TX21AB90-1614

ANTI-ROTATIONAL SET SCREW 7 TINEL LOCK RING 3 CODE 21 - TINEL-LOCK BACKSHELL TXR21AB00-1608AISERIES TXR: RING INCLUDED (SEE RING OPTION) TX: RING NOT INCLUDED CONNECTOR INTERFACE MATERIAL REFER TO CH00-0250-008 FINISH REFER TO CH00-0250-008 ANGLE DASH NUMBER (TABLE 1) ENTRY SIZE (TABLE 2) RING OPTION AI - TO SUIT SINGLE BRAID BI - TO SUIT DOUBLE BRAID FOR TX, LEAVE BLANK MODIFICATION CODE REFER TO CH00-0250-008 2 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A BRAIDED CABLE SHIELD AND A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-008. 3. SEE DRAWING TR FOR DETAIL ON TINEL-LOCK RING, RINGS ARE DESIGNED TO BE HEATED ELECTRICALLY, ALL RINGS ARE MARKED WITH THERMOCHROMIC PAINT WHICH CHANGES COLOUR WHEN INSTALLATION TEMPERATURE IS REACHED. 4. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER LESS RING DESIGNATOR. (e.g. 06090-TXR21AB00-1406). RING SHALL BEAR NO MARKING. 5. FOR LARGER ENTRY SIZES, A 2 PIECE BACKSHELL ASSEMBLY (TYPE 2) IS SUPPLIED. 6. BACKSHELL MATES TO MIL-DTL-26482 SERIES I, MS3110, MS3116, MS3120, MS3126 CLASS E AND F CONNECTORS. 7. ANTI-ROTATIONAL SET SCREW, 3 THREADED HOLES 120° ± 5° APART, SINGLE MATING SET SCREW SUPPLIED. If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 04/12/2014 CHECKED 04/12/2014 APPROVED K.SHEPPARD 08/12/2014 APPROVED H.SMITH 13/07/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECO-15-002324 J REVISED PER ECO-15-010170 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE APPROVED 17/02/2015 H.SMITH 13/07/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 H.SMITH TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-26482 SERIES I TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT TXR21 J 1 IF MAX ENTRY IS EXCEEDED BACKSHELL WILL BE SUPPLIED AS TYPE 2 21,50 `0,50 30,40 26,50 XXXX A THREAD ØB ØK ØY ØS ØZ XXXX ØB A THREAD SILICONE O-RING 5 PART MARK HERE PART MARK HERE STRAIGHT BACKSHELL - TYPE 2 STRAIGHT BACKSHELL - TYPE 1 F C 21,50 ` 0,50 D G 45° BACKSHELL - TYPE 2 45° BACKSHELL - TYPE 1 W H 21,50 `0,50 T J E M 90° BACKSHELL - TYPE 1 90° BACKSHELL - TYPE 2 H W 21,50 T J E M 90° BACKSHELL - TYPE 1 STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 04/12/2014 CHECKED 04/12/2014 APPROVED K.SHEPPARD 08/12/2014 APPROVED H.SMITH 13/07/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECO-15-002324 J REVISED PER ECO-15-010170 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE APPROVED 17/02/2015 H.SMITH 13/07/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 H.SMITH 90° BACKSHELL - TYPE 2 STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-26482 SERIES I TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT TXR21 J 2 TABLE 1 ORDER NUMBER 08 10 12 14 16 18 20 22 24 TABLE 2 ENTRY SIZE 04 05 06 07 08 10 12 14 16 18 20 22 24 THESE DIMENSIONS APPLY IF BACKSHELL IS STAINLESS STEEL OR NICKEL ALUMINIUM BRONZE SHELL SIZE 08 10 12 14 16 18 20 22 24 A THREAD 7/16-28UNEF 9/16-24UNEF 11/16-24UNEF 13/16-20UNEF 15/16-20UNEF 1 1/16-18UNEF 1 3/16-18UNEF 1 5/16-18UNEF 1 7/16-18UNEF ØB MAX 18,05 21,55 24,65 27,65 31,05 34,35 37,55 40,55 43,55 C ±0,5 13,9 14,7 15,1 16,0 16,3 17,3 18,1 18,5 19,3 MAX ENTRY 04 06 08 10 12 12 14 16 18 D ±0,5 26,8 27,5 28,0 29,0 29,7 30,5 30,9 31,1 32,1 W ±0,5 25,0 28,0 31,5 35,0 38,0 41,5 45,0 48,0 51,0 T ±0,5 17,5 18,6 20,5 22,5 24,0 26,0 28,0 29,5 31,0 E ±0,5 26,20 27,95 29,45 31,00 32,70 34,25 35,80 37,40 38,90 W ±0,5 22,5 25,8 29,5 32,7 35,5 39,3 42,7 45,7 48,4 T ±0,5 17,5 18,6 20,5 22,5 24,0 26,0 28,0 29,5 31,0 E ±0,5 26,4 28,2 29,7 31,2 32,9 34,5 36,1 37,6 39,1 THESE DIMENSIONS APPLY IF BACKSHELL IS STAINLESS STEEL OR NICKEL ALUMINIUM BRONZE ØZ MIN 6,35 7,92 9,53 11,10 12,70 15,88 19,05 22,23 25,40 28,58 31,75 34,93 38,10 ØS 9,49 +/-0,04 11,06 +/-0,04 12,66 +/-0,04 14,21 +/-0,07 15,81 +/-0,07 18,96 +/-0,08 22,14 +/-0,08 25,30 +/-0,08 28,48 +/-0,08 31,65 +/-0,08 34,83 +/-0,08 37,98 +/-0,08 41,15 +/-0,08 ØY ± 0,3 14,00 15,50 17,10 18,70 20,30 23,50 26,70 29,80 33,00 36,20 39,40 42,50 45,70 F ±0,5 NA 12,5 12,5 12,5 13,1 13,5 14,5 15,5 16,1 16,5 17,0 18,5 21,9 ØK MAX NA 21,0 21,0 21,0 24,5 29,0 32,5 35,5 37,0 40,0 43,5 48,5 52,1 G ±0,5 NA 27,5 27,5 27,5 28,0 29,0 29,7 30,5 30,9 31,1 32,1 35,3 38,1 H ±0,5 NA 24,0 24,0 24,0 27,0 31,0 34,0 35,0 38,0 42,0 45,0 54,5 58,0 M ±0,5 NA 15,5 15,5 15,5 17,0 19,5 21,0 20,0 21,5 24,0 25,5 31,0 33,0 J ±0,5 NA 27,95 27,95 27,95 29,45 31,00 32,70 34,25 35,80 37,40 38,90 42,00 46,00 H ±0,5 NA 24,3 24,3 24,3 28,3 31,1 34,2 38,5 40,7 43,7 46,4 50,0 53,5 M ±0,5 NA 17,2 17,2 17,2 19,4 21,0 22,8 25,3 26,1 27,6 29,1 31,0 33,0 J ±0,5 NA 28,2 28,2 28,2 29,7 31,2 32,9 34,5 36,1 37,6 39,1 42,0 46,0 If this document is printed it becomes uncontrolled. Check for the latest revision DATE DRAWN K.WINCZURA 04/12/2014 CHECKED 04/12/2014 APPROVED K.SHEPPARD 08/12/2014 APPROVED H.SMITH 13/07/2015 REVISIONS LTR DESCRIPTION H REVISED PER ECO-15-002324 J REVISED PER ECO-15-010170 3RD ANGLE PROJECTION NOT TO SCALE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE APPROVED 17/02/2015 H.SMITH 13/07/2015 TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 H.SMITH TITLE: TINEL-LOCK BACKSHELL ASSY USED ON: MIL-DTL-26482 SERIES I TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT TXR21 J 3