PB6B2RS2M1CAL00

Sealed Pushbutton Switches IP68 Sub-Miniature Pushbutton Switches Key Features • • • • • • • IP68 Rated (1Meter, 60 Minutes) Normally Open and Normally Closed Versions Various Cap Options LED illuminated flat cap versions Various cap and color illuminations Leaded options for ease of installation LED illumination technology for long-term reliability TE Connectivity’s Sub-Miniature Pushbutton range is a portfolio of high quality,IP68 rated switches that comprises various cap styles and LED illumination options. These Pushbutton Switches are offered in High Cap, Round Cap, Flat Cap, and LED Flat Cap actuators. For ease of installation without the need of soldering, they are also available with 500mm leaded options. As they are available in 5 different cap colors, including black, Red, Yellow, Green, and Blue as well as multi-color LED options for the flat cap, these switches can be used in a wide variety of applications. Applications Benefits • • • • • Industrial Equipment Instrumentation Communication Equipment Control Equipment • Ease of installation with available solderable or 500mm leaded terminations Various colored caps for easy visibility Switch Function / Schematic SWITCH FUNCTION POS. 1 POS. 2 SCHEMATIC POS. 2 NO. POLES MODEL NO. SP PB6 OFF MOM(ON) OPEN CLOSE SP PB7 ON MOM(OFF) CLOSE OPEN POS. 1 MOM = MOMENTARY Document #: 0-2329328-1 Version Date: 03-2018 Dimensions in millimetres (inches) unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Sealed Pushbutton Switches Specifications MAX. CURRENT/VOLTAGE RATING WITH RESISTIVE LOAD: INITIAL CONTACT RESISTANCE: INSULATION RESISTANCE: DIELECTRIC STRENGTH: ELECTRICAL LIFE AT FULL LOAD: OPERATING TEMPERATURE: PANEL THICKNESS: TOTAL TRAVEL: OPERATING FORCE: CONTACT BOUNCE: MECHANICAL LIFE: TORQUE: DEGREE OF PROTECTION: MANUAL SOLDERING: WAVE SOLDERING: 400 mA 32 VAC – 200 mA 50 VDC – 125 mA 125 VAC Without leads: 50mΩmax. Leaded: 100mΩmax. * Resistance of the wire not included 1GΩmin.at 500 VDC 1,500 VAC RMS 500,000 cycles -30°C to 85°C 1.5 (.059) to 4 (.157) 1.5 (.059) 3 to 6N 10 ms. 1,000,000 cycles 0.5 Nm max. applied to nut IP68 Use soldering iron of 30 watts, controlled at 350°C approximately 5 seconds while applying solder Recommended Soldering Temperature:260 + 5°C *Ambient temperature of the soldered surface of PC board. 110°C Max. Duration of solder Immersion: Max 5 sec (PCB is 1.6mm) Materials CAP: Polyamide 6/6 PLUNGER: PB6:PC / PB7: Polyamide 6/6 RUBBER: Silicone BUSHING: POLYAMIDE 6/6 CASE: Diallyl phthalate (DAP)(UL94V-0) TERMINAL/CONTACT: Copper Alloy, Gold over Silver plated Hardware M12 Nut Lock Washer 16.00 (.630) O-Ring Ø13.50 (ø.532) Ø15.90 14.00 (ø.625) (.551) 1.20 (.047) 2.50 (.098) Document #: 0-2329328-1 Version Date: 03-2018 Dimensions in millimetres (inches) unless otherwise specified 1.0 THK (.039) Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Sealed Pushbutton Switches Bushing Type B2 Panel Cut-Out 7.30 (.287) THICKNESS 1.5 to 4.0mm 10.70 (.421) +0.05 12.90 -0.03 +.002 (.508 -.001 ) Ø 17.50 (.689) +0.00 Ø 13.60 -0.10 +.000 (.534 -.004 1.20 (.047) 5.00 (.197) ) Cap Options High without LED Round without LED Flat Ø 12.00 (.472) (.472) 4.7 (.185) Ø 12.00 2.59 (.102) Ø 12.00 2.0 (.078) (.472) Termination Options M1 Solder Lug (PB6) 3.50 (.138) M1 Solder Lug (PB7) 0.40 (.016) 2.80 (.110) 5.08 (.200) M2 Solder Lug (PB6) 0.40 (.016) 5.08 (.200) 0.40 (.016) Dimensions in millimetres (inches) unless otherwise specified 2.80 (.110) 3.40 (.134) 0.40 (.016) 0.50 (.020) 2.80 (.110) 5.00 (.197) 0.20 (.008) 0.40 (.016) 5.08 (.200) M4 PC Thru-hole (PB6) 8.20 (.323) 5.08 (.200) Document #: 0-2329328-1 Version Date: 03-2018 2.80 (.110) M3 Solder Lug (PB6) 5.50 (.217) 2.80 (.110) 3.40 (.134) M1 Solder Lug (PB6, with LED) 0.40 (.016) 3.50 (.138) 1.00 (.039) 5.08 (.200) 5.08 (.200) Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help 0.40 (.016) Sealed Pushbutton Switches Wire Option WIRE LENGTH DIM ''L" Code S500 Length Wire S500 500mm Lead 12.70 (.500) Y500 500+10 (19.7+ .394) 500+10 (19.7+ .394) TERMINAL 1 BLACK TERMINAL 2 BLACK Code DIM “L” S500 500+10 NON (19.7- LED + .394) DESCRIPTION WIRE+COLOR Y100 500+10 (19.7 .394) Ø 10.50 (.413) Y500 500mm Lead with Heat Shrink DESCRIPTION TERMINAL 1 TERMINAL 2 LED+ LED- 10.0 (.394) WITH LED WIRE COLOR BLACK BLACK RED GREEN *Multi-wire lead AWG20, section 0.6mm , UL approved PB6 M1 10.70 (.421) 1.20 (.047) Ø 17.50 (.689) 2.80 (.110) Ø 12.00 (.472) 3.50 (.138) 2.0 (.078) PB7 M1 10.70 (.421) 1.20 (.047) Ø 17.50 (.689) 0.40 (.016) 5.08 (.200) 12.90 5.00 (.508) (.197) 2.80 (.110) Ø 12.00 (.472) 3.40 (.134) 2.0 (.078) 5.00 (.197) PB6 M1 with LED 1.20 (.047) Ø 17.50 (.689) 0.50 (.020) 2.80 (.110) Ø 12.00 (.472) 2.0 (.078) 5.00 (.197) 15.10 (.595) 0.40 (.016) 5.08 (.200) 13.40 (.527) 0.40 (.016) 3.40 (.134) 10.70 (.421) 5.00 (.197) 5.08 (.200) 0.40 (.016) . Document #: 0-2329328-1 Version Date: 03-2018 Dimensions in millimetres (inches) unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help Sealed Pushbutton Switches How To Order Model NO. Bushing Cap Shape Cap Contact Color Termination Material Seal LED Color Model NO. PB6 OFF-MOM (ON) PB7 ON -MON(OFF) Wire S500 500mm Lead Y500 500mm Heat Shrink Lead Bushing B2 Threaded bushing LED Color L00 Without LED L01 White L03 Red L05 Yellow L06 Green L07 Blue Cap Shape & Appearance FM Flat Cap Matte (with and without LED) RS Round Cap Shiny (without LED) HS High Cap Shiny (without LED) *Only flat cap available with LED Cap Color 2 Black 3 Red 5 Yellow 6 Green 7 Blue Seal A Sealed Termination M1 3.50 High, Solder Lug (PB6 only, Non-LED) 3.40 High, Solder Lug (with LED and PB7 Non-LED) M2 5.50 High, Solder Lug, (PB6 only, Non-LED) M3 8.20 High, Solder Lug, (PB6 only, Non-LED) M4 3.50 High, PC Thru-Hole, (PB6 only, Non-LED) Document #: 0-2329328-1 Version Date: 03-2018 Wire Dimensions in millimetres (inches) unless otherwise specified *Only flat cap available with LED Contact Material & Finish C Gold Over , Gold over Silver Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help