HDP26-24-31PE-L017

File E28476 Service Request: 1181364 Issued: July 13, 2009 Revised: January 31, 2023 REPORT on COMPONENT – Connectors for Use in Data, Signal, Control and Power Applications - Component TYCO ELECTRONICS CORP MIDDLETOWN,PA Copyright  2009 Underwriters Laboratories Inc. UL LLC authorizes the above named company to reproduce this Report provided it is in its entirety. UL LLC authorizes the above named company to reproduce the latest pages of that portion of this Report consisting of this Cover Page through Page 3. File E28476 Vol. 124 Sec. 2 and Report Page 1 Issued: Revised: 2009-07-13 2023-01-31 DESCRIPTION PRODUCT COVERED: USR – Component Connectors, Series YHDP24 or YHDP26 or HDP24- or HDP26, followed by 18-6-, 18-8-, 18-14-, 18-20-, 18-21-, 24-9-, 24-14-, 24-16-, 24-18-, 24-19-, 24-21-, 24-23-, 24-29-, 24-31-, 24-33-, 24-34-, 24-35-, or 24-47- or 24-91-, followed by P or S, followed by N, T, or E, followed by four alphanumeric characters. USR – Component Connectors Cat. Nos. 2293821-1, 2293822-1, 2294433-1, 2294434-1, 2294435-1, 2294479-1, 2294482-1, 2294488-1. . GENERAL: These devices are multi-pole connectors intended for factory assembly on stranded copper conductors where the acceptability of combinations is determined by UL LLC. The devices are identified as follows: USR indicates investigation to United States Standards as referenced in the Test Record. Disconnecting Use - see Sec Gen for required marking * File E28476 Vol. 124 Sec. 2 and Report Page 1A Issued: New: 2009-07-13 2023-01-31 CAT NO NOMENCLATURE: Y A HDP I 2 II 6 III -24-21 IV S V N VI L024 VII A. Optional – Y - Indicates an identical construction Cat No. I. May be HDP Only - Designates Deutsch Heavy Duty Plastic Connector II. May be 2 only - Indicates Type, Bulk Packaged without Contacts or Accessories III. IV. Indicates Connector Style 4 = Receptacle (female) - Jam nut type mounting 6 = Plug (male) Indicates Shell Size and Insert Arrangements May be: 18-6, 18-8, 18-14, 18-20, 18-21, 24-9, 24-14, 24-16, 24-18, 24-19, 24-21, 24-23, 24-29, 24-31, 24-33, 24-34, 24-35, or 24–47 or 2491. Refer to Ills. 1 and 32 for specific arrangement layout V. Indicates Contact style P = Pin (male) S = Socket (female) VI. Indicates Wire sealing options, colors indicate slight dimensional diameter variation, to accommodate different wire insulation ranges and outer diameters. May be either N, T, or E. N = Normal position & wire seals (green ring) T = Thin wall wire seals (gray ring) E = Extra thin wall wire seals (blue ring) VII. Special Modifications Four Alphanumeric characters – Assigned for Commercial Purposes only File E28476 Vol. 124 Sec. 2 and Report Page 1B Issued: New: 2009-07-13 2023-01-31 The following table lists Cat. Nos that are identical except for Cat. No. designation. Cat. No. Identical YHDP24-18-14PEL024 HDP24-18-14PE-L024 YHDP24-18-20PEL024 HDP24-18-20PE-L024 YHDP24-18-20PNL024 HDP24-18-20PN-L024 2293821-1 HDP24-18-8PE-L024 2293822-1 HDP24-24-16PE-L024 YHDP24-24-18PEL024 HDP24-24-18PE-L024 YHDP24-24-18PNL024 HDP24-24-18PN-L024 YHDP24-24-19PEL024 HDP24-24-19PE-L024 YHDP24-24-21PEL024 HDP24-24-21PE-L024 YHDP24-24-21PNL024 HDP24-24-21PN-L024 YHDP24-24-23PEL024 HDP24-24-23PE-L024 YHDP24-24-29PEL024 HDP24-24-29PE-L024 YHDP24-24-31PEL024 HDP24-24-31PE-L024 2294433-1 HDP24-24-31PT-L024 2294434-1 HDP24-24-33PN-L024 YHDP24-24-35PEL024 HDP24-24-35PE-L024 YHDP24-24-47PEL024 HDP24-24-47PE-L024 YHDP24-24-9PE-L024 HDP24-24-9PE-L024 2294435-1 HDP26-24-18PN-L024 YHDP26-24-19PEL024 HDP26-24-19PE-L024 2294479-1 HDP26-24-21PN-L024 YHDP26-24-23PEL024 HDP26-24-23PE-L024 YHDP26-24-31PEL024 HDP26-24-31PE-L024 2294482-1 HDP26-24-31PT-L024 YHDP26-24-35PEL017 HDP26-24-35PE-L017 2294488-1 HDP26-24-9PN-L024 File E28476 Vol. 124 Sec. 2 and Report Page 1C Issued: New: 2009-07-13 2023-01-31 ENGINEERING CONSIDERATIONS (NOT FOR UL REPRESENTATIVE USE): Use - For use only in or with complete equipment where the acceptability of the combination is determined by UL LLC. Conditions of Acceptability - The following are among the considerations to be made when evaluating the device in the end-use product. Interruption of Current 1. These devices are not suitable for interrupting the flow of current by connecting or disconnecting the mating connector. Current-Carrying Capability and Current Ratings 2. These devices have not been subjected to the Temperature test and as a result do not have an assigned current rating. The device’s current carrying capability is to be reviewed in the end-use by measuring temperatures on the connector housing and/or terminals when current is flowing through the connector under conditions of normal use. File E28476 Vol. 124 Sec. 2 and Report Page 2A Issued: Revised: 2009-07-13 2017-03-07 8. The following crimp contacts have been evaluated for the wire sizes as tabulated below: Stamped and Formed Type - Pin / Socket 1060-12-0222 / 1062-12-0222 1060-12-0166 / 1062-12-0166 1060-16-0122 / 1062-16-0122 1060-16-0622 / 1062-16-0622 1060-16-0622 / 1062-16-0622 1060-16-0144 / 1062-16-0144 1060-16-0988 / 1062-16-0988 1060-16-1222 / 1062-16-1222 1060-14-0122 / 1062-14-0122 1060-20-0222 / 1062-20-0222 1060-20-0222 / 1062-20-0222 1060-20-0122 / 1062-20-0122 1060-20-0122 / 1062-20-0122 Solid Type *Socket 0462-203-04141 / 0462-203-08141 / 0462-203-12141 / 0462-209-16141 / 0462-201-16141 / 0462-201-16141 / / Pin 0460-204-0490 0460-204-08141 0460-204-12141 0460-215-16141 0460-202-16141 0460-202-16141 Wire Size, AWG 10 12, 14 14 – 18 16, 18 20 14 - 18 14 - 18 12 - 16 14 – 18 16, 18 20 16, 18 20 Wire Size, AWG 6 8 12, 14 14 16, 18 20 Force, lbf 20 20 20 20 8 20 20 20 20 20 8 20 8 Force, lbf 20 20 20 20 20 8