem DWP-125 SCD UL E35586 CSA LR31929 *When ordering, always specify latest issue. Dimensions (millimeters/inches) W W1 d Expanded as supplied Fully recovered after heating D Size 1/8 3/16 1/4 3/8 1/2 3/4 1 1 1/2 2 Inside diameter (including core) D (min.) Expanded as supplied 3.2 0.125 4.8 0.187 6.4 0.250 9.5 0.375 12.7 0.500 19.0 0.750 25.4 1.000 38.1 1.500 50.8 2.000 d (max.) Recovered after heating 1.0 0.040 1.5 0.060 2.0 0.080 3.0 0.120 4.0 0.157 6.0 0.230 8.0 0.320 13.0 0.530 20.0 0.800 Recovered wall thickness** W Nominal total wall 1.0 0.040 1.40 0.055 1.45 0.057 1.65 0.065 1.78 0.070 2.03 0.080 2.50 0.100 2.50 0.100 2.50 0.100 **Wall thickness will be less if tubing recovery is restricted during shrinkage. Ordering information Colors Size selection Standard packaging Ordering description Standard Black Nonstandard Red, yellow, blue, green, and white; other colors available on request. Always order the largest size that will shrink snugly over the component being covered. 4-foot lengths Specify product name, size, and color; for example, DWP-125 1/4-0 (0=Black). W1 Nominal adhesive wall 0.25 0.010 0.51 0.020 0.56 0.022 0.68 0.027 0.76 0.030 0.76 0.030 0.76 0.030 0.76 0.030 0.76 0.030 Specification values Physical Electrical Chemical Property Dimensions Longitudinal change Tensile strength Ultimate elongation Secant modulus (as supplied) Low-temperature flexibility (1 hour at –30°C/–22°F) Heat shock (4 hours at 250°C/482°F) Heat aging (7 days at 158°C/316°F) Followed by tests for: Tensile strength Ultimate elongation Flexibility Dielectric withstand at 2500 V Dielectric breakdown Dielectric strength Restricted shrinkage Dielectric withstand at 2500 V Dielectric strength Volume resistivity Corrosive effect (7 days at 158°C/316°F) Copper stability (7 days at 158°C/316°F) Followed by test for: Ultimate elongation Flammability Unit mm (inches) percent psi (MPa) percent psi (MPa) Requirement See reverse +0, –10 1500 (10.3) minimum 200 minimum 1.5 x 104 (103) maximum Method of test ASTM D 2671 ASTM D 2671 ASTM D 2671 ASTM D 2671 ASTM D 2671 No cracking UL 224 No cracking ASTM D 2671 ASTM D 2671 percent percent seconds volts volts/mil (kV/mm) seconds volts/mil (kV/mm) ohm-cm 70% minimum of original 100 minimum No cracking 60 minimum UL 224 UL 224 UL 224 ASTM D 2671 50% minimum of unaged specimens 500 (19.7) minimum Pass 60 minimum ASTM D 2671 ASTM D 2671 UL 224 ASTM D 2671 500 (19.7) minimum 1014 minimum No corrosion ASTM D 2671 ASTM D 2671 ASTM D 2671 Procedure B ASTM D 2671 Procedure B No brittleness, glazing, cracking, or severe discoloration of tubing. No pitting or blackening of copper. percent 100 minimum Pass ASTM D 2671 UL 224, all tubing Users should independently evaluate the suitability of the product for their application. Tyco Electronics Corporation 300 Constitution Drive Menlo Park, CA 94025-1164 USA Tel: (800) 926-2425 (US & Canada) Tel: +1 (650) 361-3860 (All other countries) Faraday Road Dorcan, Swindon, SN3 5HH United Kingdom Tel: +44 1793 528171 3816 Noborito, Tama-ku Kawasaki, Kanagawa 214-8533 Japan Tel: +81 44 900 5102 Asia Pacific Headquarters 26 Ang Mo Kio, Industrial Park 2 Singapore 569507 Tel: +65 4866 151 All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporation’s only obligations are those in the Standard Terms and Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the product. Tyco Electronics Corporation’s Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing without notification to the Buyer which do not affect compliance with any applicable specification. For more information about this product visit www.tycoelectronics.com © 1995, 2002 Tyco Electronics Corporation Printed in USA 1654053 6/02 Note: Except for dimensions, longitudinal change, and flammability, specification values apply to outer jacket only. Raychem is a trademark of Tyco Electronics Corporation.