PD10AC57

KILOVAC 28 - 1800 Vdc High Voltage Relays PD10 Make & Break Load Switching Product Facts n Excellent for control applications n PCB and panel mountings n Rugged design for the most demanding applications, including seismic shock n Small size and weight n Low power consumption n No heat sinks required n Vacuum-sealed; can operate in explosive and harsh environments n 2000 V isolation across open contacts n Vacuum dielectric for power switching For factory-direct application assistance, dial 800-253-4560, ext. 2055, or 805-220-2055. Panel mount version shown above is applicable to both PD5 and PD10. For PD10, the two power terminals are .064" (1.63) diameter. Refer to PD5 for PCB mount dimensions. Product Specifications Contact Arrangement — PD10A — SPST-NO PD10B — SPST-NC PD10P*** — SPST-Latching Contact Form — PD10A — A** PD10B — B** PD10P*** — P** Rated Resistive Load @ 320 Vdc — 10 A Continuous Current Carry, Max. @ 85°C — PD10A and PD10B — 25 A PD10P*** — 30 A Overload @ 320 Vdc, (Make/Break) — 20 A Contact Ratings* Life, (Mechanical/Rated Load) — PD10A and PD10B — 500k cycles/10k cycles PD10P*** — 7,000 cycles Contact Resistance, Max., End of Life — PD10A and PD10B — 0.030 ohm PD10P*** — 0.030 ohm Dielectric at Sea Level — Power Terminals to Coil and All Other Points — PD10A and PD10B — 1,800 Vrms PD10P*** — 2,000 Vrms Shock, 11ms, 1/2 Sine (Peak) — 25 g Vibration, Sinusoidal (55-2000 Hz, Peak) — 5 g Operating Ambient Temperature Range — PD10A and PD10B — -40°C to +85°C PD10P*** — -35°C to +65°C Operate Time, Max., Including Bounce @ 25°C — PD10A and PD10B — 10 ms PD10P*** — 6 ms Release Time, Max., Including Bounce @ 25°C — PD10A and PD10B — 10 ms PD10P*** — 6 ms Insulation Resistance @ 500 Vdc, Min. — Initial/End of Life — 100 mohm/50 mohm Weight, Nominal — 71 g (.156 lb) Notes: **Contact TE for availability of other contact forms ***Not available in package shown, package is the same as the K41P. Ordering Information PD10 A A 5 7 Sample Part Number 䊳 Series: *Based on extrapolated data. Since each application is unique, user is encouraged to verify rating in actual application. The load terminals should always be connected as follows: Common Contact (A2) positive; Other Contact negative. Coil Data Nominal Volts DC Max. Coil Voltage Pickup, Max. @ 85°C Hold, Min. @ 85°C Dropout, Min. @ -40°C Coil Resistance (±10%) 12 Vdc 14 Vdc 8 Vdc 3.3 Vdc .5 Vdc 70 Ω Ratings listed are for 25°C, sea level conditions 24 Vdc 28 Vdc 16 Vdc 10 Vdc 1 Vdc 290 Ω 125 Vdc 130 Vdc 80 Vdc 33 Vdc 5 Vdc 4700 Ω Contact Form: A = SPST-NO B = SPST-NC P = SPST-Latching Coil Voltage: 2 = 12 Vdc, PCB Version 3 = 24 Vdc, PCB Version 5 = 125 Vdc, PCB Version A = 12 Vdc, Panel Mount Version B = 24 Vdc, Panel Mount Version C = 125 Vdc, Panel Mount Version Power Terminals: 3 = PCB Solder Connection 5 = Stud Terminal, Panel Mount Mounting: 5 = PCB Mount 7 = Panel Mount 7–56 Catalog 5-1773450-5 Revised 3-13 www.te.com Dimensions are shown for reference purposes only. Specifications subject to change. Dimensions are in millimeters unless otherwise specified. USA: +1 800 522 6752 Asia Pacific: +86 0 400 820 6015 UK: +44 800 267 666 For additional support numbers please visit www.te.com