HMP151P7EFR8C-S6

240pin Registered DDR2 SDRAM DIMMs based on 1Gb version E This Hynix Registered Dual In-Line Memory Module (DIMM) series consists of 1Gb version E DDR2 SDRAMs in Fine Ball Grid Array (FBGA) packages on a 240pin glass-epoxy substrate. This Hynix 1Gb version E based Registered DDR2 DIMM series provide a high performance 8 byte interface in 5.25" width form factor of industry standard. It is suitable for easy interchange and addition. FEATURES • JEDEC standard Double Data Rate2 Synchronous DRAMs (DDR2 SDRAMs) with 1.8V +/0.1V Power Supply All inputs and outputs are compatible with SSTL_1.8 interface 8 Bank architecture Posted CAS Programmable CAS Latency 3, 4, 5, 6 OCD (Off-Chip Driver Impedance Adjustment) ODT (On-Die Termination) • • • • • • • • Fully differential clock operations (CK & CK) Programmable Burst Length 4 / 8 with both sequential and interleave mode Auto refresh and self refresh supported 8192 refresh cycles / 64ms Serial presence detect with EEPROM DDR2 SDRAM Package: 60 ball(x4/x8) 133.35 x 30.00 mm form factor Halogen free & RoHS compliant • • • • • • ORDERING INFORMATION Part Name HMP112P7EFR8C-C4/Y5/S6/S5 HMP125P7EFR8C-C4/Y5/S6/S5 HMP125P7EFR4C-C4/Y5/S6/S5 HMP151P7EFR8C-C4/Y5/S6/S5 HMP151P7EFR4C-C4/Y5/S6/S5 HMP31GP7EMR4C-C4/Y5 Density Organization 1GB 2GB 2GB 4GB 4GB 8GB 128Mx72 256Mx72 256Mx72 512Mx72 512Mx72 512Mx72 # of DRAMs 9 18 18 36 36 72 # of ranks 1 2 1 4 2 4 Materials Halogen Free Halogen Free Halogen Free Halogen Free Halogen Free Halogen Free Parity Support O O O O O O This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 0.3 / Oct. 2008 1 1240pin Registered DDR2 SDRAM DIMMs SPEED GRADE & KEY PARAMETERS C4 (DDR2-533) Speed@CL3 Speed@CL4 Speed@CL5 Speed@CL6 CL-tRCD-tRP 400 533 4-4-4 Y5 (DDR2-667) 400 533 667 5-5-5 S6 (DDR2-800) 533 667 800 6-6-6 S5 (DDR2-800) 400 533 800 5-5-5 Unit Mbps Mbps Mbps Mbps tCK ADDRESS TABLE Density Organization 1GB 2GB 2GB 4GB 4GB 8GB 128M x 72 256M x 72 256M x 72 512M x 72 512M x 72 1G x 72 Ranks 1 2 1 4 2 4 SDRAMs 128Mb x 8 128Mb x 8 256Mb x 4 128Mb x 8 256Mb x 4 256Mb x 4 # of DRAMs 9 18 18 36 36 72 # of row/bank/column Address 14(A0~A13)/3(BA0~BA2)/10(A0~A9) 14(A0~A13)/3(BA0~BA2)/10(A0~A9) 14(A0~A13)/3(BA0~BA2)/11(A0~A9,A11) 14(A0~A13)/3(BA0~BA2)/10(A0~A9) 14(A0~A13)/3(BA0~BA2)/11(A0~A9,A11) 14(A0~A13)/3(BA0~BA2)/11(A0~A9,A11) Refresh Method 8K / 64ms 8K / 64ms 8K / 64ms 8K / 64ms 8K / 64ms 8K / 64ms Rev. 0.3 / Oct. 2008 2 1240pin Registered DDR2 SDRAM DIMMs Input/Output Functional Description Symbol CK0 Type IN Polarity Positive Edge Negative Edge Active High Pin Description Positive line of the differential pair of system clock inputs that drives input to the on-DIMM PLL. CK0 IN Negative line of the differential pair of system clock inputs that drives input to the on-DIMM PLL. CKE[1:0] IN Activates the DDR2 SDRAM CK signal when high and deactivates the CK signal when low. By deactivating the clocks, CKE low initiates the Power Down mode or the Self Refresh mode. Enables the associated DDR2 SDRAM command decoder when low and disables the command decoder when high. When the command decoder is disabled, new commands are ignored but previous operations continue. Rank 0 is selected by S0; Rank 1 is selected by S1 On-Die Termination signals. When sampled at the positive rising edge of the clock. RAS,CAS and WE(ALONG WITH S) define the command being entered. Reference voltage for SSTL18 inputs Power supplies for the DDR2 SDRAM output buffers to provide improved noise immunity. For all current DDR2 unbuffered DIMM designs, VDDQ shares the same power plane as VDD pins. S[1:0] IN Active Low ODT[1:0] RAS, CAS, WE Vref VDDQ BA[2:0] IN IN Supply Supply IN Active High Active Low - Selects which DDR2 SDRAM internal bank of Eight is activated. During a Bank Activate command cycle, Address input difines the row address(RA0~RA13) During a Read or Write command cycle, Address input defines the column address when sampled at the cross point of the rising edge of CK and falling edge of CK. In addition to the column address, AP is used to invoke autoprecharge operation at the end of the burst read or write cycle. If AP is high., autoprecharge is selected and BA0-BAn defines the bank to be precharged. If AP is low, autoprecharge is disabled. During a Precharge command cycle., AP is used in conjunction with BA0-BAn to control which bank(s) to precharge. If AP is high, all banks will be precharged regardless of the state of BA0-BAn inputs. If AP is low, then BA0-BAn are used to define which bank to precharge. Data and Check Bit Input/Output pins. A[9:0],A10/AP A[13:11] IN - DQ[63:0], CB[7:0] IN - DM[8:0] IN Active High DM is an input mask signal for write data. Input data is masked when DM is sampled High coincident with that input data during a write access. DM is sampled on both edges of DQS. Although DM pins are input only, the DM loading matches the DQ and DQS loading. Power and ground for the DDR2 SDRAM input buffers, and core logic. VDD and VDDQ pins are tied to VDD/VDDQ planes on these modules. VDD,VSS Supply Positive Edge Negative Edge - DQS[17:0] I/O I/O Positive line of the differential data strobe for input and output data DQS[17:0] Negative line of the differential data strobe for input and output data SA[2:0] IN These signals are tied at the system planar to either VSS or VDDSPD to configure the serial SPD EEPROM address range. This is a bidirectional pin used to transfer data into or out of the SPD EEPROM. A resister may be connected from the SDA bus line to VDDSPD on the system planar to act as a pull up. This signal is used to clock data into and out of the SPD EEPROM. A resistor may be connected from SCL to VDDSPD to act as a pull up on the system board. Power supply for SPD EEPROM. This supply is separate from the VDD/VDDQ power plane. EEPROM supply is operable from 1.7V to 3.6V. The RESET pin is connected to the RST pin on the register and to the OE pin on the PLL. When low, all register outputs will be driven low and the PLL clocks to the DRAMs and register(s) will be set to low level (the PLL will remain synchronized with the input clock) Parity