M7139-350BG-200000

M7100 Pressure Transducer SPECIFICATIONS        FEATURES      Hermetic Pressure Ports Integral Electrical Connector Survives High Vibration ±0.25% Accuracy Water Resistant 1M Immersion APPLICATIONS      On and Off Highway Engines and Vehicles HVAC Refrigeration Controls Compressors Hydraulics Energy and Water Management SENSOR SOLUTIONS ///M7100 Performance standard on and off highway engine and vehicle OEMs Rugged for heavy equipment and outdoor use Designed specifically for high volume applications Stainless steel wetted surfaces Medium to high pressures UL Certified Gage The M7100 pressure transducer from the Microfused line of MEAS sets a new price performance standard for demanding engine and vehicle, and industrial applications. This transducer is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam and corrosive fluids. The transducer pressure cavity is machined from a solid piece of 17-4 PH stainless steel. The standard version includes a 1/4 NPT pipe thread allowing a leak-proof, all metal sealed system. This automotive grade pressure transducer with stainless steel hermetic pressure ports and integral electrical connector can boast up to 10,000psi (700bar). The M7100 is UL certified and exceeds the latest industrial requirements including surge protection and is overvoltage protected in both positive and reverse polarity. 04/2020 Page 1 M7100 Pressure Transducer STANDARD RANGES Range (psi) Range (bar) 0 to 150 0 to 010 0 to 200 0 to 014 0 to 300 0 to 020 0 to 500 0 to 035 0 to 01K 0 to 070 0 to 1K5 0 to 100 0 to 03K 0 to 200 0 to 05K 0 to 350 0 to 7K5 0 to 500 0 to 10K 0 to 700 Gage           PERFORMANCE SPECIFICATIONS Ambient Temperature: 25°C (unless otherwise specified); PARAMETERS MIN Steel Load Resistance TYP Copper MAX Steel Copper KΩ 10 Accuracy (combined linearity, hysteresis & repeatability) -0.25 0.25 %Span 1 2 Total Error Band -1.0 -2.5 1.0 2.5 %Span Compensated Temperature -20 -30 +85 120 °C Operating Temperature -40 +125 Storage Temperature -50 +125 Insulation Resistance (500VDC) 100 Short Circuit Protected °C 3 °C MΩ 4 Yes Output Noise @ 1kHZ Long Term Stability NOTES UNITS 10 -0.25 Frequency Response @ -3dB mV 0.25 1 %Span/Year kHz Notes 1. Best fit straight line. 2. TEB includes all accuracy errors, thermal errors, span and zero tolerances over the compensated temperature range. 3. Temperature range for product with standard cable is -20°C to +105°C. 4. Between sensor body to any pins of connector. 5. The maximum pressure that can be applied without changing the transducer’s performance or accuracy. 6. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer 7. Refer to pressure port Listing notes for installation recommendations. 8. This product can be configured for custom OEM requirements. Contact Factory for different transfer function. See “Pressure Transfer Function’ diagram. 9. Maximum temperature range for product with standard cable is -20oC to 105oC. 10. Do not apply torque to connector housing of transducer 11. To ensure proper environmental sealing and electrical connections when using a mating connector, follow the connector manufacturer’s installation guidelines. SENSOR SOLUTIONS ///M7100 04/2020 Page 2 M7100 Pressure Transducer ENVIRONMENTAL SPECIFICATIONS Ambient Temperature: 25°C (unless otherwise specified) PARAMETERS MIN Steel Copper TYP Steel Humidity (@40°C) 93 Pressure Overload 5X Pressure Cycle Mechanical Vibration Copper Steel Copper Mechanical Shock 3X 10M Steel Steel Copper UNITS NOTES %RH 2X Pressure Burst Media, Pressure Port MAX Copper Rated 5 Rated 6 Cycles Fluids compatible with 17-4PH Stainless Steel Fluids compatible with Brass 20g, 10 ~ 2000Hz MIL-STD-810C, Method 514.2, Curve L 10g peak, 55~2000Hz MIL-STD-202G, Method 204D, Test Condition C Half-Sine, Peak: 50g, 11ms MIL-STD-202, Method 213B, Condition A Half-Sine, Peak: 50g, 11ms MIL-STD-202G, Method 213B, Condition A Package Protection IP67 (IEC60529) . AGENCY APPROVALS RoHS: RoHS 2 (Directive 2011/65/EU) Industrial Control Equipment CSA 22.2 No. 14-10 UL508 Certified EMC Performance Criteria: Output Change < ±1.5% FSO ESD 8kV Contact/15kV Air; Discharge Rate >10s IEC 61000-4-2 EM Field 100V/m, 1kHz 80% Modulation, 80 ~ 1000MHz IEC 61000-4-3 Electrical Fast Transient Level 2, 1kV each line, capacitance coupling IEC 61000-4-4 Surge Level 2, 42Ω Impedance, Figure 11 (L-L 500V, L-E 1kV) IEC 61000-4-5 Conducted RF Level 2, 3V/130dB, 150kHz ~ 80MHz, 2s Dwell, Clamp Injection IEC 61000-4-6 Pulse Magnetic Field Level 3, 100A/m, 10 second pulse interval IEC 61000-4-9 Emission Class B, 30dB @ 30-230MHz, 37dB @ 230 – 1000MHz IEC 55022 SENSOR SOLUTIONS ///M7100 04/2020 Page 3 M7100 Pressure Transducer PRESSURE PORT INFORMATION Pressure Port Options Dim A Tightening Torque (Nm) 2 = G1/4, BS5380, Male .43 [11.0] 30~35 4 = 7-16-20 UNF, SAE J1926-2, Male, w/ O-Ring .36 [9.1] 18~20 5 = 1/4-18 NPT Male .56 [14.2] 2~3 T.F.F.T. 6 = 1/8-27 NPT Male .38 [9.7] 2~3 T.F.F.T. E = R1/4-19, Male .56 [14.2] 2~3 T.F.F.T. F = G1/4-19, BS5380, Female .64 [16.3] 30~35 P = 7/16-20UNF Female w/ Integral Valve Depressor; 1/4 Flare Gasket SAE J513C, Copper .64 [16.3] 15~16 Q = M10 x 1.0, ISO 6149-2, Male .37 [9.5] 15~16 S = M12 x 1.5, ISO 6149-2, Male .43 [11.0] 28~30 G = M14 x 1.5, ISO 6149-2, Male .43 [11.0] 30~35 U = G1/4, DIN 3852-E, Male .47 [12.0] 30~35 Notes: Installation *T.F.F.T.: Turns From Finger Tight Transducers can be installed by either spanner or deep socket. Torque values provided are for reference: actual torque depends upon mating port material, surface finish, lubrication and sealing mechanism. Transducers calibration and/or zero may shift if part is over-torqued during installation. Check for a zero shift after installing. CONNECTOR INFORMATION Connector Connector, Pin Plating Packard Metri-Pack 150 Series powerandsignal.com Sumitomo HV040 Series sumitomokenki.com AMP Econoseal-J Mark II 070 Series te.com SENSOR SOLUTIONS ///M7100 0.003 – 0.005 mm Sn 0.003 mm Sn over 0.0005 – 0.001 mm Cu 0.0004 mm Au over 0.0013 mm Ni 04/2020 Connector, Mating Housing P/N: 12065287 Terminals P/N: 12103881 Housing P/N: 6189-6907 Terminals P/N: 8100-3067/8 Housing P/N: 174357 Terminals P/N: 171630 Page 4 M7100 Pressure Transducer DIMENSIONS Dimensions are in INCHES [mm] SENSOR SOLUTIONS ///M7100 04/2020 Page 5 M7100 Pressure Transducer Copper Tube SENSOR SOLUTIONS ///M7100 04/2020 Page 6 M7100 Pressure Transducer CHARTS Pressure Transfer Function Output Type vs. Supply Output Type (Code) 3 4 Supply Voltage 4.75 ~ 5.25V* 8 ~ 32V Supply Current 4.0 ~ 10.0mA Output Voltage 0.5 ~ 4.5V* 1.0 ~ 5.0V Reverse Voltage 16V Overvoltage 16V 32V Protection * Output ratiometric to supply voltage Pressure Range psi bar 150P 200P 300P 500P 01KP 010B 014B 020B 035B 070B 1K5P 03KP 05KP 7K5P 10KP 100B 200B 350B 500B 700B SENSOR SOLUTIONS ///M7100 Connection Type Pressure Range (Cu Tube) psi bar 150P 010B 300P 020B 450P 1 Cable 2 feet 2 Cable 4 feet 030B 3 Cable 10 feet 500P 035B 7 AMP070 Connector 750P 050B 8 HV040 Sumitomo 9 Packard Connector M Cable 1 m N Cable 2 m P Cable 5 m R Cable 10 m 04/2020 Page 7 M7100 Pressure Transducer ORDERING INFORMATION M71 3 M – 300P G – T B 0000 Code 3 4 1 2 3 7 8 9 M N P R 0 B Output Output Voltage 0.5 – 4.5 V 1.0 – 5.0 V Copper Tube Pressure Port (T) is available only with Copper Port Material, C12200 Option (B) and all blue or green options Cable/Connectors Cable, 2 feet Cable, 4 feet Cable, 10 teet Amp Connector HV040 Sumitomo Packard Connector Cable 1 meter Cable, 2 meter Cable, 5 meter Cable, 10 meter Pressure Range [psi] psi bar 150P 010B 200P 014B 300P 020B 450P 030B 500P 035B 750P 050B 01KP 070B 1K5P 100B 03KP 200B 05KP 350B 7K5P 500B 10KP 700B Port Material 17-4PH Stainless Steel Copper, C12200* Code 2 4 5 6 E F P Options in green are for both Port Materials Options in blue are for Copper port only. Options in black are for 17-4PH St. Steel only Q S G U T Pressure Port Port G1/4,BS5380, Male 7/16-20 UNF, SAE J1926-2, Male, w/ O-ring 1/4-18 NPT Male 1/8-27 NPT Male R1/4-19 Male G1/4-19, BS5380, Female 7/16-20 UNF Female w/ Integral Valve Depressor; 1/4 Flare Gasket SAE J513C, Copper M10x1.0 ISO 6149-2, Male M12x1.5, ISO 6149-2, Male M14x1.5, ISO 6149-2, Male G1/4, DIN 3852-E, Male 1/4” OD Copper Tube* NORTH AMERICA EUROPE ASIA Measurement Specialties, Inc., a TE Connectivity Company Phone: 1 800-522-6752 Email: customercare.frmt@te.com Measurement Specialties (Europe), Ltd., a TE Connectivity Company Phone: +31 73 624 6999 Email: customercare.lcsb@te.com Measurement Specialties (China), Ltd., a TE Connectivity Company Phone: +86 0400-820-6015 Email: customercare.shzn@te.com TE.com/sensorsolutions Measurement Specialties, Inc., a TE Connectivity company. Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2015 TE Connectivity Ltd. family of companies SENSOR SOLUTIONS ///M7100 All Rights Reserved. 04/2020 Page 8