FLTWC0111-20-9

SPECIFICATION CONTROL DRAWING TITLE FLTW+0111 Date GENERAL PURPOSE HOOKUP WIRE, MODIFIED POLYESTER-INSULATED, 150 VOLT 3-15-13 Revision E The complete requirements for procuring the wire described herein shall consist of this document and the issue in effect of Raychem Specification WCD 3106, UL Subject 758, Style 10327, File E303150 and carries UL labels to this effect. CONDUCTOR - TIN-COATED COPPER INSULATION - FLAME RETARDED, MODIFIED POLYESTER CONSTRUCTION DETAILS FINISHED WIRE PART NUMBER 1/ FLTWB0111-30-* WIRE SIZE (AWG) CONDUCTOR STRANDING (number x AWG) NOMINAL CONDUCTOR DIAMETER (in.) (mm) 30 7 x 38 .012 (.305) MAXIMUM RESISTANCE AT 20°C (ohms/1000 ft.) (ohms/km) 116. DIAMETER (in.) (mm) MINIMUM NOMINAL MAXIMUM NOMINAL WEIGHT (lbs/1000 ft.) (kg/km) (381.) .019 (.483) .020 (.508) .021 (.533) .47 (.70) FLTWB0111-28-* 28 7 x 36 .015 (.381) 72.8 (239.) .022 (.559) .023 (.584) .024 (.610) FLTWB0111-26-* 26 7 x 34 .019 (.483) 45.8 (150.) .028 (.711) .029 (.737) .030 (.762) .69 (1.03) 1.1 (1.64) FLTWB0111-24-* 24 7 x 32 .024 (.610) 28.7 (94.2) .032 (.813) .034 (.864) .035 (.889) 1.7 (2.53) FLTWC0111-26-* 26 19 x 38 .019 (.483) 45.8 (150.) .027 (.686) .028 (.711) .029 (.737) 1.1 (1.64) FLTWC0111-24-* 24 19 x 36 .024 (.610) 28.7 (94.2) .032 (.813) .033 (.838) .034 (.864) 1.7 (2.53) FLTWC0111-22-* 22 19 x 34 .030 (.762) 18.1 (59.4) .038 (.965) .039 (.991) .040 (1.02) 2.5 (3.72) FLTWC0111-20-* 20 19 x 32 .038 (.965) 11.4 (37.4) .046 (1.17) .047 (1.19) .048 (1.22) 3.9 (5.80) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Page 1 of 2 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Raychem Wire & Cable 501 Oakside Avenue Redwood City, CA 94063-3800 Phone: 1-800-227-8816 Fax: 1-650-361-6297 © 2005-2013 Tyco Electronics Corporation,. All rights reserved. Page SPECIFICATION CONTROL DRAWING 2 of 2 Revision E WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 125°C VOLTAGE RATING: 150 volts (rms) at sea level INSULATION ELONGATION AND TENSILE STRENGTH: Elongation, 280% (minimum) Tensile Strength, 4500 lbf/in2 (minimum) INSULATION FLAWS: Spark Test, 1.5 kV (rms) Impulse Dielectric Test, 4.0 kV (peak) INSULATION THICKNESS: .0025 inch (minimum), .003 inch (minimum average) SHRINKAGE: 125°C for 1 hour, 0.125 in. (maximum) per end THERMAL STABILITY: 158°C for 168 hours, Elongation Retention, 65% (minimum) Tensile Strength Retention, 90% (minimum) VOLTAGE WITHSTAND (Post Environmental): 1500 volts (rms), 60 Hz PART NUMBER: The “+” in the part number in the upper right hand corner of pages 1 and 2 shall be replaced with a letter designator to define conductor stranding (see part numbers in table). B = 7 Strands C = 19 Strands The “*” in the part numbers on page 1 shall be replaced by a color code designator. 1/ Example: AWG 26, 19 strands, white: FLTWC0111-26-9 AWG 26, 19 strands, white with black stripe: FLTWC0111-26-90 1/ See footer section on page 1 SCD FLTW+0111