bit for the Address and Control bus(“1”. Odd, “0”.Even) Parity error found in the Address and Control bus Used by memory bus analysis tools (unused on memory DIMMs) SDA I/O - SCL IN - VDDSPD Supply RESET IN Par_In Err_Out TEST IN OUT Rev. 0.3 / Oct. 2008 3 1240pin Registered DDR2 SDRAM DIMMs PIN DESCRIPTION Pin CK0 CK0 CKE0~CKE1 RAS CAS WE S0,S1 A0~A9,A11~A13 A10/AP BA0, BA1, BA2 SCL SDA SA0~SA2 Par_In Err_Out RESET CB0~CB7 Pin Description Clock Input, positive line Clock input, negative line Clock Enable Input Row Address Strobe Column Address Strobe Write Enable Chip Select Input Address input Address input/Autoprecharge SDRAM Bank Address Serial Presence Detect (SPD) Clock Input SPD Data Input/Output E2PROM Address Inputs Parity bit for the Address and Control bus Parity error found on the Address Reset Enable Data Strobe Inputs/Outputs Pin ODT[1:0] VDDQ DQ0~DQ63 CB0~CB7 DQS(0~8) DQS(0~8) DM(0~8),DQS(9~17) DQS(9~17) RFU NC TEST VDD VDDQ VSS VREF VDDSPD Pin Description On Die Termination Inputs DQs Power Supply Data Input/Output Data check bits Input/Output Data strobes Data strobes, negative line Data Maskes/Data strobes Data strobes, negative line Reserved for Future Use No Connect Memory bus test tool (Not Connected and Not Usable on DIMMs) Core Power I/O Power Supply Ground Reference Power Supply Power Supply for SPD PIN LOCATION pin #1 Front Side Pin #64 Pin #65 Pin #120 Pin #121 Back Side Pin #184 Pin #185 pin #240 Rev. 0.3 / Oct. 2008 4 1240pin Registered DDR2 SDRAM DIMMs PIN ASSIGNMENT Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Name VREF VSS DQ0 DQ1 VSS DQS0 DQS0 VSS DQ2 DQ3 VSS DQ8 DQ9 VSS DQS1 DQS1 VSS RESET NC VSS DQ10 DQ11 VSS DQ16 DQ17 VSS DQS2 DQS2 VSS DQ18 DQ19 VSS DQ24 DQ25 VSS DQS3 DQS3 VSS DQ26 DQ27 Pin 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Name VSS CB0 CB1 VSS DQS8 DQS8 VSS CB2 CB3 VSS VDDQ CKE0 VDD BA2,NC NC, Err_Out VDDQ A11 A7 VDD A5 A4 VDDQ A2 VDD Key Pin 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 Name DQ33 VSS DQS4 DQS4 VSS DQ34 DQ35 VSS DQ40 DQ41 VSS DQS5 DQS5 VSS DQ42 DQ43 VSS DQ48 DQ49 VSS SA2 NC(TEST) VSS DQS6 DQS6 VSS DQ50 DQ51 VSS DQ56 DQ57 VSS DQS7 DQS7 VSS DQ58 DQ59 VSS SDA SCL Pin 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 Name VSS DQ4 DQ5 VSS DM0/DQS9 DQS9 VSS DQ6 DQ7 VSS DQ12 DQ13 VSS DM1/DQS10 DQS10 VSS RFU RFU VSS DQ14 DQ15 VSS DQ20 DQ21 VSS DM2/DQS11 DQS11 VSS DQ22 DQ23 VSS DQ28 DQ29 VSS DM3/DQS12 DQS12 VSS DQ30 DQ31 VSS Pin 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 Name CB4 CB5 VSS DM8,DQS17 DQS17 VSS CB6 CB7 VSS VDDQ NC,CKE1 VDD A15,NC A14,NC VDDQ A12 A9 VDD A8 A6 VDDQ A3 A1 VDD Key Pin 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 Name VSS DM4/DQS13 DQS13 VSS DQ38 DQ39 VSS DQ44 DQ45 VSS DM5/DQS14 DQS14 VSS DQ46 DQ47 VSS DQ52 DQ53 VSS RFU RFU VSS DM6/DQS15 NC,DQS15 VSS DQ54 DQ55 VSS DQ60 DQ61 VSS DM7/DQS16 NC,DQS16 VSS DQ62 DQ63 VSS VDDSPD SA0 SA1 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 VSS VSS VDD NC, Err_Out VDD A10/AP BA0 VDDQ WE CAS VDDQ NC, S1 NC, ODT1 VDDQ VSS DQ32 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 CK0 CK0 VDD A0 VDD BA1 VDDQ RAS S0 VDDQ ODT0 A13,NC VDD VSS DQ36 DQ37 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 NC= No Connect, RFU= Reserved for Future Use. Note: 1. RESET (Pin 18) is connected to both OE of PLL and Reset of register. 2. NC/Err_out (Pin 55) and NC/Par_In(Pin68) are for optional function to check address and command parity. 3. The Test pin (Pin 102) is reserved for bus analysis probes and is not connected on normal memory modules (DIMMs) Rev. 0.3 / Oct. 2008 5 1240pin Registered DDR2 SDRAM DIMMs FUNCTIONAL BLOCK DIAGRAM 1GB(128Mbx72): HMP112P7EFR8C RS0 DQS0 DQS0 DM0/DQS9 DQS9 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DQS4 DQS4 DM4/DQS13 DQS13 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQS1 DQS1 DM1/DQS10 DQS10 D0 DQ32 DQ33 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQS5 DQS5 DM5/DQS14 DQS14 D4 Serial PD SCL WP A0 A1 A2 SA0 SA1 SA2 SDA DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQS2 DQS2 DM2/DQS11 DQS11 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D1 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DQS6 DQS6 DM6/DQS15 DQS15 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 VDDSPD VDD/VDDQ VREF VSS SPD D0–D8 D0–D8 D0–D8 D5 Note: 1. DQ-to-I/O wiring may be changed within a nibble. 2. Unless otherwise noted, resistor values are 22 Ohms ± 5%. DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQS3 DQS3 DM3DQS12 DQS12 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D2 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQS7 DQS7 DM7/DQS16 DQS16 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D6 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQS8 DQS8 DM8/DQS17 DQS17 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D3 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D7 CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D8 The resistors on Par_In,A13,A14,A15,BA2 and the signal line of Err_Out refer to the section: “Register Options for Unused Address inputs” Signals for Address and Command Parity Function Register Vss VSS PAR_IN 100KΩ C0 C1 PAR_IN PPO QERR Err_Out S0* BA0-BA2** A0-A15** RAS CAS WE CKE0 ODT1 RESET PCK7 1:2 R E G I S T R E RST RS0 -> CS: SDRAMs D0-D8 RBA-RBA2 -> BA0-BA2: SDRAMs D0-D8 RA0-RA15 -> A0-A15: SDRAMs D0-D8 RRAS -> RAS: SDRAMs D0-D8 RCAS -> CAS: SDRAMs D0-D8 RWE -> WE: SDRAMs D0-D8 RCKE0 -> CKE0: SDRAMs D0-D8 RODT0 -> ODT0: SDRAMs D0-D8 CK0 CK0 RESET P L L OE PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D8 PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D8 PCK7 -> CK: Register PCK7 -> CK: Register PCK7 * S0 connects to DCS of VDD connects to CSR on the register. S1, CKE1 and ODT1 are NC. ** A13-15, BA2 have the optional pull down resistors (100K ohms), which is not indicated here. Rev. 0.3 / Oct. 2008 6 1240pin Registered DDR2 SDRAM DIMMs FUNCTIONAL BLOCK DIAGRAM 2GB(256Mbx72) : HMP125P7EFR8C RS1 RS0 DQS0 DQS0 DM0/DQS9 DQS9 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DQS4 DQS4 DM4/DQS13 DQS13 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQS1 