M83536/6-024M

SERIES FCB-405 Tyco Electronics Mid-Range Military/Aerospace Relays 5 AMPERES, 4PDT VE3D6 O R P L AP -R-835 ● HERMETICALLY SEALED ● ALL WELDED CONSTRUCTION ● BALANCED FORCE ● PERMANENT MAGNET DRIVE ● CONTACTS RATED LOW LEVEL QPalified to MIL Qu nt s. co m TO 5 AMPS ● 28 VDC AND 115/200 VAC 400 Hz 3 PHASE ● WEIGHT .93 OUNCES MAX. ( 26.4 GRAMS) m po ne The Series FCB-405 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: lin e co FCB-205: 5 AMP DPDT RELAY FCB-310: 10 AMP 3PDT RELAY on CONTACT RATING-AMPERES Ratings Are Continuous Duty TYPE OF LOAD Resistive Inductive Motor Lamp LIFE (MIN.) CYCLES X 103 28 VDC 5 3 2 1 100 20 100 100 115VAC 400HZ 115/200VAC 400Hz-30 5 5 3 1 5 5 3 1 Low Level Switching Capability: With contacts operating a load of 10 to 50 microamperes at 10 to 50 millivolts, the contact resistance miss detection level shall be 100 ohms max. Cycling rate is 1 to 12 per second, for 100,000 operations. OVERLOAD CURRENT 20 AMPS DC, 30 AMPS 400HZ RUPTURE CURRENT 25 AMPS DC, 40 AMPS 400HZ CONTACT MAKE BOUNCE 1.0 MILLISECOND AT NOMINAL VOLTAGE MAX. CONTACT DROP AT 5 AMPS: INITIAL 0.100 VOLTS. END OF LIFE 0.125 VOLTS 42 SERIES FCB-405 Tyco Electronics Mid-Range Military/Aerospace Relays 5 AMPERES, 4PDT COIL DATA 6 12 28 28 48 25 Ω 100 Ω 400 Ω 400 Ω 1275 Ω DC DC DC DC DC 4.5 9.0 18.0 18.0 36.0 0.3 0.75 1.5 1.5 2.5 2.5 4.5 7.0 7.0 14.0 co 1 2 3 4 (A) 5 OVER TEMPERATURE RANGE MUST HOLD VOLTAGE (C) DROPOUT OR PICKUP OR BELOW VOLTS ABOVE VOLTS m COIL CODE DC RES. (B) FREQ. HZ NOMINAL VOLTAGES co lin e TEMPERATURE RATING: ALTITUDE: SHOCK:* m GENERAL SPECIFICATIONS po ne nt s. A. CODE 4 COILS HAVE BACK EMF SUPPRESSION D. MAX. OVER-VOLTAGE: 6 & 12 VDC COILS 120% OF TO 42 VOLTS MAX. NOMINAL; ALL OTHERS 110% OF NOMINAL. B. DC COIL RESISTANCE ± 10% AT 25˚C; C. RELAY WILL STAY IN PICKED-UP STATE DOWN TO MUST HOLD VOLTAGES SHOWN. NOTE: Only DC Coil Models are QPL Approved. on VIBRATION, SINUSOIDAL:* VIBRATION, RANDOM: * DIELECTRIC STRENGTH AT SEA LEVEL: Z, & Y ENCLOSURES W, X & M ENCLOSURES T ENCLOSURE (IN TRACK) Z, & Y ENCLOSURES W, X & M ENCLOSURES T ENCLOSURE (IN TRACK) Z, & Y ENCLOSURES T, W, X & M ENCLOSURES ALL CIRCUITS TO GROUND AND CIRCUIT TO CIRCUIT. COIL TO GROUND DIELECTRIC STRENGTH AT 80,000 FEET: INSULATION RESISTANCE: -70˚C TO + 125˚C 300,000 FEET 200 g FOR 6 mS 100 g FOR 6 mS 50 g FOR 11 mS 30 g 70-3000Hz 20 g 70-3000Hz 20 g500-3000 Hz 0.4 g2/Hz 50-2000Hz 0.2 g2/Hz 50-2000Hz 1000 V rms 1000 V rms 250 V rms 100 MΩ MINIMUM INITIAL (500 VDC) AFTER LIFE OR ENVIRONMENTAL TESTS 50 MΩ MINIMUM OPERATE TIME AT NOMINAL VOLTAGE: 6 ms OR LESS RELEASE TIME AT NOMINAL VOLTAGE: 6 ms OR LESS * Max. contact