MRS33KBF

SMD Precision Thin Film Network Type MRS Series Key Features I Suitable for tight spaces I High precision thin film I Wide value range I Lower placement costs I Range of stabilities I Low cost in volume I High reliability design I RoHS compliant component compatible with lead (Pb) free soldering techniques Applications I Voltage divider I Feedback circuits I Signal conditioning The MRS series is an entirely new chip network utilising nickel chrome sputtering on high purity alumina. This network has been designed for high volume applications and is offered with 4 isolated resistors on a single substrate (4 x 0603 resistors) at 0.1% with convex terminals. A wide value range and alternative TCRs (Temperature Coefficient of Resistance) make this a most versatile resistor solution. Characteristics - Electrical Rated Power at 70°C: 0.0625W Resistance Range Ω Min: 100 100 Resistance Range Ω Max: 2K0 33K Resistance Tolerance: ±0.1%, ±0.5%, ±1% Temperature Coefficient of Resistance (ppm/°C): ±10 ±15 ±25 Selection Series: ±50 E24 Maximum Operating Voltage: 50V Maximum Overload Voltage: 100V Operating Temperature Range: -55 to +155°C Operating Voltage=√(P*R) or max. operating voltage listed above, whichever is lower Overload Voltage=2.5*√(P*R) or max. overload voltage listed above, whichever is lower Characteristics - Environmental Requirement Item Test Method Tol. ≤ 0.25% Temperature Coefficient of Resistance (T.C.R.): Tol. > 0.25% MIL-STD-202F Method 304 +25/-55/+25/+125/+25°C As specified Short Time Overload: ΔR±0.25% ΔR±0.5% Insulation Resistance: JIS-C-5201-1 5.5 RCWV*2.5 or max. overload voltage for 5 seconds MIL-STD-202F Method 302 Apply 100VDC for 1 minute 1000MΩ Endurance: ΔR±0.25% ΔR±0.5% MIL-STD-202F Method 108A 70±2°C, max. working voltage for 1000hrs with 1.5hrs “ON” and 0.5 hrs “OFF” Damp Heat with Load: ΔR±0.25% ΔR±0.5% MIL-STD-202F Method 103B 40±2°C, 90~95% R.H. max. working voltage for 1000hrs with 1.5hrs “ON” and 0.5 hrs “OFF” Bending Strength: ΔR±0.25% ΔR±0.5% JIS-C-5201-1 6.1.4 Bending amplitude 3mm for 10 seconds ΔR±0.5% MIL-STD-202F Method 210E 260±5°C for 10 seconds Solderability: 95% min. coverage Resistance to Soldering Heat: ΔR±0.25% Dielectric Withstand Voltage: MIL-STD-202F Method 208H 245±5°C for 3 seconds MIL-STD-202F Method 301 max. overload voltage for 1 minute 100V Thermal Shock: ΔR±0.25% ΔR±0.5% MIL-STD-202F Method 107G -55°C ~150°C, 100 cycles Low Temperature Operation: ΔR±0.25% ΔR±0.5% JIS-C-5201-1 7.1 1 hour, -65°C, followed by 45 minutes of RCWV Storage Temperature: 25±3°C; Humidity < 80%RH 1773252 CIS BI 06/2011 Dimensions are in millimeters and inches unless otherwise specified. Values in brackets are standard equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, go to: te.com/help SMD Precision Thin Film Network Type MRS Series Derating Curve 100 Power Ratio (%) 80 60 40 20 0 0 20 40 60 80 100 120 140 160 180 Ambient Temperature (°C) Dimensions Type MRS No. of Resistors L W H Dimension A B C Y Weight (g) (1000 pcs) 4 3.20 ±0.15 1.60 ±0.15 0.55 ±0.10 0.50 ±0.15 0.80 ±0.05 0.30 ±0.15 0.30 ±0.15 8.22 Construction Recommend Land Pattern Circuit Diagram Type A B C I P MRS 2.85 3.10 0.45 0.80 0.80 1773252 CIS BI 06/2011 Dimensions are in millimeters and inches unless otherwise specified. Values in brackets are standard equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, go to: te.com/help SMD Precision Thin Film Network Type MRS Series Paper Tape Specification Type A B W E F P0 P1 P2 øD0 T MRS 1.95 ±0.1 3.50 ±0.1 8.0 ±0.2 1.75 ±0.1 3.5 ±0.05 4.0 ±0.1 4.0 ±0.05 2.0 ±0.05 1.5 +0.1/-0 0.85 ±0.1 Packaging Type Packaging-Quantity Tape Width Reel Diameter øA øB øC W T MRS Paper-5K 8mm 7 inch 178.5 ±1.5 60 +1/-0 13.0 ±0.2 9.0 ±0.5 12.5 ±0.5 Marking Type 100R 2K2 0K 22K 33K MRS 1000 2201 1002 2202 3302 How to Order MRS 100R B F Common Part Resistance Value Tolerance TCR 100R (100 Ohms) MRS - Precision thin film chip network 1K0 (1000 Ohms) 10K (10,000 Ohms) B - ±0.1% D - ±0.5% F - ±1% C - ±10ppm/°C D - ±15ppm/°C F - ±25ppm/°C G - ±50ppm/°C 100K (100,000 Ohms) TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Other logos, product and Company names mentioned herein may be trademarks of their respective owners. While TE has made every reasonable effort to ensure the accuracy of the information in this datasheet, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this datasheet are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.