DQS1 DM1/DQS10 DQS10 D0 D9 DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQS5 DQS5 DM5/DQS14 DQS14 D4 D13 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQS2 DQS2 DM2/DQS11 DQS11 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D1 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D10 DQ40 DQ41 DQ42 DQ43 DQ40 DQ41 DQ42 DQ43 DQS6 DQS6 DM6/DQS15 DQS15 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D5 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D14 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQS3 DQS3 DM3/DQS12 DQS12 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D2 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D11 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQS7 DQS7 DM7/DQS16 DQS16 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D6 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D15 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQS8 DQS8 DM8DQS17 DQS17 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D3 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D12 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 Serial PD SCL DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D7 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D16 VDDSPD SDA SPD D0–D17 D0–D17 D0–D17 VDD/VDDQ VREF VSS CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D8 DM/ NU/ CS DQS DQS RDQS RDQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 WP A0 A1 A2 SA0 SA1 SA2 D17 CK0 CK0 RESET P L L OE PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D17 PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D17 PCK7 -> CK: Register PCK7 -> CK: Register Signals for Address and Command Parity Function S0* S1* BA0-BA2*** A0-A15*** RAS CAS WE CKE0 CKE1 ODT0 ODT1 RESET** PCK7** PCK7** 1:2 R E G I S T R E R RST Register A Register B RS0 -> CS: SDRAMs D0-D8 C0 C0 Vss VDD RS1 -> CS: SDRAMs D9-D17 VDD C1 VDD C1 RBA0-RBA2 -> BA0-BA2: SDRAMs D0-D17 PAR_IN PPO PPO PAR_IN PAR_IN RA0-RA15 -> A0-A15: SDRAMs D0-D17 100KΩ QERR QERR Err_Out RRAS -> RAS: SDRAMs D0-D17 RCAS -> CAS: SDRAMs D0-D17 The resistors on Par_In,A13,A14,A15,BA2 and the signal line of Err_Out refer to RWE -> WE: SDRAMs D0-D17 the section: “Register Options for Unused Address inputs” RCKE0 -> CKE0: SDRAMs D0-D8 RCKE1 -> CKE0: SDRAMs D9-D17 Note: RODT0 -> ODT0: SDRAMs D0-D8 1. DQ-to-I/O wiring may be changed within a byte. RODT1 -> ODT0: SDRAMs D9-D17 2. Unless otherwise noted, resistor values are 22 Ohms ± 5%. 3. RS0 and RS1 alternate between the back and front sides of the DIMM. * S0 connects to DCS and S1 connects to CSR on Registers. S1 connects to DCS and S0 connects to CSR on another Register. ** RESET, PCK7 and PCK7 connect to both Registers. Other signals connect to one of two Registers. *** A13-15, BA2 have the optional pull down resistors (100K ohms), which is not indicated here. Rev. 0.3 / Oct. 2008 7 1240pin Registered DDR2 SDRAM DIMMs FUNCTIONAL BLOCK DIAGRAM 2GB(256Mbx72): HMP125P7EFR4C VSS RS0 DQS0 DQS0 DM CS DQS DQS DQ0 DQ1 DQ2 DQ3 DQS1 DQS1 DQ8 DQ9 DQ10 DQ11 DQS2 DQS2 DQ16 DQ17 DQ18 DQ19 DQS3 DQS3 DQ24 DQ25 DQ26 DQ27 DQS4 DQS4 DQ32 DQ33 DQ34 DQ35 DQS5 DQS5 DQ40 DQ41 DQ42 DQ43 DQS6 DQS6 DQ48 DQ49 DQ50 DQ51 DQS7 DQS7 DQ56 DQ57 DQ58 DQ59 DQS8 DQS8 CB0 CB1 CB2 CB3 I/O 0 I/O 1 I/O 2 I/O 3 DQS9 DQS9 DM CS DQS DQS DQ4 DQ5 DQ6 DQ7 DQS9 DQS9 DQ12 DQ13 DQ14 DQ15 DQS11 DQS11 DQ20 DQ21 DQ22 DQ23 DQS12 DQS12 DQ28 DQ29 DQ30 DQ31 DQS13 DQS13 DQ36 DQ37 DQ38 DQ39 DQS14 DQS14 DQ44 DQ45 DQ46 DQ47 DQS15 DQS15 DQ52 DQ53 DQ54 DQ55 DQS16 DQS16 DQ60 DQ61 DQ62 DQ63 DQS17 DQS17 CB4 CB5 CB6 CB7 I/O 0 I/O 1 I/O 2 I/O 3 SCL WP A0 A1 A2 SA0 SA1 SA2 Serial PD SDA D0 D9 VDDSPD DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 SPD D0–D17 D0–D17 D0–D17 VDD/VDDQ VREF VSS D1 D10 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D2 D11 CK0 CK0 RESET P L L OE PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D17 PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D17 PCK7 -> CK: Register PCK7 -> CK: Register DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D3 D12 Note: 1. DQ-to-I/O wiring may be changed within a nibble. 2. Unless otherwise noted, resistor values are 22 Ohms ± 5%. DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D4 D13 * S0 connects to DCS of Register A and CSR of Register B. CSR of Register A and DCS of Register B connects to VDD. ** RESET, PCK7 and PCK7 connects to both Registers. Other signals connect to one of two Registers. *** A13-15, BA2 have the optional pull down resistors (100K ohms), which is not indicated here. DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D5 D14 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D6 D15 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D7 D16 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D8 D17 S0* BA0-BA2*** A0-A15*** RAS CAS WE CKE0 ODT1 RESET** PCK7** 1:2 R E G I S T R E RST RS0 -> CS: SDRAMs D0-D17 RBA-RBA2 -> BA0-BA2: SDRAMs D0-D17 RA0-RA15 -> A0-A15: SDRAMs D0-D17 RRAS -> RAS: SDRAMs D0-D17 RCAS -> CAS: SDRAMs D0-D17 RWE -> WE: SDRAMs D0-D17 RCKE0 -> CKE0: SDRAMs D0-D17 RODT0 -> ODT0: SDRAMs D0-D17 The resistors on Par_In,A13,A14,A15,BA2 and the signal line of Err_Out refer to the section: “Register Options for Unused Address inputs” Signals for Address and Command Parity Function Register A Vss VDD PAR_IN 100KΩ C0 C1 PAR_IN PPO QERR VDD VDD C0 C1 PAR_IN PPO QERR Err_Out Register B PCK7** Rev. 0.3 / Oct. 2008 8 1240pin Registered DDR2 SDRAM DIMMs FUNCTIONAL BLOCK DIAGRAM 4GB(512Mbx72) : HMP151P7EFR8C RDOT0 RCKE0 RS0 ODT CS DQS0 DQS0 DQ7-0 DM0 DQS1 DQS1 DQ15-8 DM1 DQS2 DQS2 DQ23-16 DM2 DQS3 DQS3 DQ31-24 DM3 DQS4 DQS4 CB7-0 DM8 DQS4 DQS4 DQ39-32 DM4 DQS5 DQS5 DQ47-40 DM5 DQS6 DQS6 DQ55-48 DM6 DQS7 DQS7 DQ63-56 DM7 DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM CKE RDOT1 RCKE1 RS2 ODT ODT CS CS DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM CKE CKE RS1 RS3 Serial PD DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM DQS DQS DQ7-0 DM ODT CS CKE SCL WP A0 A1 A2 SDA D0 ODT CS CKE D9 ODT CS CKE D18 ODT CS CKE D27 ODT CS CKE SA0 SA1 SA2 D1 ODT CS CKE D10 ODT CS CKE D19 ODT CS CKE D28 