STXR40AB45-1412BI

TINEL LOCK RING 3 CODE 40 - TINEL-LOCK BACKSHELL STXR40AB00-1616AI-S SERIES STXR: RING INCLUDED (SEE RING OPTION) STX: RING NOT INCLUDED CONNECTOR INTERFACE MATERIAL REFER TO CH00-0250-008 FINISH REFER TO CH00-0250-008 ANGLE ORDER NUMBER (TABLE 1) ENTRY SIZE (TABLE 2) RING OPTION AI - TO SUIT SINGLE BRAID BI - TO SUIT DOUBLE BRAID FOR STX, LEAVE BLANK MODIFICATION CODE REFER TO CH00-0250-008 2 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A BRAIDED CABLE SHIELD AND A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-008. 3. SEE DRAWING TR FOR DETAIL ON TINEL-LOCK RING, RINGS ARE DESIGNED TO BE HEATED ELECTRICALLY, ALL RINGS ARE MARKED WITH THERMOCHROMIC PAINT WHICH CHANGES COLOUR WHEN INSTALLATION TEMPERATURE IS REACHED. 4. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER LESS RING DESIGNATOR. (e.g. 06090-STXR40AB00-2018). RING SHALL BEAR NO MARKING. 5. TINEL-LOCK RING ENTRY SIZE AND BRAID DESIGNATOR IS TO BE SPECIFIED IN PART NUMBER WHEN ORDERING. 6. BACKSHELL MATES TO MIL-DTL-38999, SERIES III AND IV, CLASS C, F, K, AND W, D38999/20, /24, /26, /40, /46 AND /47 CONNECTORS, AND WHEN SO MATED SHALL PROVIDE A WATER-TIGHT SEAL MEETING THE REQUIREMENTS OF MIL-C-85049, PARA. 3. 5. 7. 7. PREFIX ' S' DENOTES THAT THE ADAPTER HAS A LARGER ENTRY THAN THE STANDARD TXR BUT IS STILL OF THE TYPE 1 DESIGN. 8. SEE SHEET 3 FOR TABLE OF ENTRY SIZE APPLICABLE TO THE STXR RANGE. FOR ENTRY SIZE LARGER THAN MAX INDICATED, CONTACT TE. MAX ENTRY ONLY APPLIES TO ANGLES 45 & 90. 9. THESE DIMENSIONS APPLY IF A SELF-LOCKING COUPLING NUT IS USED. DATE DRAWN K.WINCZURA 20/01/2015 CHECKED 20/01/2015 APPROVED K.SHEPPARD 29/01/2015 APPROVED H.SMITH 10/08/2015 REVISIONS LTR DESCRIPTION D REVISED PER ECO-15-002339 E REVISED PER ECO-15-010970 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 18/02/2015 10/08/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED H.SMITH H.SMITH If this document is printed it becomes uncontrolled. Check for the latest revision TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-38999 SERIES III & IV TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT STXR40 E 1 26,50 C SILICONE O-RING ØY ØS ØZ XXXX ØB A THREAD D PART MARK HERE 45° BACKSHELL STRAIGHT BACKSHELL W W T E E T 90° BACKSHELL STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE 90° BACKSHELL MODIFICATION S A THREAD ØB 9 SELF-LOCKING MECHANISM If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 20/01/2015 CHECKED 20/01/2015 APPROVED K.SHEPPARD 29/01/2015 APPROVED H.SMITH 10/08/2015 REVISIONS LTR DESCRIPTION D REVISED PER ECO-15-002339 E REVISED PER ECO-15-010970 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 18/02/2015 10/08/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED H.SMITH H.SMITH TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-38999 SERIES III & IV TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT STXR40 E 2 TABLE 1 ORDER SHELL SIZE A THREAD NUMBER COM / MIL 08 9/A M12 × 1.0 10 M15 × 1.0 11 / B 12 13 / C M18 × 1.0 M22 × 1.0 14 15 / D 16 17 / E M25 × 1.0 18 19 / F M28 × 1.0 20 21 / G M31 × 1.0 22 23 / H M34 × 1.0 24 25 / J M37 × 1.0 THESE DIMENSIONS APPLY IF BACKSHELL IS STAINLESS STEEL OR NICKEL ALUMINIUM BRONZE ØB MAX 18,0 21,0 24,5 29,0 32,5 35,5 37,0 40,0 43,5 ØB 9 MAX 21,5 24,6 28,3 32,4 35,6 38,5 41,7 43,9 47,0 ENTRY SIZE MIN MAX 8 05 06 08 10 10 12 12 16 14 18 16 20 18 22 20 24 22 24 TABLE 2 ENTRY SIZE 05 06 07 08 10 12 14 16 18 20 22 24 C ±0,5 12,0 12,5 13,1 13,5 14,5 15,5 16,1 16,5 17,0 ØZ MIN 7,92 9,53 11,10 12,70 15,88 19,05 22,23 25,40 28,58 31,75 34,93 38,10 D ±0,5 26,8 27,5 28,0 29,0 29,7 30,5 30,9 31,1 32,1 ØS 11,06 +/-0,04 12,66 +/-0,04 14,21 +/-0,07 15,81 +/-0,07 18,96 +/-0,08 22,14 +/-0,08 25,30 +/-0,08 28,48 +/-0,08 31,65 +/-0,08 34,83 +/-0,08 37,98 +/-0,08 41,15 +/-0,08 W ±0,5 21,0 24,0 27,0 31,0 34,0 35,0 38,0 42,0 45,0 T ±0,5 14,0 15,5 17,0 19,5 21,0 20,0 21,5 24,0 25,5 E ±0,5 26,20 27,95 29,45 31,00 32,70 34,25 35,80 37,40 38,90 W ±0,5 21,2 24,3 28,3 31,1 34,2 38,5 40,7 43,7 46,4 T ±0,5 16,3 17,2 19,4 21,0 22,8 25,3 26,1 27,6 29,1 E ±0,5 26,4 28,2 29,7 31,2 32,9 34,5 36,1 37,6 39,1 ØY ±03 15,50 17,10 18,70 20,30 23,50 26,70 29,80 33,00 36,20 39,40 42,50 45,70 If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 20/01/2015 CHECKED 20/01/2015 APPROVED K.SHEPPARD 29/01/2015 APPROVED H.SMITH 10/08/2015 REVISIONS LTR DESCRIPTION D REVISED PER ECO-15-002339 E REVISED PER ECO-15-010970 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 18/02/2015 10/08/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 APPROVED H.SMITH H.SMITH TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-38999 SERIES III & IV TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT STXR40 E 3