M83536/16-022L

SERIES FCA-410 Tyco Electronics Mid-Range Military/Aerospace Relays 10 AMPERES, 4PDT VED6 O R P L AP -R-8353 QPalified to MIL ● HERMETICALLY SEALED ● ALL WELDED CONSTRUCTION ● BALANCED FORCE ● PERMANENT MAGNET DRIVE ● 4PDT SWITCHING IN ONE INCH CUBE ● CONTACTS: SILVER CADMIUM m Qu nt s. co OXIDE WITH GOLD PLATING ● COILS FOR DC AND AC 50-400 Hz OR 400 Hz ● WEIGHT 2.72 OUNCES MAX. ( 77 GRAMS MAX.) co FCA-210: 10 AMP DPDT RELAY FCA-610: 10 AMP 6PDT RELAY m po ne The Series FCA-410 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture 2-pole and 4-pole versions of this relay. lin e AVAILABLE FCA-415: 15 AMP 4PDT, HAS THE SAME SPECIFICATIONS AS THE FCA-410 EXCEPT IS RATED AT 15 AMPS. on CONTACT RATING-AMPERES Ratings Are Continuous Duty TYPE OF LOAD Resistive Inductive Motor Lamp LIFE (MIN.) CYCLES X 103 28 VDC 120VAC 400HZ 10 8 4 2 10 8 4 2 100 20 100 100 120/200VAC 120/200VAC 400Hz-30 60Hz-30 * 10 8 4 2 * 60 Hz LOADS RATED FOR 10,000 OPERATIONS OVERLOAD CURRENT 40 AMPS DC, 60 AMPS 400HZ RUPTURE CURRENT 50 AMPS DC, 80 AMPS 400HZ CONTACT MAKE BOUNCE 1 MILLISECOND AT NOMINAL VOLTAGE MAX. CONTACT DROP AT 10 AMPS: INITIAL 0.100 VOLTS. END OF LIFE 0.125 VOLTS 24 2.5 2.5 2.0 1.0 SERIES FCA-410 Tyco Electronics Mid-Range Military/Aerospace Relays 10 AMPERES, 4PDT COIL DATA 6 12 28 28 48 28 28 115 115 DC DC DC DC DC 400HZ 50/400Hz 400 Hz 50/400Hz 18 Ω 70 Ω 290 Ω 290 Ω 865 Ω 225 mA 120 mA 40 mA 40 mA 4.5 9.0 18.0 18.0 32.0 22.0 22.0 90.0 95.0 m FREQ. HZ co 1 2 3 4 (A) 5 6 7 8 9 NOMINAL VOLTAGES s. COIL CODE OVER TEMPERATURE RANGE MUST HOLD DC RES. DROPOUT OR PICKUP OR VOLTAGE (C) AC AMPS (B) BELOW VOLTS ABOVE VOLTS 0.3 0.75 1.5 1.5 2.5 1.25 1.25 5.0 5.0 2.5 4.5 7.0 7.0 14.0 10.0 10.0 40.0 40.0 po ne nt A. CODE 4 COILS HAVE BACK EMF SUPPRESSION D. MAX. OVERVOLTAGE: 6 & 12 VDC COILS 120% OF TO 42 VOLTS MAX. NOMINAL; ALL OTHERS 110% OF NOMINAL. B. DC COIL RESISTANCE ± 10% AT 25˚C; E. COILS AVAILABLE FOR OTHER VOLTAGES AND AC COIL MAX. CURRENT AT NOMINAL VOLTAGE. FOR AC 50/60HZ. C. RELAY WILL STAY IN PICKED-UP STATE DOWN TO COIL VOLTAGES SHOWN. NOTE: Only DC Coil Models are QPL Approved. co lin e TEMPERATURE RATING: ALTITUDE: SHOCK: m GENERAL SPECIFICATIONS on VIBRATION, SINUSOIDAL:* VIBRATION, RANDOM * DIELECTRIC STRENGTH AT SEA LEVEL: Z,& Y ENCLOSURES W, X & M ENCLOSURES Z & Y ENCLOSURES W, X & M ENCLOSURES Z, & Y ENCLOSURES W, X & M ENCLOSURES ALL CIRCUITS TO GROUND AND CIRCUIT TO CIRCUIT. COIL TO GROUND DIELECTRIC STRENGTH AT 80,000 FEET: INSULATION RESISTANCE: -70˚C TO + 125˚C 300,000 FEET 200 G FOR 6 mS 100G FOR 6 mS 0.12 DA 10 TO 70Hz 30G 70 TO 3000 Hz 0.12 DA 10 TO 57 Hz 20G 57 TO 3000 Hz 0.4G2/Hz 50-2000Hz 0.2G2/Hz 50-2000Hz 1250 V rms 1000 V rms 350 V rms 100 MΩ MINIMUM INITIAL (500 VDC) AFTER LIFE OR ENVIRONMENTAL TESTS 50 MΩ MINIMUM OPERATE TIME AT NOMINAL VOLTAGE: DC RELAYS 15 mS OR LESS 20 mS OR LESS AC RELAYS RELEASE TIME AT NOMINAL VOLTAGE: DC RELAYS 15 mS OR LESS 50 mS OR LESS AC RELAYS * Max. contact opening under vibration or shock 10 microseconds 25 SERIES FCA-410 Tyco Electronics Mid-Range Military/Aerospace Relays 10 AMPERES, 4PDT Below are shown the standard terminal types and the enclosures available. Note that the pin configuration for coil connections is determined by the coil supply voltage. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ± .010 and (Millimeters ± .25) except as noted. ENCLOSURES TERMINALS s. -X2 .062 ±.001 Pin (1.57 ± .02 ) 14 places +X1 -X2 ne .062 ±.001 Pin (1.57 ± .02 ) 14 places po +X1 BLUE BEAD 1.051 (25.79) CODE "Y" .150 typ. (3.8) .625 .937 15.88 23.80 co lin e + .002 .062 - .001Dia. Pin (1.57 +- .05 ) 14 Plcs. .02 1.00 (25.4) TERMINAL OPTIONS on -X2 +X1 FOR MORE COIL CODE "X" .150 typ. (3.8) 1.00 (25.4) .300 ± .020 (7.26) ± .51 -X2 +X1 BLUE BEAD 0.80 DIA (2.03) FULL R 6 PLCS + .002 .062 - .001Dia. Pin (1.57 +- .05 ) 14 Plcs. .02 .040 (1.02) .156 (3.96) 1.718 Max. (43.64) CODE "W" .312 BLUE BEAD CODE "C" Solder Hooks-AC or DC Coils .312 7.92 1.015 (25.79) 1.396 (35.46) 1.446 (36.73) FULL R 6 PLCS SEE NEXT PAGE .270 (6.86) 1.051 (25.79) 1.015 (25.79) m CODE "B" Circuit Board Pins-All DC Coils MAX. co BLUE BEAD .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket .270 (6.86) .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket nt CODE "A" Socket Pins-All DC Coils .270 (6.86) All Enclosures have cupro-Nickel cans bright acid tin/lead plated after assembly to terminal headers. CODE "Z" "A" m Terminals on 0.200 centers. CODE "D" Coil terminals: X1-X2; See Page 26. Socket Pins-115 VAC Coils Socket Pins are Gold Plated. Circuit Board Pins are Tin/Lead Plated. .625 15.88 .937 23.80 (7.92) 6-32 UNC-2A 3 Studs * .375 (9.52) 1.00 (25.4) .047 (1.20) 1.015 (25.78) 1.015 (25.79) 1.396 (35.46) 1.446 (36.73) 1.051 (25.79) 1.051 (25.79) 1.718 Max. (43.64) 26 .040 (1.02) .687 (17.44) .343 (8.71) .160 (4.06) .687 (17.44) .160 (4.06) *Metric threads available, To specify use M in place of W SERIES FCA-410 Tyco Electronics Mid-Range Military/Aerospace Relays 10 AMPERES, 4PDT TERMINALS CONTINUED .270 (6.86) .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket +X1 .062 - .001Dia. Pin (1.57 +- .05 ) 14 Plcs. .02 -X2 BLUE BEAD + .002 .062 - .001Dia. Pin (1.57 +- .05 ) 14 Plcs. .02 + .002 BLUE BEAD BLUE BEAD -X2 .270 (6.86) m .270 (6.86) CODE "G" Circuit Board Pins- 28 VAC Coils CODE "F" Circuit Board Pins-115 VAC Coils -X2 + .002 .062 - .001Dia. Pin (1.57 +- .05 ) 14 Plcs. .02 +X1 co CODE "E" Socket Pins- 28 VAC Coils +X1 s. TERMINAL WIRING D & F PIN TERMINAL E & G PIN TERMINAL 115 VAC COILS 28 VAC COILS 2 3 2 3 1 1 D D C + B B A X1 + A X1 + BLUE BEAD X2 C B A X1 + A AC B X1 A BLUE BEAD BLUE BEAD X2 C AC B co BLUE BEAD + po C + m C ne nt A & B PIN TERMINAL C HOOK TERMINAL TRANSIENT ALL DC COILS ALL AC & DC COILS SUPPRESSION CIR. 3 1 X2 2 3 3 1 X2 2 1 X2 2 D D D X1 BLUE BEAD TERMINAL LAYOUT NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. lin e .600 (15.24) -X2 .400 (10.16) on Diodes used in transient suppression and in AC rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. .200 (5.08) .600 (15.24) +X1 Terminal designations are for reference only and do not appear on the header. .400 (10.16) BLUE BEAD .200 (5.08) HOW TO ORDER FCA-415FCA-410 A Y 4 (EXAMPLE) RELAY TYPE TERMINALS (Socket Pins0 ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). NOTE: Only DC coil models are QPL Approved 27