ODT CS CKE VDDSPD VDD/VDDQ VREF VSS SPD D0–D35 D0–D35 D0–D35 D2 ODT CS CKE D11 ODT CS CKE D20 ODT CS CKE D29 ODT CS CKE CK0 P CK0 L L PCK0-PCK6, PCK8,PCK9 -> CK: SDRAMs D0-D35 PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D35 PCK7 -> CK: Register PCK7 -> CK: Register D3 ODT CS CKE D12 ODT CS CKE D21 ODT CS CKE D30 ODT CS CKE D4 ODT CS CKE D13 ODT CS CKE D22 ODT CS CKE D31 ODT CS CKE RESET OE Signals for Address and Command Parity Function Register A1 Vss C0 C1 PAR_IN PPO QERR D5 ODT CS CKE D14 ODT CS CKE D23 ODT CS CKE D32 ODT CS CKE VDD D6 ODT CS CKE D15 ODT CS CKE D24 ODT CS CKE D33 ODT CS CKE VDD VDD C0 C1 PAR_IN Register B1 D7 ODT CS CKE D16 ODT CS CKE D25 ODT CS CKE PPO QERR D34 ODT CS CKE Vss VDD Register A2 C0 C1 PAR_IN PPO QERR Err_Out D8 D17 D26 D35 S0,S2* S1,S3* BA0-BA2*** A0-A15*** RAS CAS WE CKE0 CKE1 ODT0 ODT1 RESET** PCK7** PCK7** 1:2 R E G I S T E R RST RS0 -> CS: SDRAMs D0-D8, RS2 -> CS: SDRAMs D18-D26 RS1 -> CS: SDRAMs D9-D17,RS3 -> CS: SDRAMs D27-D35 RBA0-RBA2 -> BA0-BA2: SDRAMs D0-D35**** RA0-RA15 -> A0-A15: SDRAMs D0-D35**** RRAS -> RAS: SDRAMs D0-D35 RCAS -> CAS: SDRAMs D0-D35 RWE -> WE: SDRAMs D0-D35 RCKE0 -> CKE: SDRAMs D0-D17 RCKE1 -> CKE: SDRAMs D18-D35 RODT0 -> ODT0: SDRAMs D0-D8 RODT1 -> ODT1: SDRAMs D18-D26 VDD VDD C0 Register B2 C1 PAR_IN PPO QERR Register A1 and A2 share the a part of Addr/Cmd input signal set. Register B1 and B2 chare the rest part of Addr/Cmd input signal set. The resistors on Par_In, A13, A14. A15,BA2 and the signal line of Err_Out refer to the section: The egister Options for Unused Address inputs? * S0 (S2) connects to DCS0, S1 (S3) to DCS1 on a Register A. S1 (S3) connects to DCS and S0 (S2) connects to CSR on another pair of Register. * S2 and S3 have required upll up resistors (100k ohms), not indicated here. ** RESET, PCK7 and PCK7 connect to all Registers. Other signals connect to two of four Registers. *** A13-15, BA2 have the optional pull down resistors(100K ohms), which is not indicated here. **** For Raw Card N2, DQ stub resistor value is TBD. And for Raw Card N2, post register A14 and A15 are not connected to the SDRAMs. Rev. 0.3 / Oct. 2008 9 1240pin Registered DDR2 SDRAM DIMMs FUNCTIONAL BLOCK DIAGRAM 4GB(512Mbx72): HMP151P7EFR4C VSS RS0 RS1 DQS0 DQS0 DM CS DQS DQS DQ0 DQ1 DQ2 DQ3 DQS1 DQS1 DQ8 DQ9 DQ10 DQ11 DQS2 DQS2 DQ16 DQ17 DQ18 DQ19 DQS3 DQS3 DM CS DQS DQS DQ24 DQ25 DQ26 DQ27 DQS8 DQS8 DM CS DQS DQS CB0 CB1 CB2 CB3 RS0 RS1 DQS4 DQS4 DM CS DQS DQS DQ32 DQ33 DQ34 DQ35 DQS5 DQS5 DQ40 DQ41 DQ42 DQ43 DQS6 DQS6 DQ48 DQ49 DQ50 DQ51 DQS7 DQS7 DM CS DQS DQS DQ56 DQ57 DQ58 DQ59 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS9 DQS9 DM CS DQS DQS DQ4 DQ5 DQ6 DQ7 DQS10 DQS10 DQ12 DQ13 DQ14 DQ15 DQS11 DQS11 DQ20 DQ21 DQ22 DQ23 DQS12 DQS12 DM CS DQS DQS DQ28 DQ29 DQ30 DQ30 DQS17 DQS17 DM CS DQS DQS CB4 CB5 CB6 CB7 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D0 D18 D9 D27 Serial PD SCL WP A0 A1 A2 SDA DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 SA0 SA1 SA2 D1 D19 D10 D28 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 VDDSPD VDD/VDDQ VREF VSS SPD D0–D35 D0–D35 D0–D35 D2 D20 D11 D29 D3 D21 D12 D30 D8 D26 D17 D35 Signals for Address and Command Parity Function Register Par_In PARIN PTYERR 0Ω Register DQS13 DQS13 DM CS DQS DQS DQ36 DQ37 DQ38 DQ39 DQS14 DQS14 DQ44 DQ45 DQ46 DQ47 DQS15 DQS15 DQ52 DQ53 DQ54 DQ55 DQS16 DQS16 DM CS DQS DQS DQ60 DQ61 DQ62 DQ63 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 100KΩ PARIN PTYERR Err_Out D4 D22 D13 D31 o ohm resistor on Err_Out is not populated for non-parity card. The resistors on Par_In,A13,A14,A15,BA2 and the signal line of Err_Out refer to the section: “Register Options for Unused Address input” DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D5 D23 D14 D32 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 DM CS DQS DQS I/O 0 I/O 1 I/O 2 I/O 3 D6 D24 D15 D33 D7 D25 D16 D34 S0* S1* BA0-BA2*** A0-A15*** RAS CAS WE CKE0 CKE1 ODT0 ODT1 RESET** PCK7** PCK7** 1:2 R E G I S T E R RST RS0 -> CS: SDRAMs D0-D17 RS1 -> CS: SDRAMs D18-D35 RBA0-RBA2 -> BA0-BA2: SDRAMs D0-D35 RA0-RA15 -> A0-A15: SDRAMs D0-D35 RRAS -> RAS: SDRAMs D0-D35 RCAS -> CAS: SDRAMs D0-D35 RWE -> WE: SDRAMs D0-D35 RCKE0 -> CKE0-1: SDRAMs D0-D17 RCKE1 -> CKE0-1: SDRAMs D18-D35 RODT0 -> ODT1: SDRAMs D0-D17 RODT1 -> ODT1: SDRAMs D18-D35 CK0 CK0 RESET P L L OE PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D35 PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D35 PCK7 -> CK: Register PCK7 -> CK: Register Note: 1. DQ-to-I/O wiring may be changed within a nibble. 2. Unless otherwise noted, resistor values are 22 Ohms ± 5%. 3. RS0 and RS1 alternate between the bottom and surface sides of the DIMM. *S0 connects to DCS and S1 command to CRS on a pair of Register, S2 connects to DCS and S0 connect to CRS on another pair of Register. ** RESET, PCK7 and PCK7 connect to all Registers. Other signals connect to one pair of four Registers. *** A14-15, BA2 have the optional pull down resistors (100K ohms), which is not indicated here. Rev. 0.3 / Oct. 2008 10 1240pin Registered DDR2 SDRAM DIMMs FUNCTIONAL BLOCK DIAGRAM 8GB(1Gbx72): HMP31GP7EFR4C RODT0 RCKE0 RS1 RS0 22Ω CS0 CS1 CKE0 CKE1 ODT0 ODT1 CS0 CS1 CKE0 CKE1 ODT0 ODT1 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS0 DQS0 DQ3~0 DQS DQS DQ3~0 DM DQS DQS DQ3~0 DM DQS9 DQS9 DQ7~4 DQS DQS DQ3~0 DM DQS DQS DQ3~0 DM CS0 CS1 CKE0 CKE1 ODT0 ODT1 RODT1 RCKE1 RS3 RS2 RODT0 RCKE0 RS1 RS0 RODT1 RCKE1 RS3 RS2 D0 CS0 CS1 CKE0 CKE1 ODT0 ODT1 D18 CS0 CS1 CKE0 CKE1 ODT0 ODT1 D9 CS0 CS1 CKE0 CKE1 ODT0 ODT1 D27 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS1 DQS1 DQ11~8 DQS DQS DQ3~0 DM D1 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D19 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS10 DQS10 DQ15~12 DQS DQS DQ3~0 DM D10 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D28 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS2 DQS2 DQ19~26 DQS DQS DQ3~0 DM D2 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D20 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS11 DQS11 DQ23~20 DQS DQS DQ3~0 DM D11 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D29 