TECHNICAL DATA SHEET
RayMark Six Labels
Document number: TTDS-032
Issue: 2
Date: August 2014
MATERIAL DESCRIPTION:
Computer-printable zero halogen label material. Permanent pressure sensitive
acrylic adhesive. Thermally stabilised white polyester film with special ink
receptive latent cure epoxy coating on the label surface. After printing, the surface
is heat cured, embedding the image within a tough polymeric layer.
USE:
RayMark Six labels have outstanding abrasion and fluid resistance without the
need for an overlay. Ideal for applications where high performance variable data
labels are needed, for example in defence, marine, rail and aerospace
applications. Can be used as a wire/cable wraparound marker for substrates not
less than 6mm (0.25 inches) diameter. Not recommended for outdoor use.
PRINTING SYSTEM
Print Quality and Print Performance can only be guaranteed when specific TE
printer and ribbons are used.
The current list of printers and ribbons can be found in TE document 411-121005
‘Identification Printer Product Ribbon Matrix’
This document can be found at the TE document centre:
http://www.te.com/commerce/DocumentDelivery/DDEController
Raymark is fully supported by WINTOTAL and PrintEasy label printing software,
available from the TE product store:
http://www.te.com/en/general/label-printing-software.html
Contact a TE representative for further information
CURING CONDITIONS:
5 minutes at 150ºC (302ºF) in an air circulating oven.
SHELF LIFE/STORAGE
CONDITIONS:
Can be stored unopened for 12 months at temperatures not exceeding 35ºC
(95ºF).
Once opened, product should be stored below 25ºC (77ºF) and 80% relative
humidity and used within 6 months.
SERVICE TEMPERATURE:
Wiring marking: -40ºC to +85ºC (-40ºF to +185ºF) continuous.
Panel marking: -40ºC to +105º (-40ºF to +221ºF) continuous.
INSTALLATION TEMP:
+10C to +40C (+50F to +104F).
COLOURS:
White.
If the document is printed it becomes uncontrolled
Check with TE Connectivity (TE) for latest version
Author: L Smith
Issue date: Aug 2014
Page:
1 of 3
While TE Connectivity Ltd. has made every reasonable effort to ensure the accuracy of the information in this document, TE does
not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is
accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any
time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not
limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are for
reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE
for the latest dimensions and design specifications.
TECHNICAL DATA SHEET
RayMark Six Labels
Document number: TTDS-032
Issue: 2
Date: August 2014
Property
Test Method
Required
Fungus Resistance
BS EN 60068-2-10:2005
Print Legibility TE108-121012
Rating 1 (max)
Legible, print contrast >3
Light fastness, xenon arc
250 hour, ASTM G155-05a
Print Legibility TE108-121012
Adhesion to aluminium plate TE 108-121030
Legible, print contrast >3
20N/25mm adhesion
Continuous humidity
168h, 40ºC (104ºF)/95% RH
Print Legibility TE108-121012
Adhesion to aluminium plate TE 108-121030
Legible, print contrast >3
15N/25mm adhesion
Thermal ageing
168h at 150ºC (302ºF)
Print Legibility TE108-121012
Adhesion to aluminium plate TE 108-121030
Legible, 30N/25mm adhesion
Thermal cycling
4 hours at -55ºC (-67ºF)
4 hours at 25°C (77°F)
4 hours at 150°C (302°F)
4 hours at 25°C (77°F)
Print Legibility TE108-121012
Adhesion to aluminium plate TE 108-121030
Legible, 25N/25mm adhesion
Dry abrasion resistance
TE 109-121020
500 cycles, 500g, CS10 wheel
Legible, print contrast >3
180° Adhesion to:
Stainless steel
Aluminium
Acrylic painted surface
ABS
Nylon
PVC
TE 109-121030
If the document is printed it becomes uncontrolled
Check with TE Connectivity (TE) for latest version
15 N/25mm
20 N/25mm
20 N/25mm
20 N/25mm
15 N/25mm
15 N/25mm
Author: L Smith
Issue date: Aug 2014
Page:
2 of 3
While TE Connectivity Ltd. has made every reasonable effort to ensure the accuracy of the information in this document, TE does
not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is
accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any
time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not
limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are for
reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE
for the latest dimensions and design specifications.
TECHNICAL DATA SHEET
RayMark Six Labels
Document number: TTDS-032
Issue: 2
Date: August 2014
MARK PERMANENCE:
Fluid
Test Method
Required
MIL STD 202G Method 215
Solvent A
Solvent B
Solvent D
TE 109-121014
30 strokes, toothbrush
Legible, print contrast >3
Fluid Resistance
100°C, 2 hours:
Water
50°C, 24 hours:
Lubricating Oil
O-149
Salt water solution
(3.5% mass/mass)
23°C, 24 hours:
White Spirit
Iso Propyl Alcohol
Ethylene Glycol
Hydraulic Fluid
H-515
Diesel Fuel
23°C, 1 hour:
Skydrol 500B4
Mark permanence and 180° Peel test
to aluminium substraight
Immersion, followed by Print
Permanence, TE 109-121012, 20 rubs,
1kg load
Print legible,
minimum print contrast 3
10 N/25mm minimum
Immersion followed by 180° peel test,
TE 109-121030
Further information and availability can be found through the TE Cable Identification web site:
http://www.te.com/catalog/labels-identification/menu/en/12933?BML=10576
If the document is printed it becomes uncontrolled
Check with TE Connectivity (TE) for latest version
Author: L Smith
Issue date: Aug 2014
Page:
3 of 3
While TE Connectivity Ltd. has made every reasonable effort to ensure the accuracy of the information in this document, TE does
not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is
accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any
time without notice. TE expressly disclaims all implied warranties regarding the information contained herein, including, but not
limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are for
reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE
for the latest dimensions and design specifications.