MPT30C16RJ

Thick Film Power Resistor Type MPT Series Key Features Small Size TO220 and TO247 Easy to mount Isolated moulded case Non Inductive High Power – TO220 to 50W when mounted on suitable heatsink TO247 to 100W when mounted on suitable heatsink The MPT Resistor series are a range of T0220 and TO247 packaged, low inductance thick film power resistors. This small size, high power device with 5 models are ideally suited to applications where high power dissipation yet small size are key design requirements. The MPT Resistor series are the ideal solution for small snubber circuits, the output side of high speed pulse generators and low inductive resistor requirements in switch mode power supplies. Characteristics – Electrical Package Size Resistance Range Rated Power (with Heatsink) Rated Power (in free air) Maximum Operating Voltage Dielectric Strength Insulation Resistance Operating Temperature Package Size Resistance Range Rated Power (w / Heatsink) Rated Power (in free air Maximum Operating Voltage Dielectric Strength Insulation Resistance Operating Temperature 1773180 Rev. C 05/2018 Dimensions in millimetres unless otherwise specified MPT20 TO220 R05 ~ 1M0 20W 3W@25°C 350V MPT50 TO220 R10 ~ 10K 50W 3W@25°C 350V MPT30 TO220 R05 ~ 100K 30W 2.25W@25°C 420V 1800VAC 10GΩ min. -65°C~150°C MPT50H TO220 R10 ~ 10K 50W 2.25W@25°C 420V 1800VAC 10GΩ min. -65°C ~ 150°C Dimensions Shown for reference purposes only. Specifications subject to change MPT35 TO220 R05 ~10K 35W 2.5W@25°C 350V MPT100 TO247 R05 ~ 100K 100W 3.5W@25°C 700V -65°C ~175°C For Email, phone or live chat, go to: www.te.com/help Thick Film Power Resistor TCR / Tolerance Value Chart 0.5% 1% 5% 10% R05 ~ 1R0 1R1 ~ 3R0 3R3 ~ 10R 11R ~1M0 R05 ~1R0 1R1 ~ 3R0 3R3 ~10R 11R ~100K R05 ~ R91 1R0 ~ 10R 11R ~ 10K 1R0 R10 ~ 1R0 1R1 ~3R0 3R3 ~ 10R 11R ~10K 1R0 R10 ~1R0 1R1 ~ 3R0 3R3 ~ 10R 11R ~ 10K R05 ~ 1R0 1R1 ~ 3R0 3R3 ~ 10R 11R ~ 100K - MPT20 MPT30 MPT35 MPT50 MPT50H MPT100 - - - - - - TCR Unspecified 300PPM 100PPM 50PPM Unspecified 300PPM 100PPM 50PPM Unspecified 100PPM 50PPM Unspecified 300PPM 100PPM 50PPM Unspecified 300PPM 100PPM 50PPM Unspecified 300PPM 100PPM 50PPM Characteristics – Environmental Test Item Temperature Coefficient of Resistance (T.C.R.) Short Time Overload Requirement As Spec. Load Life Damp Heat with Load ΔR±1.0% ΔR±0.5% Solderability Thermal Shock Terminal Strength Vibration, High Frequency 90% min. coverage ΔR±0.3% ΔR±0.2% ΔR±0.2% ΔR±0.3% Test Method Referenced to 25°C, ΔR taken at +105°C 2 times rated power with applied voltage not to exceed 1.5 times Maximum continuous operating voltage for 5 seconds 2,000 hours at rated power 40±2°C, 90~95% R.H., RCWV for 1000 hrs ith 1.5 hrs ON and 0.5 hrs OFF 245±5°C for 3 seconds -65°C~150°C, 100 cycles (Pull Test) 2.4N 20g peak Lead Material: Tinned Copper For Models with fixing hole, maximum torque 0.9Nm The Case Temperature is to be used for the Definition of the Applied Power Limit The Case Temperature Measurement must be made with a Thermocouple Contacting the Center of the Component mounted on the Designed Heat Sink. Thermal Grease should be Applied Properly RCWV Rated continuous orking oltage = √ P*R or Max. Operating oltage hiche er is lower 1773180 Rev. C 05/2018 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Thick Film Power Resistor Derating Curve Construction and dimensions MPT20 1 2 1773180 Rev. C 05/2018 Dimensions in millimetres unless otherwise specified Alumina Substrate Resistor Layer Dimensions Shown for reference purposes only. Specifications subject to change 3 4 Lead Moulding For Email, phone or live chat, go to: www.te.com/help Thick Film Power Resistor MPT30 1 2 Alumina Substrate Resistor Layer 3 4 Lead Moulding 1 2 3 Flange Alumina Substrate Resistor Layer 4 5 Lead Moulding MPT35 1773180 Rev. C 05/2018 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Thick Film Power Resistor MPT50 1 2 Alumina Substrate Resistor Layer 3 4 Lead Moulding 1 2 Alumina Substrate Resistor Layer 3 4 Lead Moulding MPT50H 1773180 Rev. C 05/2018 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Thick Film Power Resistor MPT100 1 2 Alumina Substrate Resistor Layer 3 4 Lead Moulding Packaging Model MPT20 MPT30 MPT35 MPT50 MPT50H MPT100 Net Weight (1000 pieces) 1290g 1155g 1902g 1290g 2770g 3381g Tube 50 pieces 50 pieces 50 pieces 50 pieces 50 pieces 35 pieces How To Order MPT 35 C 100R J Common Part Power Rating on Heatsink @25°C Temp. Coefficient of Resistance Resistance Value Tolerance MPT 1773180 Rev. C 05/2018 20 – 20W 30 – 30W 35 – 35W 50 – 50W 50H – 50W 100 – 100W Dimensions in millimetres unless otherwise specified X – unspecified C – 50PPM A – 100PPM S – 200PPM T – 300PPM 0.1 ohm (100 milliohms) R10 1 ohm (1000 milliohms) 1R0 1K ohm (1000 ohm) 1K0 Dimensions Shown for reference purposes only. Specifications subject to change D - 0.5% F - 1% J - 5% K - 10% For Email, phone or live chat, go to: www.te.com/help