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS3 DQS3 DQ27~24 DQS DQS DQ3~0 DM D3 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D21 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS12 DQS12 DQ31~28 DQS DQS DQ3~0 DM D12 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D30 D0 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS8 DQS8 CB3~0 DQS DQS DQ3~0 DM D8 RODT1 RCKE1 RS3 RS2 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D26 DQS17 DQS17 CB7~4 DQS DQS DQ3~0 DM D17 RODT1 RCKE1 RS3 RS2 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D35 RODT0 RCKE0 RS1 RS0 DQS4 DQS4 DQ35~32 22Ω DQS5 DQS5 DQ43~40 DQS DQS DQ3~0 DM RODT0 RCKE0 RS1 RS0 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM DQS13 DQS13 DQ39~36 DQS DQS DQ3~0 DM D4 CS0 CS1 CKE0 CKE1 ODT0 ODT1 D22 CS0 CS1 CKE0 CKE1 ODT0 ODT1 D13 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D31 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D5 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D23 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS14 DQS14 DQ47~44 DQS DQS DQ3~0 DM D14 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D32 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS6 DQ51~48 DQS DQS DQ3~0 DM D6 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D24 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS15 DQS15 DQ55~52 DQS DQS DQ3~0 DM D15 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS DQS DQ3~0 DM D33 CS0 CS1 CKE0 CKE1 ODT0 ODT1 DQS7 DQS7 DQ59~56 DQS DQS DQ3~0 DM D7 DQS DQS DQ3~0 DM D25 DQS16 DQS16 DQ63~60 DQS DQS DQ3~0 DM D16 DQS DQS DQ3~0 DM D34 22Ω Register RS0 -> CS0: SDRAMs D0-D17, RS2 -> CS0: SDRAMs D18-D35 1:2 R E G I S T E R RST S0,2* S1,3** BA0-BA2*** A0-A15*** RAS CAS WE CKE0 CKE1 ODT1 ODT0 RESET PCK7 PCK7 RS1 -> CS1: SDRAMs D0-D17, RS3 -> CS1: SDRAMs D18-D35 RBA-RBA2 -> BA0-BA1: SDRAMs D0-D35 RA0-RA13 -> A0-A13: SDRAMs D0-D35 RRAS -> RAS: SDRAMs D0-D35 RCAS -> CAS: SDRAMs D0-D35 RWE -> WE: SDRAMs D0-D35 RCKE0 -> CKE0-1: SDRAMs D0-D17 RCKE1 -> CKE0-1: SDRAMs D18-D35 RODT0 -> ODT1: SDRAMs D0-D17 RODT1 -> ODT1: SDRAMs D18-D35 CK0 CK0 RESET P L L OE 0Ω PAR_IN 100KΩ PARIN PTYERR 0Ω ERR_OUT Serial PD Register PARIN PTYERR SCL CS0 CS1 CKE0 CKE1 ODT0 ODT1 SDA WP A0 A1 A2 SA0 SA1 SA2 PCK7 -> CK: Register PCK7 -> CK: Register PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D35 PCK0-PCK6, PCK8, PCK9 -> CK: SDRAMs D0-D35 *S0 connects to DCS0, S1 to DCS1 on the first register, S2 connects to DCS0, S3 to DCS1 on the second register. ** S2 and S3 have required pull up resistors (100K ohms), not indicated here. *** A13-15, BA2 have optional pull down resistors (100K ohms), not indicated here. Rev. 0.3 / Oct. 2008 11 1240pin Registered DDR2 SDRAM DIMMs ABSOLUTE MAXIMUM DC RATINGS Parameter Voltage on VDD pin relative to Vss Voltage on VDDQ pin relative to Vss Voltage on VDDL pin relative to Vss Voltage on any pin relative to Vss Symbol VDD VDDQ VDDL VIN, VOUT Value - 1.0 ~ 2.3 - 0.5 ~ 2.3 - 0.5 ~ 2.3 - 0.5 ~ 2.3 Unit V V V V Note 1 1 1 1 Operating Conditions and Environmental Parameters Parameter DIMM Operating temperature (ambient) Storage Temperature Storage Humidity (without condensation) DIMM Barometric Pressure (operating & storage) DRAM Component Case Temperature Range Note: 1. Stress greater than those listed may cause permanent damage to the device. This is a stress rating only, and device functional operation at or above the conditions indicated is not implied. Expousure to absolute maximum rating con ditions for extended periods may affect reliablility. 2. Up to 9850 ft. 3. If the DRAM case temperature is Above 85oC, the Auto-Refresh command interval has to be reduced to tREFI=3.9us. For Measurement conditions of TCASE, please refer to the JEDEC document JESD51-2. Symbol TOPR TSTG HSTG PBAR TCASE Rating 0 ~ +55 -50 ~ +100 5 to 95 105 to 69 0 ~+95 Units o o Notes C C 1 1 2 3 % K Pascal oC DC OPERATING CONDITIONS Symbol VDD VDDL VDDQ VREF VTT VDDSPD Note: Parameter Supply Voltage Supply Voltage for DLL Supply Voltage for Output Input Reference Voltage Termination Voltage EEPROM Supply Voltage (SSTL_1.8) Rating Min. 1.7 1.7 1.7 0.49*VDDQ VREF-0.04 1.7 Typ. 1.8 1.8 1.8 0.50*VDDQ VREF Max. 1.9 1.9 1.9 0.51*VDDQ VREF+0.04 3.6 Units V V V mV V V Notes 1 1,2 1,2 3,4 5 1. Min. Typ. and Max. values increase by 100mV for C3(DDR2-533 3-3-3) speed option. 2. VDDQ tracks with VDD,VDDL tracks with VDD. AC parameters are measured with VDD,VDDQ and VDD. 3. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the value of VREF is expected to be about 0.5 x VDDQ of the transmitting device and VREF is expected to track variations in VDDQ. 4. Peak to peak ac noise on VREF may not exceed +/-2% VREF (dc). 5. VTT of transmitting device must track VREF of receiving device. Rev. 0.3 / Oct. 2008 12 1240pin Registered DDR2 SDRAM DIMMs INPUT DC LOGIC LEVEL Parameter dc Input logic HIGH dc Input logic LOW Symbol VIH(DC) VIL(DC) Min VREF + 0.125 -0.30 Max VDDQ + 0.3 VREF - 0.125 Unit V V Note INPUT AC LOGIC LEVEL Parameter ac Input logic HIGH ac Input logic LOW Symbol VIH(AC) VIL(AC) DDR2 400/533 Min VREF + 0.250 Max VREF - 0.250 DDR2 667/800 Min VREF + 0.200 Max VREF - 0.200 Unit V V Notes AC INPUT TEST CONDITIONS Symbol VREF VSWING(MAX) SLEW Note: 1. 2. 