FCA-410-1617L

CII Mid-Range Relays FCA-410 Series, 10 Amperes, 4PDT Product Facts n Hermetically Sealed n All Welded Construction n Balanced Force n Permanent Magnet Drive n 4PDT switching in one inch cube n Contacts — Silver Cadmium Oxide with Gold Plating n Coils for DC and AC 50 to 400Hz or 400Hz n Weight 2.72 ounces max. (77 grams max.) n Qualified to M83536/15, /16 design. We also manufacture 2-pole and 6-pole versions of this relay. The Series FCA-410 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar FCA-210 — 10 Amp DPDT Relay FCA-610 — 10 Amp 6PDT Relay Available FCA-415 — 15 Amp 4PDT, Has the same specifications as the FCA-410 except is rated at 15 amps. (Commercial Only) Contact Rating — Amperes Ratings Are Continuous Duty Type of Load Life (Min.) Cycles x 103 28 VDC 120VAC 400Hz Resistive Inductive Motor Lamp 100 20 100 100 10 8 4 2 10 8 4 2 120/200VAC 400Hz-3Ø 60Hz-3Ø* 10 2.5 8 2.5 4 2.0 2 1.0 *60 Hz loads rated for 10,000 operations Overload Current — 40 AMPS DC, 60 AMPS 400Hz Rupture Current — 50 AMPS DC, 80 AMPS 400Hz Contact Make Bounce —1 MILLISECOND AT NOMINAL VOLTAGE Max. Contact Drop at 10 Amps — INITIAL 0.100 VOLTS End of Life — 0.125 VOLTS General Specifications Temperature Rating — -70˚C TO + 125˚C Altitude — 300,000 Feet Shock* — Z & Y Enclosures — 200 g for 6 mS W, X & M Enclosures — 100 g for 6 mS Vibration, Sinusoidal* — Z & Y Enclosures — 0.12 DA 10 to 70Hz 30 g 70 to 3000Hz W, X & M Enclosures — 0.12 DA 10 to 57Hz 20 g 57 to 3000Hz Vibration, Random* — Z & Y Enclosures — 0.4 g2/Hz 50-2000Hz W, X & M Enclosures — 0.2 g2/Hz 50-2000Hz Dielectric Strength — At Sea Level — All circuits to ground and circuit to circuit — 1250 V rms Coil to ground — 1000 V rms At 80,000 Feet — 350 V rms Insulation Resistance — Initial (500 VDC) — 100 MΩ Min. After Life or Environmental Tests — 50 MΩ Min. Operate Time at Nominal Voltage — DC Relays — 15 ms or less AC Relays — 20 ms or less Release Time at Nominal Voltage — DC Relays — 15 ms or less AC Relays — 50 ms or less * Max. contact opening under vibration or shock 10 microseconds Coil Data Coil Code 1 2 3 4 (A) 5 6 7 8 9 A. B. C. D. E. Nominal Voltages Freq. Hz DC Res. AC Amps (B) 6 12 28 28 48 28 28 115 115 DC DC DC DC DC 400Hz 50/400Hz 400 Hz 50/400 Hz 18 Ω 70 Ω 290 Ω 290 Ω 865 Ω 225 mA 120 mA 40 mA 30 mA Over Temperature Range Pickup or Dropout or Must Hold Below Volts Above Volts Voltage (C) 4.5 0.3 2.5 9.0 0.75 4.5 18.0 1.5 7.0 18.0 1.5 7.0 32.0 2.5 14.0 22.0 1.25 10.0 22.0 1.25 10.0 90.0 5.0 40.0 95.0 5.0 40.0 CODE 4 COILS HAVE BACK EMF SUPPRESSION TO 42 VOLTS MAX. DC COIL RESISTANCE ± 10% AT 25˚C; AC COIL MAX. CURRENT AT NOMINAL VOLTAGE. RELAY WILL STAY IN PICKED-UP STATE DOWN TO MUST HOLD VOLTAGES SHOWN. MAX. OVER-VOLTAGE: 6 & 12 VDC COILS 120% OF NOMINAL; ALL OTHERS 110% OF NOMINAL. COILS AVAILABLE FOR OTHER VOLTAGES AND FOR AC 50/60HZ. NOTE: Only DC Coil Models are QPL Approved. 5–18 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Mid-Range Relays FCA-410 Series, 10 Amperes, 4PDT (Continued) Below are shown the standard terminal types and the enclosures available. Note that the pin configuration for coil connections is determined by the coil supply voltage. