X2-18.0-0-SP-SM

 r and  UL  Temperature rating °C 90°C –30°C to 125°C Specifications* ® ® Type Raychem UL CSA * When ordering, always specify latest issue. Dimensions (millimeters) Size 1.0 1.5 2.0 2.5 3.0 3.5 4.0 5.0 6.0 7.0 As supplied D Inside diameter 1.5 ± 0.2 2.1 ± 0.2 2.6 ± 0.2 3.1 ± 0.2 3.6 ± 0.2 4.1 ± 0.3 4.6 ± 0.3 5.6 ± 0.3 6.6 ± 0.3 7.6 ± 0.3 W1 Wall thickness (nominal) 0.2 0.2 0.25 0.25 0.25 0.25 0.25 0.3 0.3 0.3 Part as supplied Fully recovered d (max.) W2 (min.) Inside Wall diameter thickness** 0.5 0.44 0.75 0.44 1.0 0.44 1.25 0.44 1.5 0.44 1.75 0.46 2.0 0.46 2.5 0.56 3.0 0.56 3.5 0.56 Part fully recovered Size 8.0 9.0 10.0 11.0 12.0 16.0 18.0 20.0 25.0 30.0 **Wall thickness will be less if tubing recovery is restricted during shrinkage. Ordering information Color S S M Standard A s s spools Marked (standard types). UL, CSA, and Japan -F- Mark on labels. and As supplied D Inside diameter 8.6 ± 0.3 9.6 ± 0.3 10.4 ± 0.3 11.4 ± 0.3 12.7 ± 0.3 16.9 ± 0.4 19.0 ± 0.4 21.5 ± 0.5 27.0 ± 0.6 32.4 ± 0.8 W1 Wall thickness (nominal) 0.3 0.3 0.3 0.3 0.3 0.35 0.4 0.4 0.45 0.45 Fully recovered d (max.) W2 (min.) Inside Wall diameter thickness** 4.0 0.56 4.5 0.56 5.0 0.56 5.5 0.56 6.0 0.56 8.0 0.69 9.0 0.77 10.0 0.77 12.5 0.77 15.0 0.89 Specification values Property Dimensions Longitudinal change ASTM D 2671 UL 224 Eccentricity (recovered) Tensile strength Ultimate elongation Secant modulus (as supplied) Low-temperature flexibility (1 hour at –30°C/–22°F) Heat shock (4 hours at 250°C/482°F) Heat aging (7 days at 158°C/316°F) Followed by tests for: Tensile strength Physical Electrical Chemical Requirement See reverse Method of test ASTM D 2671 percent percent percent MPa (psi) percent MPa (psi) +1, –5 +3, –3 30 maximum 10.3 (1500) minimum 200 minimum 172 (2.5 x 104) maximum No cracking ASTM D 2671 UL 224 ASTM D 2671 ASTM D 2671 ASTM D 2671 ASTM D 2671 UL 224 No cracking UL 224 UL 224 MPa (psi) Ultimate elongation Flexibility Dielectric withstand at 2500 V Dielectric breakdown percent Dielectric strength Restricted shrinkage Dielectric withstand at 2500 V Dielectric strength Volume resistivity Corrosive effect (7 days at 158°C/316°F) Copper stability (7 days at 158°C/316°F) kV/mm (volts/mil) Followed by test for: Ultimate elongation Flammability Note: Consult Unit mm seconds volts seconds kV/mm (volts/mil) ohm-cm percent 70% minimum of unaged specimens 100 minimum No cracking 60 minimum UL 224 UL 224 UL 224 ASTM D 2671 50% minimum of unaged specimens 19.7 (500) minimum Pass 60 minimum ASTM D 2671 ASTM D 2671 UL 224 ASTM D 2671 19.7 (500) minimum 1014 minimum No corrosion ASTM D 2671 ASTM D 2671 ASTM D 2671 No brittleness, glazing, cracking, or severe discoloration of tubing. No pitting or blackening of copper. ASTM D 2671 100 minimum Pass ASTM D 2671 UL 224, VW-1 for specific details about test procedures. Users should independently evaluate the suitability of the product for their application. te.com © 2019 TE Connectivity Ltd. family of companies. All Rights Reserved. APL 3/2019 TE Connectivity, TE, TE connectivity (logo) and RAYCHEM are trademarks of the TE Connectivity Ltd. family of companies. Other logos, product and/or company names might be trademarks of their respective owners. While TE has made every reasonable effort to ensure the accuracy of the information in this document, TE does not guarantee that it is error-free, nor does TE make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE reserves the right to make any adjustments to the information contained herein at any time without notice. TE EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES REGARDING THE INFORMATION CONTAINED HEREIN, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. In ne event will TE be liable for any direct, indirect, incidental, special or consequential damages arising from or related to recipient’s use of the information. It is the sole responsibility of the recipient of this information to verify the results of this information using their engineering and product environment. Recipient assumes any and all risks associated with the use of the information. The dimensions in this catalog are for reference purposes only and are subject to change without notice. All specifications are subject to change without notice. Consult TE for the latest dimensions and design specifications.