V23086R1802A803

Automotive Relays PCB Single Relays Micro Relay K (THT – THR) ■ Small power relay ■ Limiting continuous current 20A at 85°C ■ Low weight ■ Low noise operation ■ Wave (THT) and reflow (THR/pin-in-paste) solderable versions ■ For double version refer to Double Micro Relay K Typical applications Door lock, heated front/rear screen, lamps front/rear/fog light, interior lights, seat control, sun roof, window lifter, wiper control. 086C/R1_fcw1b Contact Data Typical applications Inductive load Wiper load Resistive/inductive load Lamp load V23086-*1*01-A403 V23086-*1*02-A803 V23086-*1*01-A402 V23086-*1*51-A502 Contact arrangement 1 form C, 1 CO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO Rated voltage 12VDC 10VDC 12VDC 10VDC NO/NC NO/NC Rated current1) 30/25A 30/25A 30A 15A Limiting continuous current1) 23°C 30/25A 30/25A 30A 15A 85°C 20/15A 20/15A 20A 10A 105°C 15/10A 15/10A 15A 2) 2) 2) Limiting making current 40A 40A 40A 100A3) Limiting breaking current 30A 30A 30A 30A Contact material AgSnO2 Min. contact load >1A at 5VDC4) Initial voltage drop at 10A, typ./max. 30/300mV Operate/release time typ. 3/1.5ms5) Electrical enduranc cyclic temperature -40°C, +25°C, +85°C form C contact (CO) at 14VDC motor reverse blocked, wiper, 25A, 0.77mH 25A make/5A break, >1x105 ops. generator peak, 20A on NC,1mH >1x106 ops. form A contact (NO) at 14VDC resistive 20A lamp 100A inrush, >1x105 ops. 10A steady state >1x105 ops. Mechanical endurance >5x106 ops. Max. DC load breaking capacity 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 25cm2 (double layer 105μm) copper area. Connecting cable cross section 6 mm2.Boundary conditions: 180°C coil temperature;130°C solder joint. 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) Corresponds to the peak inrush current on initial actuation (cold filament). 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 5) Measured at nominal voltage without coil suppression unit. A low resistive suppression device in parallel to the relay coil increases the release time and reducesthe lifetime caused by increased erosion and/or higher risk of contact tack welding. 100 Max. Switching Voltage in VDC 0W 1 42 0.1 0W 0W W 10 20 10 30 curve I curve II 10 Switching Current in A 100 Load limit curve 1: arc extinguishes, during transit time (changeover contact). Load limit curve 2: safe shutdown, no stationary arc (make contact). Load limit curves measured with low inductive resistors verified for 1000 switching events. 07-2017, Rev. 0717 www.te.com © 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 1 Automotive Relays PCB Single Relays Micro Coil Data Rated coil voltage Relay K (THT – THR) (Continued) Other Data 12VDC Coil versions, DC coil Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC Ω±10% mW 001/801 12 6.9 1.5 254 0567 002/802 10 5.7 1.25 181 0552 051/851 10 6.5 1.1 90 1111 All figures are given for coil without pre-energization, at ambient temperature +23°C. Coil operating range 300 250 Umax 200 150 100 50 Uop (E=0V) 0 -40 -20 0 20 40 60 Ambient temperature in °C 80 100 120 Does not take into account the temperature rise due to the contact current E = pre-energization Insulation Data Initial dielectric strength between open contacts between contact and coil 500VACrms 500VACrms EU RoHS/ELV compliance compliant Ambient temperature, DC coil -40 to +105°C Cold storage, IEC 60068-2-1 1000h; -40°C Dry heat, IEC 60068-2-2 1000h; +125°C Climatic cycling with condensation, EN ISO 6988 20 cycles, storage 8/16h Temperature cycling (shock), IEC 60068-2-14, Na 100 cycles; -40/+125°C