NETM1000-6-0-SP

NETM1000 Table 1: Dimensions Inside Diameter (D) in. mm. .118 ± .02 3 ± 0.5 .157 ± .02 4 ± 0.5 .197 ± .02 5 ± 0.5 .236 ± .02 6 ± 0.5 .315 ± .02 8 ± 0.5 .394 ± .02 10 ± 0.5 .472 ± .02 12 ± 0.5 .551 ± .02 14 ± 0.5 Size 3 4 5 6 8 10 12 14 Wall Thickness (W) in. mm. .020 ± .004 0.5 ± .1 .020 ± .004 0.5 ± .1 .020 ± .004 0.5 ± .1 .020 ± .004 0.5 ± .1 .020 ± .004 0.5 ± .1 .020 ± .004 0.5 ± .1 .020 ± .004 0.5 ± .1 .020 ± .004 0.5 ± .1 Table 2: Properties Property Dimensions Tensile Strength Elongation Longitudinal Change Low Temperature Flexibility 4 Hours at -55± 3C Heat Shock 4 hours at 250± 3C Heat Age, 168 hours at 175± 3C followed by tests for Tensile Strength Elongation Volume Resistivity Flammability Unit Inches (mm) PSI (MPa) Percent Percent -- Requirement Table 1 1500 (10.3) minimum 150 minimum -10 maximum No cracking Test Method ASTM D 2671 ASTM D 2671 20 inches/minute ASTM D 2671 Note 1 -- No dripping, flowing or cracking ASTM D 2671 PSI (MPa) Percent ohm-m -- ASTM D 2671 20 inches/minute ASTM D 2671 ASTM D 2671 Procedure C Voltage Withstand Volts 1500 (10.3) minimum 150 minimum 103 minimum No flaming or glowing longer than 1 minute from any flame application. 25% max. flag burn. No burning of cotton. 1000 volts for 1 minute, minimum ASTM D 2671 Customer Drawing ©2015 Tyco Electronics Corporation. All Rights Reserved Title: NETM1000 Tubing Tyco Electronics reserves the right to amend this drawing at any time. Users should evaluate the suitability of the product for their application Cage Code: Scale: Size: 06090 None A Document No : NETM1000 Rev. Date: Rev.: Sheet: 23-Oct-2015 B 1 of 2 If this document is printed it becomes uncontrolled. Check for the latest revision. Properties, continued Property Fluid Resistance 1 Hour at 50C in Battery Acid followed by test for: Weight Increase 24 Hour at 23C in Gasoline Diesel Fuel Transmission Oil Power Steering Fluid followed by test for: Weight Increase 1 Hour at 50C in Motor Oil 15W/40 Brake Fluid, DOT 4 followed by test for: Weight Increase 1 Hour at 23C in Antifreeze 50/50 followed by test for: Weight Increase Unit Requirement Percent 15 maximum Percent 15 maximum Percent 15 maximum Percent 15 maximum Test Method Note 2 Note 1: Test three specimens of tubing for low temperature flexibility as follows: Slide the tubing onto a stranded AWG wire (nearest AWG which will fit inside the tube). Condition the specimens and a mandrel, selected from Table 2, in a cold chamber for 4 hours at -55 ± 3C (-67 ± 5F). After completion of the conditioning period and while still in the cold chamber at the specified temperature, bend the specimen around the mandrel through not less than 360 degrees in 10 ± 2 seconds. Visually examine the tubing for cracks. Note 2: Six specimens, three 6-inch (150-mm) tubing specimens, which shall be weighed prior to immersion and shall be immersed in each of the test fluids listed at the temperature specified. The volume of the fluid shall not be less than 20 times that of the specimens. After conditioning, all the specimens shall be lightly wiped and air dried for 30 to 60 minutes at 23 ± 3C (73 ± 5°F). The three specimens shall be reweighed after immersion and the weight change calculated as a percentage. Table 3: Mandrel Dimensions for Bend Testing Size Mandrel Diameter mm 7.9 ± 0.05 9.5± 0.08 3 to 6 inclusive 8 to 14 inclusive Rev. Date: Rev.: 23-Oct-2015 B If this document is printed it becomes uncontrolled. Check for the latest revision. in. 5/16 ± 0.002 3/8 ± 0.003 Document No. NETM 1000 Sheet: 2 of 2