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ± .010 and (Millimeters ± .25) except as noted. Enclosures Terminals Terminals on 0.200 centers. Coil terminals: X1-X2. Socket Pins are Gold Plated. Circuit Board Pins are Tin/Lead Plated. CODE “A” Socket Pins-All DC Coils All Enclosures have cupro-Nickel cans bright acid tin/lead plated after assembly to terminal headers. Socket Pins-115 VAC Coils .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket .270 (6.86) CODE “Z” .100 (25.4) 1.051 (25.79) BLUE BEAD .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket .270 (6.86) CODE “D” -X2 1.051 (25.79) .062 ±.001 Pin (1.57 ± .02 ) 14 places +X1 -X2 CODE .150 typ. “Y” (3.8) .062 ±.001 Pin (1.57 ± .02 ) 14 places +X1 1.015 (25.79) BLUE BEAD .625 .937 15.88 23.80 CODE “B” Circuit Board Pins-All DC Coils .270 (6.86) .312 7.92 FULL R 6 PLCS SEE NEXT PAGE 5 CII Mid-Range Relays 1.015 (25.79) 1.396 (35.46) 1.446 (36.73) + .002 .062 - .001 Dia. Pin (1.57 +- .05 ) 14 Plcs. .02 FOR MORE COIL 1.00 (25.4) -X2 TERMINAL OPTIONS +X1 CODE "W" BLUE BEAD CODE “C” Solder Hooks-AC or DC Coils CODE “X” .150 Typ. (3.8) 1.00 (25.4) .300 ± .020 (7.26) ± .51 -X2 .040 (1.02) .156 (3.96) 1.718 Max. (43.64) 0.80 DIA (2.03) FULL R 6 PLCS .312 (7.92) 6-32 UNC-2A 3 Studs * .375 (9.52) 1.00 (25.4) .031 (.787) .625 .937 15.88 23.80 1.015 (25.78) 1.015 (25.79) 1.396 (35.46) 1.446 (36.73) .343 (8.71) .687 (17.44) .160 (4.06) + .002 .062 - .001 Dia. Pin (1.57 +- .05 )14 Plcs. .02 +X1 1.051 (25.79) 1.051 (25.79) 1.718 Max. (43.64) BLUE BEAD .687 (17.44) .160 (4.06) .040 (1.02) *Metric threads available,To specify use M in place of W 5–19 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com CII Mid-Range Relays FCA-410 Series, 10 Amperes, 4PDT (Continued) Terminals (Continued) CODE “E” Socket Pins- 28 VAC Coils .270 (6.86) CODE “F” Circuit Board Pins-115 VAC Coils CODE “G” Circuit Board Pins- 28 VAC Coils .270 (6.86) .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket .270 (6.86) BLUE BEAD BLUE BEAD + .002 .062 - .001Dia. Pin ) 14 Plcs. (1.57 +- .05 .02 +X1 BLUE BEAD + .002 -X2 .062 - .001Dia. Pin (1.57 +- .05 ) 14 Plcs. .02 -X2 -X2 + .002 .062 - .001Dia. Pin ) 14 Plcs. (1.57 -+ .05 .02 +X1 +X1 Terminal Wiring A & B Pin Terminal All DC Coils 1 D C X2 - 2 + C Hook Terminal All AC & DC Coils 3 1 X2 - D C 2 + Transient Suppression Cir. 3 1 X2 - D C 2 + 3 D & F Pin Terminal 115 VAC Coils D 3 B B A X1 + A X1 + A X1 + A X2 Diodes used in transient suppression and in AC rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. X2 C AC X1 B A X1 BLUE BEAD BLUE BEAD NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. 2 1 D AC B BLUE BEAD 2 1 C B BLUE BEAD E & G Pin Terminal 28 VAC Coils BLUE BEAD .600 (15.24) .400 (10.16) .200 (5.08) -X2 .600 (15.24) +X1 Terminal designations are for reference only and do not appear on the header. .400 (10.16) BLUE BEAD .200 (5.08) TERMINAL VIEW HOW TO ORDER FCA-415FCA-410 A Y 4 RELAY TYPE TERMINALS (Socket Pins) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). NOTE: Only DC coil models are QPL Approved * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 5–20 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com 3