EC9858-000

ZHD-SCE LOW FIRE HAZARD DIESEL RESISTANT H E AT S H R I N K I D E N T I F I C AT I O N S Y S T E M Technical Datasheet TTDS-263 Revision 7 April 2017 ZHD-SCE Zero Halogen, Diesel Resistant, Heat Shrink Identification Marker Sleeves for the identification of wires and cables. ZHD-SCE is presented as cut sleeves organised in ladder format. Manufactured using a specially developed radiation cross-linked, zero halogen material. ZHD-SCE is designed specifically to bridge the gap for installations where the highest performance is demanded from an identification sleeve, without compromising on safety or capability. ZHD-SCE Heat Shrink Identification Marker Sleeves are available as part of a complete identification system. The system comprises specific printers, thermal transfer ribbons and WINTOTAL software. PAGE 1 CLASS 1 DATA CLASSIFICATION - SEE POLICY TEC-02-04 TTDS-263 ZHD-SCE HEAT SHRINK IDENTIFICATION MARKER SLEEVES ZHD-SCE, LOW FIRE HAZARD, DIESEL RESISTANT Features Environmental Compliance • Zero Halogen • No Halogens, Sulphur, Nitrogen, Phosphorus and Cadmium sources above trace level. The flame retardant used in this product does not contain melamine cyanurate • Low Toxic Fumes • Non-flame propagating • Resistant to key rail and industrial fluids including diesel (defined by RW-2536) • Sleeve diameters from 2.4mm to 38.1mm • Shrink ratio 2:1 • Further information and a downloadable declaration covering RoHS and REACH compliance can be found at the ‘TE Product Compliance Support Centre’: • Pre-termination Cable Identification http://www.te.com/usa-en/utilities/productcompliance.html Temperature Rating Shelf Life • -55°C to 125°C (-67°F to 257°F) • Refer to TE document 408-121006 Cable Identification Shelf Life Applications Specifications / Approvals TE Connectivity Standard RW-2536 Rail Standards EN45545-2, Hazard Classifications 1 and 2, In accordance with requirement set R22/R23 BS 6853 Code of practice for fire precautions in the design and construction of passenger carrying trains. Interior minor use of materials of mass 100g to 500g vehicle category II EN 50343 Rolling stock applications - Rolling stock - Rules for installation of cabling - Appendix H NFPA 130 Standard for Fixed Guideway Transit and Passenger Rail Systems, Fire protection requirements, Interior Fire Propagation Resistance Federal Railroad Administration, DOT, Appendix B to Part 238, Test Methods and Performance Criteria for the Flammability and Smoke Emission Characteristics of Materials used in Passenger Cars and Locomotive Cabs SHAZAINENNSHI, Japan Railway Rolling Stock & Machinery Association 2003 Classification ‘Flame Retardant’ Serial number 2015-166K Where possible, TE has tested product as a finished item, including the print. Operational tests are followed by an assessment of mark adherence to validate fit form and function. Further details can be found in TE standard RW-2536. PAGE 2 CLASS 1 DATA CLASSIFICATION - SEE POLICY TEC-02-04 TTDS-263 ZHD-SCE HEAT SHRINK IDENTIFICATION MARKER SLEEVES ZHD-SCE LOW FIRE HAZARD, DIESEL RESISTANT Part Description ZHD-SCE -1K -4.8 -50 -S1 -9 9 Colour S1 Scoring (Optional) 50 Sleeve Length (mm) 4.8 Expanded Inside Diameter (mm) 1K Pack size ZHD-SCE Product family Options Pre-scoring Perforated score to produce multiple marker sleeves from each ZHD-SCE sleeve. Not scored Code Blank Side scored Code SS Sided scored with one pre-score Code SS1 1 Pre-score 2 Pre-scores Code Code S1 S2 Packaging sizes 5K Code PRINT WIDTH PRE-SCORE (S1) 1000 piece reels available for all sizes up to 25.4 2.5K Code SLEEVE 250 piece packs available for all sizes 1K Colours 49 (0.92 NOMINAL) PERFORATIONS Yellow 4 Red 2 2500 piece reels available for sizes 4.8 up to 25.4 5000 piece reels available for sizes 2.4 and 3.2 White 9 Green Blue Orange 5 6 3 CARRIER FIXING TAPE SIDE SCORE Specify product name, pack size (leave blank for 250), sleeve size (in mm), sleeve length (always 50), pre-score (leave blank if not required) and colour (SS) Dimensions in mm (inches) Ordering Information Ordering description Inside diameter As supplied After recovery (minimum) (Maximum) Recommended cable diameter use range mm inches mm inches mm inches ZHD-SCE - - 2.4 - 50 - - 2.4 0.094 1.19 0.047 1.27 to 1.90 0.050 to 0.075 ZHD-SCE - - 3.2 - 50 - - 3.2 0.126 1.58 0.060 1.77 to 2.66 0.069 to 0.105 ZHD-SCE - - 4.8 - 50 - - 4.8 0.189 2.36 0.090 2.54 to 4.06 0.100 to 0.160 ZHD-SCE - - 6.4 - 50 - - 6.4 0.250 3.18 0.125 3.81 to 5.46 0.150 to 0.215 ZHD-SCE - - 9.5 - 50 - - 9.5 0.375 4.75 0.187 5.59 to 8.12 0.220 to 0.320 ZHD-SCE - - 12.7 - 50 - - 12.7 0.500 6.35 0.250 6.99 to 10.79 0.275 to 0.425 ZHD-SCE - - 19.0 - 50 - - 19.0 0.730 9.53 0.375 10.16 to 16.25 0.400 to 0.640 ZHD-SCE - - 25.4 - 50 - - 25.4 1.000 12.70 0.500 14.29 to 21.59 0.563 to 0.850 ZHD-SCE - 38.1 - 50 - - 38.1 1.500 19.05 0.750 20.95 to 33.02 0.825 to 1.300 CLASS 1 DATA CLASSIFICATION - SEE POLICY TEC-02-04 TTDS-263 ZHD-SCE HEAT SHRINK IDENTIFICATION MARKER SLEEVES PAGE 3 ZHD-SCE LOW FIRE HAZARD, DIESEL RESISTANT Printer Information Print quality and print performance can only be guaranteed when specific TE printer and ribbons are used. The current list of printers and ribbons can be found in TE document 411-121005 ‘Identification Printer Product Ribbon Matrix’. This document can be found in ‘Access Our Tools’: http://www.te.com/usa-en/utilities/access-product-toolsand-resources.html Software WINTOTAL software, available to download for a 14 day evaluation period from the Identification Printer Software page: http://www.te.com/usa-en/products/identification-labeling/ printers-software.html Contact a TE representative for further information www.te.com/rail TE Connectivity, TE Connectivity (logo) and Every Connection Counts are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2017 TE Connectivity Ltd. family of companies All Rights Reserved. PAGE 4 CLASS 1 DATA CLASSIFICATION - SEE POLICY TEC-02-04 TTDS-263 ZHD-SCE HEAT SHRINK IDENTIFICATION MARKER SLEEVES