H4P53K6DCA

Axial Leaded Precision Resistors Type HOLCO Series Key Features Ultra-Precision - Down To 0.05% Low TCR – Down To 5ppm/°C Long Term Stability Up To 1 Watt At 70°C The Holco range of Precision Metal Film Resistors meets the requirement for economically priced components for industrial and military applications. The manufacturing facility utilises closely controlled production processes including the sputter coating of metal alloy films to ceramic substrates, and laser spiralling to achieve close tolerance and high stability resistors. An epoxy coating is applied for environmental and mechanical protection. Commercially the Series is available in two case sizes, from 1 ohm to 4M ohms, tolerances from 0.05% to 1% and TCR's from 5ppm/°C to 100ppm/°C. Characteristics – Electrical H4P Power rating @70°C 1W Temperature Rise 70°C Limiting Element 500v Voltage H4 0.5W 55°C 350v H8 0.25W 40°C 350v General Data Lead Material Encapsulation Resistor Marking Solvent Resistance 1773230 Rev. H 03/2019 Dimensions in millimetres unless otherwise specified Solderability to BS CECC 40101 004 Para 4.15.1 Conformal Epoxy Coating Legend printed in accordance with CECC 40000 Para 2.4 The epoxy coating and print will withstand the action of all commonly used industrial cleansing solvents Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Axial Leaded Precision Resistors Resistance Range by TCR and Tolerance TCR Ppm/°C 5 10 15 25 50 100 0.05% 10R500K 10R – 1M0 10R – 1M0 10R – 1M0 10R – 1M0 10R – 1M0 H4P 0.1% 0.25% 10R500K 10R – 1M0 10R – 1M0 10R – 2M0 10R – 2M0 10R – 2M0 0.5% 1.0% 10R500K 10R – 1M0 10R – 1M0 10R – 2M0 10R – 4M0 10R – 4M0 0.05% 10R500K 10R – 1M0 10R – 1M0 10R – 1M0 10R – 1M0 10R – 1M0 H4 0.1% 0.25% 10R500K 10R – 1M0 10R – 1M0 10R – 2M0 10R – 2M0 10R – 2M0 0.5% 1.0% 10R500K 10R – 1M0 10R – 1M0 10R – 2M0 10R – 4M0 10R – 4M0 0.05% 10R500K 10R – 1M0 10R – 1M0 10R – 1M0 10R – 1M0 10R – 1M0 H8 0.1% 0.25% 10R500K 10R – 1M0 10R – 1M0 10R – 2M0 10R – 2M0 10R – 2M0 0.5% 1.0% 10R500K 10R – 1M0 10R – 1M0 10R – 2M0 10R – 4M0 10R – 4M0 Performance Characteristics Voltage Coefficient of Resistance (Between 10% and Full Rated Voltage) Insulation Resistance at 500 Volts Resistance to Soldering Heat (260°C for 10 Secs.) Short Term Overload (6.25 Times Rated Wattage for 5 Seconds) Ambient Temperature Range Rapid Change of Temperature (-55°C to +155°C, 5 cycles) Shelf Life (at Normal Room Temp.) Vibration (10-500 HZ Amplitude 0.75mm, or Acceleration 98m/s2 whichever is less severe, sweep duration 6 hours) Vibration (55-2000 Hz Simple Harmonic Motion, Max. Acceleration 98m/s2, Duration 35±5 Minutes) Bump (390m/s2, 4000 Bumps) Load Stability Damp Heat Steady State 1773230 Rev. H 03/2019 Dimensions in millimetres unless otherwise specified Typical Data Less Than 5ppm/Volt Applied Reference N/A Greater Than 10¹² Ohms N/A Less Than 0.05% Less Than 0.06% BS CECC 40101 004 Para 4.15.2 BS CECC 40101 004 Para 4.11 -55°C to +155°C Less Than 0.04% BS CECC 40101 004 BS CECC 40101 004 Para 4.16 Less Than 0.05% Per Annum N/A Less Than 0.04% BS CECC 40101 004 Para 4.19 Less Than 0.04% MIL STD 202 METHOD 204-C Less Than 0.03% BS 2011 Part 2.1 Eb 1977 (1984) N/A BS CECC 40101 004 Para 4.21 See graph See Graph Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Axial Leaded Precision Resistors Dimensions H4P H4 H8 Body Length (L) maximum: 10.50mm 10.50mm 7.20mm Body Diameter (D) maximum: 3.70mm 3.70mm 2.70mm Lead Diameter (d) maximum: 0.60mm 0.60mm 0.60mm Lead Length (l) nominal: 30.0mm 30.0mm 30.0mm Recommended Mounting Pitch: 12.70mm 12.70mm 10.2mm Weight (g/100 resistors) 40 40 24 N.B. To prevent damage to the components conformal coating, the leads should be adequately supported during the forming process Long Term Stability 1773230 Rev. H 03/2019 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Axial Leaded Precision Resistors Derating How To Order H8 Common Part H4P H4 H8 1773230 Rev. H 03/2019 100R Resistance Value 1.0Ω- 1R0 10Ω - 10R 1KΩ (1000 Ohms)- 1K0 10KΩ (10,000 ohms) – 10K Dimensions in millimetres unless otherwise specified B Tolerance Y TCR Code A Release A – 0.05% B – 0.1% C – 0.25% D – 0.5% F – 1.0% A – 5ppm B – 10ppm Y – 15ppm D – 25ppm C – 50ppm Z – 100ppm A – Part can only be sold with commercial or C of C release Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help