F80769-000

TINEL LOCK RING 3 CODE 41 - TINEL-LOCK BACKSHELL TXR41AB00-1608AI-S SERIES TXR: RING INCLUDED (SEE RING OPTION) TX: RING NOT INCLUDED CONNECTOR INTERFACE MATERIAL REFER TO CH00-0250-008 FINISH REFER TO CH00-0250-008 ANGLE DASH NUMBER (TABLE 1) ENTRY SIZE (TABLE 2) RING OPTION AI - TO SUIT SINGLE BRAID BI - TO SUIT DOUBLE BRAID FOR TX, LEAVE BLANK MODIFICATION CODE REFER TO CH00-0250-008 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A BRAIDED CABLE SHIELD AND A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-008. 3. SEE DRAWING TR FOR DETAIL ON TINEL-LOCK RING, RINGS ARE DESIGNED TO BE HEATED ELECTRICALLY, ALL RINGS ARE MARKED WITH THERMOCHROMIC PAINT WHICH CHANGES COLOUR WHEN INSTALLATION TEMPERATURE IS REACHED. 4. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER LESS RING DESIGNATOR. (e.g. 06090-TXR41AB00-1206). RING SHALL BEAR NO MARKING. 5. FOR LARGER ENTRY SIZES, A 2 PIECE BACKSHELL ASSEMBLY (TYPE 2) IS SUPPLIED. 6. BACKSHELL MATES TO MIL-DTL-38999, SERIES I AND II, CLASS E AND T, MS27466, MS27467, MS27468, MS27472, MS27473, MS27474, MS27479, MS27480, MS27481, MS27484, MS27497, MS27652, MS27653, MS27656 CONNECTORS. 7. THESE DIMENSIONS APPLY IF A SELF-LOCKING COUPLING NUT IS USED. DATE DRAWN K.WINCZURA 04/12/2014 CHECKED 04/12/2014 APPROVED K.SHEPPARD 04/12/2014 APPROVED H.SMITH 16/02/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECO-12-021161 J REVISED PER ECO-15-002319 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 04.12.12 16.02.15 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED G.WELLS H.SMITH TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-38999 SERIES I & II TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT TXR41 J 1 IF MAX ENTRY IS EXCEEDED BACKSHELL WILL BE SUPPLIED AS TYPE 2 16,80 `0,50 XXXX A THREAD ØK ØY ØZ XXXX ØS A THREAD PART MARK HERE ØB 26,80 SILICONE O-RING ØB 26,50 PART MARK HERE 5 STRAIGHT BACKSHELL - TYPE 2 STRAIGHT BACKSHELL - TYPE 1 C 16,80 `0,50 F D G 45° BACKSHELL - TYPE 2 45° BACKSHELL - TYPE 1 H W 16,80 ` 0,50 M E J T 90° BACKSHELL - TYPE 1 H W 90° BACKSHELL - TYPE 2 16,80 ` 0,50 T J E M 90° BACKSHELL - TYPE 1 STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE DATE DRAWN K.WINCZURA 04/12/2014 CHECKED 04/12/2014 APPROVED K.SHEPPARD 04/12/2014 APPROVED H.SMITH 16/02/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECO-12-021161 J REVISED PER ECO-15-002319 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 04.12.12 16.02.15 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED G.WELLS H.SMITH 90° BACKSHELL - TYPE 2 STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-38999 SERIES I & II TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT TXR41 J 2 MODIFICATION S (SELF-LOCKING COUPLING NUT) 21,60 `0,50 BACKSHELL - TYPE 1 TABLE 1 ORDER SHELL SIZE NO. SER I/ SER II 08 9/8 10 11 / 10 12 13 / 12 14 15 / 14 16 17 / 16 18 19 / 18 20 21 / 20 22 23 / 22 24 25 / 24 TABLE 2 ENTRY SIZE 04 05 06 07 08 10 12 14 16 18 20 22 24 BACKSHELL - TYPE 2 THESE DIMENSIONS APPLY IF BACKSHELL IS STAINLESS STEEL OR NICKEL ALUMINIUM BRONZE ØB MAX 18,3 21,5 24,5 27,8 30,8 34,1 37,3 40,5 43,7 A THREAD 7/16-28UNEF 9/16-24UNEF 11/16-24UNEF 13/16-20UNEF 15/16-20UNEF 1 1/16-18UNEF 1 3/16-18UNEF 1 5/16-18UNEF 1 7/16-18UNEF ØB MAX 7 18,0 21,0 25,0 28,0 31,0 34,0 37,0 40,0 43,5 MAX ENTRY 04 07 08 10 12 14 16 18 20 C ±0,5 16,4 17,2 17,6 18,5 19,2 19,6 20,4 20,8 21,7 D ±0,5 26,8 27,5 28,0 29,0 29,7 30,5 30,9 31,1 32,1 W ±0,5 21,0 24,0 27,0 31,0 34,0 35,0 38,0 42,0 45,0 T ±0,5 14,0 15,5 17,0 19,5 21,0 20,0 21,5 24,0 25,5 E ±0,5 26,20 27,95 29,45 31,00 32,70 34,25 35,80 37,40 38,90 W ±0,5 21,3 24,4 28,4 31,2 34,3 38,6 40,8 43,8 46,5 T ±0,5 16,4 17,3 19,5 21,0 22,8 25,3 26,1 27,6 29,1 E ±0,5 26,4 28,2 29,7 31,2 32,9 34,5 36,1 37,6 39,1 THESE DIMENSIONS APPLY IF BACKSHELL IS STAINLESS STEEL OR NICKEL ALUMINIUM BRONZE ØZ MIN 6,35 7,92 9,53 11,10 12,70 15,88 19,05 22,23 25,40 28,58 31,75 34,93 38,10 ØS 9,49 +/-0,04 11,06 +/-0,04 12,66 +/-0,04 14,21 +/-0,07 15,81 +/-0,07 18,96 +/-0,08 22,14 +/-0,08 25,30 +/-0,08 28,48 +/-0,08 31,65 +/-0,08 34,83 +/-0,08 37,98 +/-0,08 41,15 +/-0,08 04/12/2014 CHECKED 04/12/2014 APPROVED K.SHEPPARD 04/12/2014 H.SMITH ØY ± 0,3 14,00 15,50 17,10 18,70 20,30 23,50 26,70 29,80 33,00 36,20 39,40 42,50 45,70 DATE DRAWN K.WINCZURA APPROVED SELF-LOCKING MECHANISM A THREAD ØK 7 A THREAD ØB 7 ØB 7 SELF-LOCKING MECHANISM SELF-LOCKING MECHANISM 16/02/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECO-12-021161 J REVISED PER ECO-15-002319 ØK MAX NA 21,0 21,0 21,0 24,5 29,0 32,5 35,5 37,0 40,0 43,5 48,5 52,1 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 04.12.12 16.02.15 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED G.WELLS H.SMITH ØK MAX 7 NA 24,6 24,6 24,6 28,3 32,4 35,6 38,5 41,7 43,9 47,0 50,0 56,0 F ±0,5 NA 12,5 12,5 12,5 13,1 13,5 14,5 15,5 16,1 16,5 17,0 18,5 21,9 G ±0,5 NA 27,5 27,5 27,5 28,0 29,0 29,7 30,5 30,9 31,1 32,1 35,3 38,1 H ±0,5 NA 24,0 24,0 24,0 27,0 31,0 34,0 35,0 38,0 42,0 45,0 54,5 58,0 M ±0,5 NA 15,5 15,5 15,5 17,0 19,5 21,0 20,0 21,5 24,0 25,5 31,0 33,0 J ±0,5 NA 27,95 27,95 27,95 29,45 31,00 32,70 34,25 35,80 37,40 38,90 42,00 46,00 H ±0,5 NA 24,3 24,3 24,3 28,3 31,1 34,2 38,5 40,7 43,7 46,4 50,0 53,5 M ±0,5 NA 17,2 17,2 17,2 19,4 21,0 22,8 25,3 26,1 27,6 29,1 31,0 33,0 J ±0,5 NA 28,2 28,2 28,2 29,7 31,2 32,9 34,5 36,1 37,6 39,1 42,0 46,0 TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-38999 SERIES I & II TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT TXR41 J 3