U86B-010BS

U86B Urea Dosing SPECIFICATIONS FEATURES • • • • • Mountable O-ring with seal ±0.5% Accuracy ±2.0 Total Error Band Cable option Freeze Protection Available APPLICATIONS • • • • • Urea level Urea pressure Air brakes Corrosive fluid measurement for E&V applications Automotive SENSOR SOLUTIONS ///U86B • Mountable with O-ring seal • Stainless Steel wetted surfaces • Amplified • ASIC calibrated • Absolute, sealed gage • Cable option • Analog output • SENT Output Optional (contact factory for details) The U86B is an automotive designed 16mm media isolated, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing and is designed for O-ring mounting. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. The U86B is designed for high performance, low pressure applications. A custom ASIC is used for temperature compensation, offset correction, and provides an amplified output of 0.5 to 4.5V. CE approved and manufactured to TS16949 standard, this model may also come with a cable if desired. For a similar sensor without plastic housing, refer to the 86A or for a plastic threaded fitting, refer to the LM pressure transducer. 07/2018 Page 1 U86B Urea Dosing STANDARD RANGES Range psiA, psiG, psiS Range barA, barG, barS 0 to 050 • 0 to 005 • 0 to 100 • 0 to 010 • 0 to 150 • 0 to 012 • 0 to 200 • 0 to 013 • Other pressure ranges available, please contact factory PERFORMANCE SPECIFICATIONS Unless otherwise specified: Supply Voltage: 5V, Ambient Temperature: 25°C after 10 sec warm-up PARAMETERS MIN TYP MAX Supply Voltage 4.75 5.00 5.25 V 12.5 mA DC Supply Current UNITS NOTES Ratiometric Output 0.5 4.5 V 1, 5 Accuracy (combined linearity, hysteresis & repeatability) -0.5 0.5 %Span 2 Total Error Band -2.0 2.0 %Span 3 Compensated Temperature -7 +105 °C Operating Temperature -40 +105 °C Storage Temperature -40 +125 Insulation Resistance (500VDC) 10 °C MΩ Reverse Voltage Overvoltage Protection 18 V 18 V Continuous Short Circuit Protection Output Noise @ 1kHZ 13 mV Response Time (10% to 90%) 1.0 ms Long Term Stability Output Load 4 -0.15 0.15 47 Diagnostics Ability %Span/Year kΩ Included Notes 1. 2. 3. 4. 5. Ratiometric to supply voltage, pressure transfer function at 5V Voltage Supply, see Chart A Best Fit Straight Line TEB includes all accuracy errors, thermal errors, span and zero tolerance over the compensated range Between sensor body to any pins of connector This product can be configured for custom OEM requirements, contact factory for different transfer functions and output clipping. See Chart B SENSOR SOLUTIONS ///U86B 07/2018 Page 2 U86B Urea Dosing ENVIRONMENTAL SPECIFICATIONS PARAMETERS MAX UNITS NOTES Pressure Overload MIN 2X Rated 6 Pressure Burst 3X Rated 7 Pressure Cycle TYP 1M Cycles Port: 316/316L ST STL Sealing: FKM Fluoroelastomer 70 (O-Ring) Housing: PA66 + 30%GF Material Freezing Protecting Optional 9 Notes 6. 7. 8. 9. The maximum pressure that can be applied without changing the transducer’s performance or accuracy. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer. Transducers can be installed by M4X0.7 Torx washer head screws (qty 2) with 2.2Nm torque (values provided are for reference). Actual torque depends upon on mating support material, surface flatness and different screws. Transducer housing may crack if over-torqued when installing Medium dead volume that exceeds 350mm3 max in manifold (excluding sensor) may damage the sensor during frozen condition Agency Approvals EMC Performance Criteria: Output Change < ±1.5% of FS @RT ESD 8kV Contact / 15kV Air ISO 10605 Immunity Radiated Field Level V, 140V/m, 200MHz-3.2GHz ISO 11452-2 BCI d = 150mm, d = 450mm, d = 750mm ISO 11452-4 Frequency Range: 1MHz-400MHz Modulation CW, AM Severity Level V (200mA) SENT Only Magnetic Field Test ISO 11452-8 Emission Conducted. Voltage Mode/Current Probe CISPR 25 Emission Radiated CISPR 25 Output Interface SENSOR SOLUTIONS ///U86B 15Hz to 150kHz, Level 4 Frequency Range: 150kHz – 108MHz, Class 5 Frequency Range: 150kHz - 2.5GHz, Class 5 SENT (SAE J2716, 2010) 07/2018 Page 3 U86B Urea Dosing CHARTS Chart A: Pressure Transfer Function, Supply = 5V 𝑂𝑢𝑡𝑝𝑢𝑡 𝑉𝑜𝑙𝑡𝑎𝑔𝑒 = 80% × 𝑆𝑢𝑝𝑝𝑙𝑦 𝑉 × (𝑃𝑟𝑒𝑠𝑠𝑢𝑟𝑒 𝐴𝑝𝑝𝑙𝑖𝑒𝑑 − 𝑃𝑚𝑖𝑛) + 10% × 𝑆𝑢𝑝𝑝𝑙𝑦 𝑉 𝑃𝑚𝑎𝑥 − 𝑃𝑚𝑖𝑛 Chart B: OEM Custom Calibration. High/Low Rail values can be adjusted by Circuit SENT Functional Block Diagram (Pin 1) (Pin 3) (Pin 2) SENSOR SOLUTIONS ///U86B 07/2018 Page 4 U86B Urea Dosing DIMENSIONS Dimensions are in inches [mm] Non-Vent Cap/Non-Freeze option shown See Note 8 See Note 9 SENSOR SOLUTIONS ///U86B 07/2018 Page 5 U86B Urea Dosing CABLE DIMENSIONS See “Cable Ordering Information” matrix for cable length options MOLEX HOUSING # 50-57-9403 MOLEX TERMINALS # 16-02-0082 (.100 [2.54] PITCH) HIGH TEMPERATURE CABLE, 3 CONDUCTORS, 24 AWG MOLEX CONNECTOR # 43645-0300 MOLEX TERMINALS # 43030-0003 CONDUCTOR: 24 AWG RATED VOLTAGE: 300V TEMPERATURE RANGE: -40OC – 200OC Customer & Sensor Side Pos No Color Function 1 Red Supply 2 Black GND 3 Blue Output SENSOR SOLUTIONS ///U86B 07/2018 Page 6 U86B Urea Dosing ORDERING INFORMATION U86B – 100P A 2 – F 1 A Output Type A Analog Pressure Range 050P 005B 100P 010B 150P 012B 200P 013B Pressure Type G Gage A Absolute S Sealed Gage 1 2 3 1 Connector Molex Freeze Protection N None F Freeze Output Ratiometric 0.5V @ 0.0barG/A/S 0.5V @-0.5barG/S 0.5V @ -1.0 barG/S SENT Output available, contact factory for details CABLE ORDERING INFORMATION U86B – CBL – 010 – 1 005 010 020 Cable Length 5 [127] 10 [254] 20 [508] 0 1 Connector No Connector Molex Connector #50579403 Cable Lengths are in inches[mm] NORTH AMERICA EUROPE ASIA Measurement Specialties, Inc., a TE Connectivity Company Tel: +1 800-522-6752 Email: customercare.frmt@te.com Measurement Specialties (Europe), Ltd., a TE Connectivity Company Tel: +31 73 624 6999 Email: customercare.lcsb@te.com Measurement Specialties (China), Ltd., a TE Connectivity Company Tel: +86 0400-820-6015 Email: customercare.shzn@te.com TE.com/sensorsolutions Measurement Specialties, Inc., a TE Connectivity company. Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. © 2015 TE Connectivity Ltd. family of companies SENSOR SOLUTIONS ///U86B All Rights Reserved. 07/2018 Page 7