Temperature cycling, IEC 60068-2-14, Nb 35 cycles; -40/+125°C Damp heat cyclic, IEC 60068-2-30, Db, variant 1 6 cycles 25°C/55°C/93%RH Damp heat constant, IEC 60068-2-3 method Ca 56 days 40°C/95%RH Degree of protection THT: RT III (61810) THR: RT II (61810) Sealing test, IEC 60068-2-17: THT Qc, method 2, 1min, 70°C Corrosive gas IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional) IEC 60068-2-6 (sine sweep) 10 to 500Hz; 6g6) Shock resistance (functional) IEC 60068-2-27 (half sine) 6ms, up to 30g6) Terminal type PCB:THT, THR Weight approx. 4g (0.14oz) Solderability (aging 3: 4h/155°C) THT IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C Solderability THR IEC60068-2-58 hot dip 5s 245°C Resistance to soldering heat THT IEC 60068-2-20 Tb, method 1A, hot dip 10s, 260°C with thermal screen Resistance to soldering heat THR IEC 60068-2-58 260°C; preheating min 130°C Storage conditions according IEC 60068-17) Packaging unit 2000 pcs. 6) Depending on mounting position: no change in the switching state >10μs. 7) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ 2 07-2017, Rev. 0717 www.te.com © 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Mounting Hole Layout Bottom view on solder pins Terminal Assignment Bottom view on solder pins 1 form A, 1 NO 1 form C, 1 CO 1 C 2 7.5 0.5 B 1.72 4 5 0.5 10.2 1 Dimensions Micro Relay K, THT version 2 5x 5.8 A B A 0.4 0.3 ± 0.1 A C A TE86etw_an1 7.65 0.4 ± 0.2 Remark: Positional tolerances according to DIN EN ISO 5458 9.9 ± 0.2 ± 0.1 0.6 ± 0.1 ± 0.2 5x 0.4 0.3 12.0 ± 0.2 2.5 3.6 +0.05 0 3 3.0 2x 1.38 86etw_ab 86ets_ab 3x 2 8.5 +0 .0 5 5 0 1 5 4 3 1. 2 4 12.9 0.95 ± 0.3 2.8 ± 0.2 *) A ± 0.2 TE86etw_se *) Additional tin tops max. 1 mm *) Additional tin tops max. 1mm 07-2017, Rev. 0717 www.te.com © 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 3 Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Mounting Hole Layout Bottom view on solder pins *) Micro Relay K, THR version 86R1_DD2_2 86R1_VT3 View of Stand-Offs Bottom view on solder pins 86R1_DD1_2 86R1_VT1 *) Additional tin tops max. 1mm 4 07-2017, Rev. 0717 www.te.com © 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. Automotive Relays PCB Single Relays Micro Relay K (THT – THR) (Continued) Product code structure Typical product code V23086 -C 1 001 -A 4 03 Type V23086 Micro Relay K (THT – THR) Terminal and enclosure C PCB version THT, sealed Design 1 Single relay Coil 001 Standard (THT) 801 Standard (THR) 051 Lamp load (THT) Contact type A Single contact Contact material index 4 AgSnO2 standard 5 AgSnO2 lamp load Contact arrangement index 02 NO Product code V23086-C1001-A402 V23086-C1001-A403 V23086-C1051-A502 V23086-C1002-A803 V23086-R1801-A402 V23086-R1801-A403 V23086-R1851-A502 V23086-R1802-A803 Version PCB THT, cleanable PCB THR, vented R PCB version THR, vented 002 802 851 Sensitive (THT) Sensitive (THR) Lamp load (THR) 8 AgSnO2 wiper load 03 CO Design Single Coil Standard Contact Single Cont. material AgSnO2 (standard) Lamp load Sensitive Standard AgSnO2 (lamp) AgSnO2 (wiper) AgSnO2 (standard) Lamp load Sensitive AgSnO2 (lamp) AgSnO2 (wiper) Arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form C, 1 CO Part number 0-1393280-5 0-1393280-6 2-1904093-1 2-1414987-3 2-1904093-2 6-1414920-0 9-1904064-4 7-1414967-8 This list represents the most common types and does not show all variants covered by this datasheet. Other types on request. 07-2017, Rev. 0717 www.te.com © 2017 TE Connectivity. Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ section, application notes and all specifications are subject to change. 5