U7139-030PA-5W0000

U7100 Pressure Transducer SPECIFICATIONS • Performance standard for on and off highway engine & vehicle OEMs • Rugged for heavy equipment and outdoor use such as HVAC refrigeration systems • Designed specifically for high volume applications • Stainless steel wetted surfaces • Low pressure ranges • CE Approved • UL Certified • Gage, absolute, sealed gage The U7100 pressure transducer from the UltraStable line of MEAS sets a new price performance standard for demanding engine and vehicle, and industrial applications. This transducer is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam and corrosive fluids. The transducer pressure cavity is constructed of 316L stainless steel and there are no internal O-rings or organics exposed to the pressure media. Having excellent durability, it is available with a variety of leak-proof, all metal pressure connections. The U7100 is an automotive grade pressure transducer with hermetic pressure ports and an integral electrical connector with standard pressure ranges from 0 to 15, up to 150psi (10Bar). This pressure sensor exceeds the latest industrial CE requirements and includes automotive electronics requirements such as surge protection, as well as being overvoltage protected to 16Vdc in both positive and reverse polarity. This product is geared to the OEM customer for low to mid volumes. MEAS stands ready to provide a custom design of the U5700 where the volume and application warrants. Additional configurations not listed are either available or possible. Please inquire for further information. SENSOR SOLUTIONS ///U7100 09/2017 Page 1 U7100 Pressure Transducer FEATURES • • • • • Hermetic Pressure Ports Integral Electrical Connector Survives High Vibration ±0.25% Accuracy Water Resistant 1M Immersion APPLICATIONS • • • • • On and Off Highway Engines and Vehicles HVAC Refrigeration Controls Compressors Hydraulics Energy and Water Management STANDARD RANGES Range (psi) Range (Bar) Gage 0 to 015 0 to 001 • 0 to 030 0 to 002 0 to 050 0 to 100 0 to 150 0 to 010 SENSOR SOLUTIONS ///U7100 Absolute Sealed Gage • • • 0 to 3.5 • • • 0 to 007 • • • • • • 09/2017 Page 2 U7100 Pressure Transducer PERFORMANCE SPECIFICATIONS Ambient Temperature: 25°C (unless otherwise specified) PARAMETERS MIN Load Resistance TYP MAX UNITS 10 NOTES kΩ Accuracy (combined linearity, hysteresis & repeatability) -0.25 0.25 %Span 1 Total Error Band -1.0 1.0 %Span 2 Compensated Temperature -20 +85 °C Operating Temperature -40 +125 °C Storage Temperature -40 +125 Insulation Resistance (500Vdc) 100 °C MΩ Short Circuit Protected Yes Output Noise @ 1kHZ 10 Response Time (10% to 90%) 4 mV 1.0 Long Term Stability 3 ms -0.25 0.25 %Span/Year Notes 1. Best fit straight line. 2. TEB includes all accuracy errors, thermal errors, span and zero tolerances over the compensated temperature range. 3. Temperature range for product with standard cable is -20°C to +105°C. 4. Between sensor body to any pins of connector. ENVIRONMENTAL SPECIFICATIONS Ambient Temperature: 25°C (unless otherwise specified) PARAMETERS MAX UNITS Humidity (@40°C) 93 %RH Pressure Overload 3X Rated 5 Pressure Burst 4X Rated 6 Pressure Cycle MIN TYP 10M Mechanical Vibration NOTES Cycles 20g, 10 ~ 2000Hz MIL-STD-810C, Method 514.2, Curve L Mechanical Shock Half-Sine, Peak: 50g, 11ms MIL-STD-202, Method 213B, Condition A Package Protection IP67 (IEC60529) Notes 5. The maximum pressure that can be applied without changing the transducer’s performance or accuracy. 6. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer. Agency Approvals RoHS: RoHS 2 (Directive 2011/65/EU) UL 508 Certified: Industrial Control Equipment, CSA 22.2 No. 14-10 EMC Performance Criteria: Output Change < ±1.5% FSO IEC61000-4-2 ESD: 8kV Contact / 15kV Air; Discharge Rate > 10s IEC61000-4-3 EM Field: 100V/m, 1kHz 80% Modulation, 80 ~ 1000MHz IEC61000-4-4 Electrical Fast Transient: Level 2, 1KV each line, Capacitance coupling IEC61000-4-5 Surge: Level 2, 42Ω Impedance, Figure 11 (L-L 500V, L-E 1KV) IEC61000-4-6 Conducted RF: Level 2, 3V/130dB, 150KHz ~ 80MHz, 2s Dwell, Clamp Injection IEC61000-4-9 Pulse Magnetic Field: Level 3, 100A/m, 10 Second pulse interval IEC55022 Emission: Class B, 30dB @ 30-230MHz, 37dB @ 230-1000MHz SENSOR SOLUTIONS ///U7100 09/2017 Page 3 U7100 Pressure Transducer Pressure Ports Pressure Port Options Dim A Tightening Torque (Nm) 2 = G1/4, BS5380, Male .43 [11.0] 30~35 4 = 7-16-20 UNF, SAE J1926-2, Male, w/ O-Ring .36 [9.1] 18~20 5 = 1/4-18 NPT Male .56 [14.2] 2~3 T.F.F.T. 6 = 1/8-27 NPT Male .38 [9.7] 2~3 T.F.F.T. E = R1/4-19, Male .56 [14.2] 2~3 T.F.F.T. F = G1/4-19, BS5380, Female .64 [16.3] 30~35 P = 7/16-20UNF Female w/ Integral Valve Depressor; 1/4 Flare Gasket SAE J513C, Copper .64 [16.3] 15~16 Q = M10 x 1.0, ISO 6149-2, Male .37 [9.5] 15~16 S = M12 x 1.5, ISO 6149-2, Male .43 [11.0] 28~30 G = M14 x 1.5, ISO 6149-2, Male .43 [11.0] 30~35 U = G1/4, DIN 3852-E, Male .47 [12.0] 30~35 Notes: Installation *T.F.F.T.: Turns From Finger Tight Transducers can be installed by either spanner or deep socket. Torque values provided are for reference: actual torque depends upon mating port material, surface finish, lubrication and sealing mechanism. Transducers calibration and/or zero may shift if part is over-torqued during installation. Check for a zero shift after installing. Connector Packard Metri-Pack 150 Series Sumitomo HV040 Series AMP Econoseal-J Mark II 070 Series Connector, Pin Plating Connector, Mating powerandsignal.com 0.003 – 0.005 mm Sn sumitomokenki.com 0.003 mm Sn over 0.0005 – 0.001 mm Cu 0.0004 mm Au over 0.0013 mm Ni te.com Housing P/N: 12065287 Terminals P/N: 12103881 Housing P/N: 6189-6907 Terminals P/N: 8100-3067/8 Housing P/N: 174357 Terminals P/N: 171630 Notes: Connector Do not apply torque to the connector housing of transducer. To ensure proper environmental sealing and electrical connection when using a mating connector, follow the manufacturer’s installation guidelines. SENSOR SOLUTIONS ///U7100 09/2017 Page 4 U7100 Pressure Transducer DIMENSIONS SENSOR SOLUTIONS ///U7100 09/2017 Page 5 U7100 Pressure Transducer CHARTS Pressure Transfer Function Supply = 5V OEM Custom Calibration High/Low Rail values can be adjusted by circuit Output Type Vs. Supply Output Type (Code) 3 Supply Voltage 4.75 ~ 5.25V* Supply Current 4.0 ~ 10.0mA Output Voltage 0.5 ~ 4.5V* Reverse Voltage 16V Overvoltage Protection 16V * Output Ratiometric to Supply Voltage SENSOR SOLUTIONS ///U7100 09/2017 Page 6 U7100 Pressure Transducer ORDERING INFORMATION U71 3 1 – 100P A - P W 0000 Output Code 3 Port Material W 316L Stainless Steel Type 0.5 – 4.5V Cable/Connector Code Connection Type 1 Cable, 2 feet LG 2 Cable, 4 feet LG 3 Cable, 10 feet LG 7 AMP070 connector 8 Sumitomo HV040 Connector 9 Packard Connector M Cable, 1 meter LG N Cable, 2 meter LG P Cable, 5 meter LG R Cable, 10 meter LG Pressure Port Type Code Port 2 G1/4, BS5380, Male 7/16-20 UNF Male SAE 4 J1926-2, Male, w/ O-ring 5 1/4-18 NPT Male 6 1/8-27 NPT Male E R1/4-19, Male F G1/4-19, BS5380, Female 7/16-20 UNF Female w/ Integral Valve Depressor: 1/4 P Flare Gasket SAE J513C, Copper Q M10x1.0, ISO 6149-2, Male S M12x1.5, ISO 6149-2, Male G M14x1.5, ISO 6149-2, Male U G1/4, DIN 3852-E, Male Pressure Range psi bar 015P* 001B* 030P 002B 050P 3.5B 100P 007B 150P 010B *Gage Only Dim “A” .43[11.0] .43[11.0] .56[14.2] .38[9.7] .56[14.2] .64[16.3] .64[16.3] .37[9.5] .43[11.0] .43[11.0] .47[12.0] Pressure Type A Absolute S Sealed Gauge G Gage NORTH AMERICA EUROPE ASIA Measurement Specialties, Inc., a TE Connectivity Company Phone: 800-522-6752 Email: customercare.frmt@te.com Measurement Specialties (Europe), Ltd., a TE Connectivity Company Phone: +31 73 624 6999 Email: customercare.lcsb@te.com Measurement Specialties (China), Ltd., a TE Connectivity Company Phone: 0400-820-6015 Email: customercare.shzn@te.com TE.com/sensorsolutions Measurement Specialties, Inc., a TE Connectivity company. Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2015 TE Connectivity Ltd. family of companies SENSOR SOLUTIONS ///U7100 All Rights Reserved. 09/2017 Page 7