3. Input waveform timing is referenced to the input signal crossing through the VREF level applied to the device under test. The input signal minimum slew rate is to be maintained over the range from VREF max to VIH(ac) min for rising edges and the range from VREF min to VIL(ac) max for falling edges as shown in the below figure. AC timings are referenced with input waveforms switching from VIL (ac) to VIH (ac) on the positive transitions and VIH (ac) to VIL (ac) on the negative transitions. Condition Input reference voltage Input signal maximum peak to peak swing Input signal minimum slew rate Value 0.5 * VDDQ 1.0 1.0 Units V V V/ns Notes 1 1 2, 3 Start of Falling Edge Input Timing Start of Rising Edge Input Timing VSWING(MAX) VDDQ VIH(ac) min VIH(dc) min VREF VIL(dc) max VIL(ac) max VSS VIH(ac) min - VREF ∆TF Falling Slew = VREF - VIL(ac) max ∆TR ∆TF Rising Slew = ∆TR < Figure: AC Input Test Signal Waveform > Rev. 0.3 / Oct. 2008 13 1240pin Registered DDR2 SDRAM DIMMs Differential Input AC logic Level Symbol VID (ac) VIX (ac) Note: 1. VIN(DC) specifies the allowable DC execution of each input of differential pair such as CK, CK, DQS, DQS, LDQS, LDQS, UDQS and UDQS. 2. VID(DC) specifies the input differential voltage |VTR -VCP | required for switching, where VTR is the true input (such as CK, DQS, LDQS or UDQS) level and VCP is the complementary input (such as CK, DQS, LDQS or UDQS) level. The minimum value is equal to VIH(DC) - VIL(DC). Parameter ac differential input voltage ac differential cross point voltage Min. 0.5 0.5 * VDDQ - 0.175 Max. VDDQ + 0.6 0.5 * VDDQ + 0.175 Units V V Note 1 2 VDDQ VTR VID VCP VSSQ < Differential signal levels > Note: 1. VID(AC) specifies the input differential voltage |VTR -VCP | required for switching, where VTR is the true input signal (such as CK, DQS, LDQS or UDQS) and VCP is the complementary input signal (such as CK, DQS, LDQS or UDQS). The minimum value is equal to V IH(AC) - VIL(AC). 2. The typical value of VIX(AC) is expected to be about 0.5 * VDDQ of the transmitting device and VIX(AC) is expected to track variations in VDDQ. VIX(AC) indicates the voltage at which differential input signals must cross. Crossing point VIX or VOX DIFFERENTIAL AC OUTPUT PARAMETERS Symbol VOX (ac) Note: 1. The typical value of VOX(AC) is expected to be about 0.5 * VDDQ of the transmitting device and VOX(AC) is expected to track variations in VDDQ. VOX(AC) indicates the voltage at which differential output signals must cross. Parameter ac differential crosspoint voltage Min. 0.5 * VDDQ - 0.125 Max. 0.5 * VDDQ + 0.125 Units V Note 1 Rev. 0.3 / Oct. 2008 14 1240pin Registered DDR2 SDRAM DIMMs OUTPUT BUFFER LEVELS OUTPUT AC TEST CONDITIONS Symbol VOTR Note: 1. The VDDQ of the device under test is referenced. Parameter Output Timing Measurement Reference Level SSTL_18 0.5 * VDDQ Units V Notes 1 OUTPUT DC CURRENT DRIVE Symbol IOH(dc) IOL(dc) Note: 1.VDDQ = 1.7 V; VOUT = 1420 mV. (VOUT - VDDQ)/IOH must be less than 21 ohm for values of VOUT between VDDQ and VDDQ - 280 mV. 2. VDDQ = 1.7 V; VOUT = 280 mV. VOUT/IOL must be less than 21 ohm for values of VOUT between 0 V and 280 mV. 3. The dc value of VREF applied to the receiving device is set to VTT 4. The values of IOH(dc) and IOL(dc) are based on the conditions given in Notes 1 and 2. They are used to test device drive current capability to ensure VIH min plus a noise margin and VIL max minus a noise margin are delivered to an SSTL_18 receiver. The actual current values are derived by shifting the desired driver operating point along a 21 ohm load line to define a convenient driver current for measurement. Parameter Output Minimum Source DC Current Output Minimum Sink DC Current SSTl_18 - 13.4 13.4 Units mA mA Notes 1, 3, 4 2, 3, 4 Rev. 0.3 / Oct. 2008 15 1240pin Registered DDR2 SDRAM DIMMs PIN Capacitance (VDD=1.8V,VDDQ=1.8V, TA=25°C) 1GB: HMP112P7EFR8C Pin CK0, /CK0 CKE, ODT /CS Address, /RAS, /CAS, /WE DQ, DM, DQS, /DQS Symbol CCK CI1 CI2 CI3 CIO Min 7 8 8 8 6 Max 11 12 12 12 9 Unit pF pF pF pF pF 2GB: HMP125P7EFR8C Pin CK0, /CK0 CKE, ODT /CS Address, /RAS, /CAS, /WE DQ, DM, DQS, /DQS Symbol CCK CI1 CI2 CI3 CIO Min 7 8 10 8 6 Max 11 12 15 12 9 Unit pF pF pF pF pF 2GB: HMP125P7EFR4C Pin CK0, /CK0 CKE, ODT /CS Address, /RAS, /CAS, /WE DQ, DM, DQS, /DQS Symbol CCK CI1 CI2 CI3 CIO Min 7 8 10 8 6 Max 11 12 15 12 9 Unit pF pF pF pF pF 4GB: HMP151P7EFR8C Pin CK0, /CK0 CKE, ODT /CS Address, /RAS, /CAS, /WE DQ, DM, DQS, /DQS Symbol CCK CI1 CI2 CI3 CIO Min 7 10 10 10 9 Max 11 15 15 15 15 Unit pF pF pF pF pF Rev. 0.3 / Oct. 2008 16 1240pin Registered DDR2 SDRAM DIMMs 4GB: HMP151P7EFR4C Pin CK0, /CK0 CKE, ODT /CS Address, /RAS, /CAS, /WE DQ, DM, DQS, /DQS Symbol CCK CI1 CI2 CI3 CIO Min 7 10 10 10 9 Max 11 15 15 15 15 Unit pF pF pF pF pF 8GB: HMP31GP7EMR4C Pin CK0, /CK0 CKE, ODT /CS Address, /RAS, /CAS, /WE DQ, DM, DQS, /DQS Note: 1. Pins not under test are tied to GND. 2. These value are guaranteed by design and tested on a sample basis only. Symbol CCK CI1 CI2 CI3 CIO Min 7 8 8 10 18 Max 11 12 12 15 22 Unit pF pF pF pF pF Rev. 0.3 / Oct. 2008 17 1240pin Registered DDR2 SDRAM DIMMs IDD SPECIFICATIONS (TCASE: 0 to 95oC) 1GB, 128M x 72 Registered DIMM: HMP112P7EFR8C Symbol IDD0 IDD1 IDD2P IDD2Q IDD2N IDD3P(F) IDD3P(S) IDD3N IDD4R IDD4W IDD5B IDD6 IDD7 C4 (DDR2 533@CL4) 1235 1325 740 893 965 875 758 1055 1730 1730 2090 540 2225 Y5 (DDR2 667@CL5) 1280 1370 740 920 1010 875 758 1100 1910 1955 2135 540 2405 S5 /S6 (DDR2 800@CL5&6) 1325 1415 740 938 1055 875 758 1145 2090 2180 2180 540 2720 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA Note 1 2GB, 256M x 72 Registered DIMM: HMP125P7EFR8C Symbol IDD0 IDD1 IDD2P IDD2Q IDD2N IDD3P(F) IDD3P(S) IDD3N IDD4R IDD4W IDD5B IDD6 IDD7 C4 (DDR2 533@CL4) 1550 1640 830 1136 1280 1100 866 1460 2045 2045 1405 630 2675 Y5 (DDR2 667@CL5) 1640 1730 830 1190 1370 1100 866 1550 2270 2315 2495 630 2765 S5 /S6 (DDR2 800@CL5&6) 1730 1820 830 1226 1460 1100 866 1640 2495 2585 1585 630 3125 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA Note 1 Rev. 0.3 / Oct. 2008 18 1240pin Registered DDR2 SDRAM DIMMs 2GB, 256M x 72 Registered DIMM: HMP125P7EFR4C Symbol IDD0 IDD1 IDD2P IDD2Q IDD2N IDD3P(F) IDD3P(S) IDD3N IDD4R IDD4W IDD5B IDD6 IDD7 C4 (DDR2 533@CL4) 1280 2000 830 1136 1280 1100 866 1460 2810 2810 3330 630 4070 Y5 (DDR2 667@CL5) 1910 2090 830 1190 1370 1100 866 1550 3170 3260 3420 630 4160 S5 /S6 (DDR2 800@CL5&6) 2000 2180 830 1226 1460 1100 866 1640 3530 3710 3510 630 4790 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA Note 1 4GB, 512M x 72 Registered DIMM: HMP151P7EFR8C Symbol IDD0 IDD1 IDD2P IDD2Q IDD2N IDD3P(F) IDD3P(S) IDD3N IDD4R IDD4W IDD5B IDD6 IDD7 C4 (DDR2 533@CL4) 2180 2270 690 758 790 750 698 830 2675 2675 5420 490 3305 Y5 (DDR2 667@CL5) 2360 2450 690 770 810 750 698 850 2290 3035 5780 490 3485 S5 /S6 (DDR2 800@CL5&6) 2540 2630 690 778 830 750 698 870 3305 3395 6140 490 3935 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA Note 1 Rev. 0.3 / Oct. 