LEV200H5ANA

KILOVAC High Voltage DC Contactors KILOVAC LEV200 Series Contactor With 1 Form X Contacts Rated 500+ Amps, 12-900Vdc Product Facts Performance Data n Designed to be the lowest cost sealed contactor in the industry with its current rating (500+A carry, 2000A interrupt at 320Vdc) n Available with bottom or side mounting — not position sensitive n Optional auxiliary contact for easy monitoring of power contact position n Hermetically sealed — intrinsically safe, operates in explosive/harsh environments with no oxidation or contamination of coils or contacts, including long periods of non-operation n Typical applications include battery switching and backup, DC voltage power control, circuit protection and safety n Versatile coil/power connections n Designed and built in accordance to AIAG QS9000 n RoHS compliant Coil Data (Valid Over Temperature Range) 4 12Vdc 24Vdc Nominal Voltage Pickup Voltage (Will Operate) 9.0Vdc 19.0Vdc Voltage (Max.) 15Vdc 30Vdc 0.75 1.0 Dropout Voltage 5.0Vdc 2.0Vdc Coil Resistance @ 25° (Typ.) 11 ohms 40 ohms 48Vdc 38.0Vdc 60Vdc 2.0 7.0Vdc 145 ohms 72Vdc 57.0Vdc 90Vdc 3.0 12.0Vdc 357 ohms Ordering Information LEV200 A 4 N A A Typical Part Number 䊳 Series: LEV200 = 500+ Amp, 12-900Vdc Contactor Contact Form: A = Normally Open H = Normally Open with Aux. Contacts. (Option “H” requires option “A” in Coil Wire Length and option “N” in Coil Terminal Connector.) Note: Other auxiliary contact forms available. Consult factory. Coil Voltage: 4 = 12Vdc 5 = 24Vdc B = 28Vdc 6 = 48Vdc K = 72Vdc 8 = 96Vdc L = 110Vdc O = 115Vac 9 = 240Vac Notes: Consult factory for detailed specifications and availability of coils not listed in “Coil Data” table above. In coil voltage codes, 115Vac is designated by the letter “O” rather than the numeral “0.” Coil Wire Length: A = 15.3 in (390 mm) N = None (Requires option “A” in next step.) Coil Terminal Connector: N = None, stripped wires (Requires option “A” in previous step.) A = Studs, #10-32 Threaded (Electrical connection is made to the tab at the base of the stud.) Note: Specify option A, stripped wires, for coil voltages > 96Vdc For factory-direct application assistance, dial 800-253-4560, ext. 2055, or 805-220-2055. Mounting & Power Terminals: A = Bottom Mount & Male 10mm x M8 Threaded Terminals F = Side Mount & Male 10mm x M8 Threaded Terminals Consult factory regarding other available mountings and power terminals. Contact Arrangement, Power Contacts — 1 Form X (SPST-NO-DM) Rated Operating Voltage — 12 - 900 VDC Continuous (Carry) Current, Typical — 500 A @ 65°C, 400 mcm conductors Consult TE for required conductors for higher (500+ A) currents Make/Break Current at Various Voltages 1 — See graph next page Break Current at 320VDC 1 — 2,000 A, 1 cycle 3 Contact Resistance, Typ. (@200A) — 0.2 mohms Load Life — See graph next page Mechanical Life — 1 million cycles Contact Arrangement, Auxiliary Contacts — 1 Form A (SPST-NO) Aux. Contact Current, Max. — 2A @ 30VDC / 3A @ 125VAC Aux. Contact Current, Min. — 100mA @ 8V Aux. Contact Resistance, Max. — 0.417 ohms @ 30VDC / .150 ohms @ 125VAC Operate Time @ 25°C — Close (includes bounce), Typ. — 25 ms Bounce (after close only), Max. — 7 ms Release (includes arcing), Max @ 2000A — 12 ms Dielectric Withstanding Voltage — 2,200 Vrms @ sea level (leakage