opening under vibration or shock 10 microseconds 43 SERIES FCB-405 Tyco Electronics Mid-Range Military/Aerospace Relays 5 AMPERES, 4PDT Below are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ± .010 and (Millimeters ± .25). TERMINALS .040 ±.002Dia. Pin (1.02 ±.05 ) 14 Plcs co .170 (4.32) .040 ± .001Dia. Pin (1.02 ± .02) 14 Plcs -X2 .300 (7.62) -X2 +X1 +X1 ne BLUE BEAD BLUE BEAD .080 (2.03) ± .005 (± .13) CODE "Z" .640 Max. (16.26) Code "T" used only with track-mounted Sockets. Requires code "A" pin terminals. Gasket is included in the socket assembly. lin e ± .005 (± .13) on .810 Max. (20.37) .430 (10.92) .810 Max. (20.37) co .158 **± .005 (4.01) (± .13) .110 (2.79) ± .005 (± .13) All Enclosures have cupro-Nickel cans bright acid tin/lead plated after assembly to terminal headers. Dimensions: Inches ± .010 (mm ± .25) .810 Max. (20.37) .055 ± .005 (1.38) (± .13) BLUE BEAD m .640 Max. (16.26) CODE "Y" .810 Max. (20.37) CODE "W" ** Measured from surface of header CODE "X" .141 TYP (3.58) .065 Dia. typ (1.65) .040 ±.002Dia. Pin (1.02 ±.05 ) 14 Plcs +X1 ENCLOSURES M83536/6-025 (REFERENCE ONLY) po CODE "T" .300 (7.62) nt s. -X2 HOOK TERMINALS TIN/LEAD PLATED m PIN TERMINALS TIN/LEAD PLATED PIN TERMINALS ARE GOLD PLATED .050 ± .005 (1.27 ± (3) Silicone Rubber Gasket .170 (4.32) CODE "C" Solder Hook Terminals CODE "B" Solder Pin Terminals CODE "A" Socket Pins - All DC Coils 1.078 (27.38) 1.062 (26.92) .640 Max. (16.26) .133 typ (3.38) .405 (10.29) .810 Max. (20.37) 1.078 (27.38) 1.062 (26.92) .141 (3.58) .810 Max. (20.37) FULL R 8 PLCS .025 (.64) .810 Max. (20.37) .810 Max. (20.37) .600 (5.24) 1.280 (32.51) .810 Max. (20.57) .025 (.64) .640 Max. (16.26) .500 (12.70) .250 (6.35) .156 (3.96) 1.280 (32.51) FULL R 6 PLCS .224 Dia (5.69) .133 typ (3.38) 4-40 UNC-2A 3 Studs * .500 (12.7) .712 (18.0) .250 (6.35) .500 (12.70) .375 (9.52) ± .031 ± (.79) .032 (.79) .640 Max. (16.26) .810 Max. (20.37) *Metric threads available,To specify use M in place of W 44 SERIES FCB-405 Tyco Electronics Mid-Range Military/Aerospace Relays 5 AMPERES, 4PDT TERMINAL WIRING DC COILS WITH TRANSIENT SUPPRESSION - 3 X2 2 1 D - 3 X2 C + + 1 D C co s. X1 + B 2 m DC COILS A X1 BLUE BEAD B + A ne nt BLUE BEAD TERMINAL LAYOUT po NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. co m Diodes used in transient suppression and in AC rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header. .450 (3.81) .150 (3.81) -X2 .150 (3.81) .300 (7.62) .450 (11.43) +X1 on lin e BLUE BEAD HOW TO ORDER FCB-405-A Y 4 (EXAMPLE) RELAY TYPE TERMINALS (Socket Pins) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). NOTE: Only DC coil models are QPL Approved 45