2008 19 1240pin Registered DDR2 SDRAM DIMMs 4GB, 512M x 72 Registered DIMM: HMP151P7EFR4C Symbol IDD0 IDD1 IDD2P IDD2Q IDD2N IDD3P(F) IDD3P(S) IDD3N IDD4R IDD4W IDD5B IDD6 IDD7 C4 (DDR2 533@CL4) 2450 2630 1010 1622 1910 1550 1082 2270 3440 3440 3960 810 4430 Y5 (DDR2 667@CL5) 2630 2810 1010 1730 2090 1550 1082 2450 3890 3980 4140 810 4880 S5 /S6 (DDR2 800@CL5&6) 2810 2990 1010 1802 2270 1550 1082 2630 4340 4520 4320 810 5600 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA Note 1 8GB, 1G x 72 Registered DIMM: HMP31GP7EMR4C Symbol IDD0 IDD1 IDD2P IDD2Q IDD2N IDD3P(F) IDD3P(S) IDD3N IDD4R IDD4W IDD5B IDD6 IDD7 C4 (DDR2 533@CL4) 3710 3890 690 758 790 750 698 830 4700 4700 5220 490 5690 Y5 (DDR2 667@CL5) 4070 4250 690 770 810 750 698 850 5330 5420 5580 490 6320 Unit mA mA mA mA mA mA mA mA mA mA mA mA mA Note Note: 1. IDD6 current values are guaranteed up to Tcase of 85°C max. Rev. 0.3 / Oct. 2008 20 1240pin Registered DDR2 SDRAM DIMMs IDD Measurement Conditions Symbol IDD0 Conditions Operating one bank active-precharge current; tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRASmin (IDD);CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus inputs are SWITCHING Operating one bank active-read-precharge current; IOUT = 0mA;BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin (IDD), tRCD = tRCD(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern is same as IDD4W Precharge power-down current; All banks idle; tCK = tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING Precharge quiet standby current; All banks idle; tCK = tCK(IDD);CKE is HIGH, CS is HIGH; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING Precharge standby current; All banks idle; tCK = tCK(IDD); CKE is HIGH, CS is HIGH; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING Active power-down current; All banks open; tCK = tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE; Data bus inputs are FLOATING Fast PDN Exit MRS(12) = 0 Slow PDN Exit MRS(12) = 1 Units mA IDD1 mA IDD2P IDD2Q IDD2N mA mA mA mA mA IDD3P IDD3N Active standby current; All banks open; tCK = tCK(IDD), tRAS = tRASmax (IDD), tRP =tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING Operating burst write current; All banks open, Continuous burst writes; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax (IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus inputs are SWITCHING Operating burst read current; All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax (IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern is same as IDD4W Burst refresh current; tCK = tCK(IDD); Refresh command at every tRFC(IDD) interval; CKE is HIGH, CS is HIGH between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING Self refresh current; CK and CK at 0V; CKE ≤ 0.2V; Other control and address bus inputs are FLOATING; Data bus inputs are FLOATING. IDD6 current values are guaranted up to Tcase of 85℃ max. Operating bank interleave read current; All bank interleaving reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), tRC = tRC(IDD), tRRD = tRRD(IDD), tRCD = 1*tCK(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are STABLE during DESELECTs; Data pattern is same as IDD4R; - Refer to the following page for detailed timing conditions mA IDD4W mA IDD4R mA IDD5B mA IDD6 mA IDD7 mA Note: 1. IDD specifications are tested after the device is properly initialized 2. Input slew rate is specified by AC Parametric Test Condition 3. IDD parameters are specified with ODT disabled. 4. Data bus consists of DQ, DM, DQS, DQS, RDQS, RDQS, LDQS, LDQS, UDQS, and UDQS. IDD values must be met with all combinations of EMRS bits 10 and 11. 5. Definitions for IDD LOW is defined as Vin ≤ VILAC (max) HIGH is defined as Vin ≥ VIHAC (min) STABLE is defined as inputs stable at a HIGH or LOW level FLOATING is defined as inputs at VREF = VDDQ/2 SWITCHING is defined as: inputs changing between HIGH and LOW every other clock cycle (once per two clocks) for address and control signals, and inputs changing between HIGH and LOW every other data transfer (once per clock) for DQ signals not including masks or strobes Rev. 0.3 / Oct. 2008 21 1240pin Registered DDR2 SDRAM DIMMs Electrical Characteristics & AC Timings Speed Bins and CL, tRCD, tRP, tRC and tRAS for Corresponding Bin Speed Bin (CL-tRCD-tRP) Parameter CAS Latency tRCD tRP tRC tRAS DDR2-800 (S5) 5-5-5 min 5 12.5 12.5 57.5 45 DDR2-667 (Y5) 5-5-5 min 5 15 15 60 45 DDR2-533 (C4) 4-4-4 min 4 15 15 60 45 Unit ns ns ns ns ns AC Timing Parameters by Speed Grade (DDR2-400 & DDR2-533) DDR2-400 Parameter Data-Out edge to Clock edge Skew DQS-Out edge to Clock edge Skew Clock High Level Width Clock Low Level Width Clock Half Period System Clock Cycle Time DQ and DM input setup time DQ and DM input hold time Control & Address input Pulse Width for each input DQ and DM input pulse width for each input pulse width for each input Data-out high-impedance window from CK, /CK DQS low-impedance time from CK/CK DQ low-impedance time from CK/CK DQS-DQ skew for DQS and associated DQ signals DQ hold skew factor DQ/DQS output hold time from DQS Write command to first DQS latching transition DQS input high pulse width DQS input low pulse width DQS falling edge to CK setup time DQS falling edge hold time from CK Mode register set command cycle time Write preamble DDR2-533 Unit Note Min -500 -500 0.45 0.45 min (tCL, tCH) 3750 100 225 0.6 0.35 tAC min 2*tAC min tHP - tQHS WL - 0.25 0.35 0.35 0.2 0.2 2 0.35 Symbol Min tAC tDQSCK tCH tCL tHP tCK tDS tDH tIPW tDIPW tHZ tLZ(DQS) tLZ(DQ) tDQSQ tQHS tQH tDQSS tDQSH tDQSL tDSS tDSH tMRD tWPRE -600 -500 0.45 0.45 min (tCL, tCH) 5000 150 275 0.6 0.35 tAC min 2*tAC min tHP - tQHS WL - 0.25 0.35 0.35 0.2 0.2 2 0.35 Max 600 500 0.55 0.55 8000 tAC max tAC max tAC max 350 450 WL + 0.25 - Max 500 450 0.55 0.55 8000 tAC max tAC max tAC max 300 400 WL + 0.25 ps ns CK CK ns ps ps ps tCK tCK ps ps ps ps ps ps tCK tCK tCK tCK tCK tCK tCK 1 1 Rev. 0.3 / Oct. 2008 22 1240pin Registered DDR2 SDRAM DIMMs DDR2-400 Parameter Write postamble Address and control input setup time Address and control input hold time Read preamble Read