PDT-48-00

7 SOLID CONTACT PART NUMBER E 0460-204-12** 0460-211-12** 0460-220-12** 0460-235-12** 0460-258-12** 0462-203-12** 0462-210-12** 0462-214-12** 0462-215-12** 0460-256-12** D C 6 SIZE TYPE 12 PIN 12 PIN 12 PIN 12 PIN 12 PIN 12 SOC 12 SOC 12 SOC 12 SOC 12 PIN 0460-215-16** 0462-209-16** 16 PIN 16 SOC 0460-002-16** 0460-202-16** 0460-211-16** 0460-230-16** 0460-235-16** 0460-247-16** 0462-004-16** 0462-007-16** 0462-201-16** 0462-214-16** 0462-221-16** 0462-222-16** 16 PIN 16 PIN 16 PIN 16 PIN 16 PIN 16 PIN 16 SOC 16 SOC 16 SOC 16 SOC 16 SOC 16 SOC 0462-001-16** 16 SOC 0462-223-16** 16 SOC 0460-010-20** 0462-005-20** 20 PIN 20 SOC 0460-202-20** 0462-201-20** 112349 112352 B 6 20 PIN 20 SOC 12 PIN 12 SOC 0460-201-1690 0461-201-1690 8960-025-12603 8962-014-12603 8960-020-16603 8962-011-16603 16 PIN 16 SOC 12 PIN 12 SOC 16 PIN 16 SOC WIRE SIZE AWG [mm²] 5 RECOMMENDED REF. ONLY CRIMP TENSILE STRIP LENGTH INCH [mm] LBS [N] 4 3 REV CONTACT IDENTIFICATION INFO & NOTES NC DESCRIPTION DATE APPROVED 6-8-12 NEW RELEASE PER E.O. P21384 R.D.R. REVISED PER ECO-13-003161 75 [334] .222-.284 [5.64-7.21] 14 AWG 2.0 mm² 70 [311] 1.5 mm² 16 AWG 1.0 mm² 35 [156] 18 AWG 0.75 mm² 25 [111] 14 AWG 2.0 mm² 70 [311] E 0462-215-12** MARKING 1 GRAY BAND, NARROW 1 BROWN BAND, NARROW 1 BROWN BAND, BROAD JAM NUT 5 LOCATOR .222-.284 [5.64-7.21] .250-.312 [6.35-7.92] 1 GREEN BAND, BROAD 1 GREEN BAND, BROAD 3 7 1.5 mm² 16 AWG 1.0 mm² .250-.312 [6.35-7.92] 0460-002-1631 AND 0462-004-1631 MARKING 1 BLUE BAND, BROAD 18 AWG 0.75 mm² 25 [111] 20 AWG 0.50 mm² 20 [ 89] 16 AWG 1.0 mm² 35 [156] .250-.312 [6.35-7.92] 35 [156] .117-.237 [4.49-6.02] USE 2.0 mm² DIAL SET 20 [ 89] .156-.218 [3.96-5.54] 1 PURPLE BAND, BROAD 1.5 mm² 16 AWG 1.0 mm² 16 AWG 1.00 mm² 18 AWG 0.75 mm² 20 AWG 0.50 mm² 20 [ 89] 22 AWG 0.35 mm² 10 [44] 12 AWG 3.0 mm² 2.5 mm² 14 AWG 2.0 mm² 75 [334] 35 [156] 18 AWG 0.75 mm² 4.0 mm² 12 AWG 3.0 mm² 2.5 mm² 1.5 mm² 16 AWG 1.0 mm² AIR INLET 1/4" NPT 11 1 BLUE BAND, NARROW SOLID CONTACT PART NUMBER 4060-002-12** 4062-002-12** 6 WIRE SIZE AWG [mm²] SIZE TYPE 12 PIN 12 SOC .156-.218 [3.96-5.54] 4060-001-16** 4062-001-16** SLOTTED (SPLIT) PIN .222-.284 [5.64-7.21] 3 4 16 PIN 16 SOC RECOMMENDED REF. ONLY STRIP LENGTH CRIMP TENSILE INCH [mm] LBS [N] 12 AWG 3.0 mm² 2.5 mm² 75 [334] 14 AWG 2.0 mm² 70 [311] 1.5 mm² 16 AWG 1.0 mm² 35 [156] 18 AWG 0.75 mm² 25 [111] CONTACT IDENTIFICATION INFO & NOTES .250-.312 [6.35-7.92] 3 4 C .240-.302 [6.10-7.67] 13. OPTIONAL FOOT VALVE PART NUMBER: WA10A (SOLD SEPARATELY). AVAILABLE FROM: DANIELS MANUFACTURING COMPANY; 526 THORPE ROAD; ORLANDO, FL 32824-8133; PHONE: 407-855-6161. SLOTTED (SPLIT) PIN 12. OPTIONAL BASE MOUNT PART NUMBER: BM-2A (SOLD SEPARATELY). SEE SHEET 2. AVAILABLE FROM: DANIELS MANUFACTURING COMPANY; 526 THORPE ROAD; ORLANDO, FL 32824-8133; PHONE: 407-855-6161. .222-.284 [5.64-7.21] 25 [111] 75 [334] D 1 70 [311] 1.5 mm² 16 AWG 1.0 mm² 2 SELECTOR DIAL 35 [156] B 11 USE 3.0/12 SETTING FOR THIS PART WITH 4.0mm². .222-.284 [5.64-7.21] 10. 9 FOOT AIR HOSE WITH 1/4" NPT CONNECTOR SUPPLIED WITH TOOL IN A SEPARATE BAG, PART NUMBER: 12-3001. 11 9. SEE 0425-079-0000 INSTRUCTION GUIDE, SHIPPED WITH TOOL. 35 [156] 18 AWG 0.75 mm² 25 [111] 20 AWG 0.50 mm² 20 [89] 8. OVERALL TOOL LENGTH IS APPROXIMATELY 9.88 [250.82]. .250-.312 [6.35-7.92] 7 CYCLE TOOL TO OPEN INDENTERS. REMOVE LOCK CLIP. RAISE AND ROTATE DIAL TO SELECT WIRE SIZE. REPLACE LOCK CLIP. 6 WHEN ** = 31, PLATING IS GOLD. WHEN ** = 141, PLATING IS NICKEL. WHEN ** = 309, PLATING IS TIN. (CONTACT FACTORY FOR AVAILABILITY) 4 USE 2.5/14 SETTING FOR THIS PART WITH 12 AWG. SIGNATURE & DATE DR 3 USE 1.5 SETTING FOR THIS PART WITH 14 AWG. CHK 2 CAUTION: NEVER CLOSE TOOL ON GAGE G454. CLOSE TOOL FIRST AND THEN INSERT GAGE. PE 1 USE GAGE G454 IN DIAL POSITION 1.0/16 TO CHECK WEAR ANNUALLY. CHECK OFTEN IF USED FOR FREQUENT CRIMPING. NOTES: UNLESS OTHERWISE SPECIFIED 7 SYM A 12 AWG 3.0 mm² 2.5 mm² 1 REVISIONS PDT-48-00 A 5 DEPTH ADJUSTING SCREW P/N 0426-209-0000 INCLUDES JAM NUT. A 2 6 5 4 J.APOSTOL 25APR2012 D. MEYER 2/21/13 D. MEYER 2/21/13 D. MEYER 2/21/13 SCALE NONE WT TOOL, PNEUMATIC CRIMP FOR SIZE 20, 16 & 12 SOLID CONTACTS 3850 INDUSTRIAL AVE. HEMET, CA 92545 DEUTSCH INDUSTRIAL APPD 3 MATL. CODE EP ENVELOPE 2 C DWG SIZE PDT-48-00 CODE 11139 SHEET 1 1OF2 A 7 6 5 4 3 REV 2 PDT-48-00 A REVISIONS SYM A E (8.000 D DESCRIPTION DATE APPROVED SEE SHEET 1 E [203.20]) (2X (4.094 [103.98] 1 .406 ) [ 10.31 ] ) D (7.250 [184.15]) C C B (4.500 [114.30] ) B OPTIONAL BASE MOUNT A SIGNATURE & DATE DR CHK PE J.APOSTOL 25APR2012 D. MEYER 2/21/13 D. MEYER 2/21/13 D. MEYER 2/21/13 SCALE NONE WT TOOL, PNEUMATIC CRIMP FOR SIZE 20, 16 & 12 SOLID CONTACTS 7 6 5 4 3 3850 INDUSTRIAL AVE. HEMET, CA 92545 DEUTSCH INDUSTRIAL APPD NOTES: MATL. CODE EP ENVELOPE 2 C DWG SIZE PDT-48-00 CODE 11139 SHEET 1 2OF2 A