postamble Auto-Refresh to Active/Auto-Refresh command period Row Active to Row Active Delay for 1KB page size Row Active to Row Active Delay for 2KB page size Four Activate Window for 1KB page size Four Activate Window for 2KB page size CAS to CAS command delay Write recovery time Auto Precharge Write Recovery + Precharge Time Write to Read Command Delay Internal read to precharge command delay Exit self refresh to a non-read command Exit self refresh to a read command Exit precharge power down to any non-read command Exit active power down to read command Exit active power down to read command (Slow exit, Lower power) CKE minimum pulse width (high and low pulse width) ODT turn-on delay ODT turn-on ODT turn-on (Power-Down mode) ODT turn-off delay ODT turn-off ODT turn-off (Power-Down mode) ODT to power down entry latency ODT power down exit latency OCD drive mode output delay Minimum time clocks remains ON after CKE asynchronously drops LOW Average periodic Refresh Interval tREFI 3.9 3.9 us 3 DDR2-533 Unit Note Min 0.4 250 375 0.9 0.4 127.5 7.5 10 37.5 50 2 15 tWR + tRP 7.5 7.5 tRFC + 10 200 2 2 6 - AL 3 2 2 tAC (min) tAC(min)+2 2.5 tAC (min) tAC(min)+2 3 8 12 0 tIS + tCK + tIH 12 2 tAC(max)+1 2tCK+tAC(m ax)+1 2.5 tAC (max)+ 0.6 2.5tCK+tAC( max)+1 - Symbol Min tWPST tIS tIH tRPRE tRPST tRFC tRRD tRRD tFAW tFAW tCCD tWR tDAL tWTR tRTP tXSNR tXSRD tXP tXARD tXARDS tCKE tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD tOIT tDelay tREFI 0.4 350 475 0.9 0.4 127.5 7.5 10 37.5 50 2 15 tWR + tRP 10 7.5 tRFC + 10 200 2 2 6 - AL 3 2 tAC (min) tAC(min)+2 2.5 tAC (min) tAC(min)+2 3 8 0 tIS + tCK + tIH 7.8 Max 0.6 1.1 0.6 - Max 0.6 1.1 0.6 tCK ps ps tCK tCK ns ns ns ns ns tCK ns tCK ns ns ns tCK tCK tCK tCK tCK tCK ns ns tCK ns ns tCK tCK ns ns 7.8 us 2 tAC(max)+1 2tCK+tAC(m ax)+1 2.5 tAC (max)+ 0.6 2.5tCK+tAC( max)+1 - Note: 1. For details and notes, please refer to the relevant HYNIX component datasheet H5PS1G[4,8]3EFR. 2. 0°C ≤ TCASE ≤ 85°C 3. 85°C ＜ TCASE ≤ 95°C Rev. 0.3 / Oct. 2008 23 1240pin Registered DDR2 SDRAM DIMMs (DDR2-667 & DDR2-800) Parameter DQ output access time from CK/CK DQS output access time from CK/CK CK high-level width CK low-level width CK half period Clock cycle time, CL=x DQ and DM input setup time (differential strobe) DQ and DM input hold time (differential strobe) Control & Address input pulse width for each input DQ and DM input pulse width for each input Data-out high-impedance time from CK/CK DQS low-impedance time from CK/CK DQ low-impedance time from CK/CK DQS-DQ skew for DQS and associated DQ signals DQ hold skew factor DQ/DQS output hold time from DQS First DQS latching transition to associated clock edge DQS input high pulse width DQS input low pulse width DQS falling edge to CK setup time DQS falling edge hold time from CK Mode register set command cycle time Write preamble Write postamble Auto-Refresh to Active/Auto-Refresh command period Row Active to Row Active Delay for 1KB page size Address and control input setup time Address and control input hold time Read preamble Read postamble Activate to precharge command Active to active command period for 1KB page size products Row Active to Row Active Delay for 2KB page size Four Active Window for 1KB page size products Four Activate Window for 2KB page size CAS to CAS command delay Write recovery time Auto precharge write recovery + precharge time Internal write to read command delay Internal read to precharge command delay Symbol tAC tDQSCK tCH tCL tHP tCK tDS tDH tIPW tDIPW tHZ tLZ(DQS) tLZ(DQ) tDQSQ tQHS tQH tDQSS tDQSH tDQSL tDSS tDSH tMRD tWPRE tWPST tRFC tRRD tIS tIH tRPRE tRPST tRAS tRRD tRRD tFAW tFAW tCCD tWR tDAL tWTR tRTP DDR2-667 min -450 -400 0.45 0.45 min(tCL, tCH) 3000 100 175 0.6 0.35 tAC min 2*tAC min tHP - tQHS - 0.25 0.35 0.35 0.2 0.2 2 0.35 0.4 127.5 7.5 200 275 0.9 0.4 45 7.5 10 37.5 50 2 15 WR+tRP 7.5 7.5 max +450 +400 0.55 0.55 8000 tAC max tAC max tAC max 240 340 + 0.25 0.6 1.1 0.6 70000 min -400 -350 0.45 0.45 min(tCL, tCH) 2500 50 125 0.6 0.35 tAC min 2*tAC min tHP - tQHS - 0.25 0.35 0.35 0.2 0.2 2 0.35 0.4 127.5 7.5 175 250 0.9 0.4 45 7.5 10 35 50 2 15 WR+tRP 7.5 7.5 tAC max tAC max tAC max 200 300 + 0.25 0.6 1.1 0.6 70000 DDR2-800 max +400 +350 0.55 0.55 Unit ps ps tCK tCK ps ps ps ps tCK tCK ps ps ps ps ps ps tCK tCK tCK tCK tCK tCK tCK tCK ns ns ps ps tCK tCK ns ns ns ns ns tCK ns tCK ns ns 1 1 Note Rev. 0.3 / Oct. 2008 24 1240pin Registered DDR2 SDRAM DIMMs Parameter Exit self refresh to a non-read command Exit self refresh to a read command Exit precharge power down to any non-read command Exit active power down to read command Exit active power down to read command (Slow exit, Lower power) CKE minimum pulse width (high and low pulse width) ODT turn-on delay ODT turn-on ODT turn-on (Power-Down mode) ODT turn-off delay ODT turn-off ODT turn-off (Power-Down mode) ODT to power down entry latency ODT power down exit latency OCD drive mode output delay Minimum time clocks remains ON after CKE asynchronously drops LOW Average periodic Refresh Interval Symbol tXSNR tXSRD tXP tXARD tXARDS tCKE tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD tOIT tDelay tREFI tREFI DDR2-667 min tRFC + 10 200 2 2 7 - AL 3 2 tAC (min) tAC(min)+2 2.5 tAC (min) tAC (min) +2 3 8 0 tIS + tCK + tIH 7.8 3.9 12 2 tAC (max) +0.7 2tCK+ tAC(max)+1 2.5 tAC (max)+ 0.6 2.5tCK+ tAC(max)+1 max min DDR2-800 max tRFC + 10 200 2 2 8 - AL 3 2 tAC (min) tAC (min) +2 2.5 tAC (min) tAC (min) +2 3 8 0 tIS + tCK + tIH 7.8 3.9 12 2 tAC (max) +0.7 2tCK+ tAC(max)+1 2.5 tAC (max) +0.6 2.5tCK+ tAC(max)+1 Unit ns tCK tCK tCK tCK tCK tCK ns ns tCK ns ns tCK tCK ns ns us us Note 2 3 Note: 1. For details and notes, please refer to the relevant HYNIX component datasheet H5PS1G[4,8]3EFR. 2. 0°C ≤ TCASE ≤ 85°C 3. 85°C ＜ TCASE ≤ 95°C Rev. 0.3 / Oct. 2008 25 1240pin Registered DDR2 SDRAM DIMMs PACKAGE OUTLINE 128Mx72 (1 rank) - HMP112P7EFR8C Front 2X 3.00MIN Register 4X FULL R 17.80 30.00 4X 4.0 ± 0.1 PLL 2X 2.3 ± 0.1 5.175 10.00 2X Ø 2.50 ± 0.10 2X R1.00 63.0 DETAIL-A 5.0 128.95 133.35 DETAIL-B 55.0 Back Detail of Contacts A 2.50 ± 0.20 0.35 0.05 Detail of Contacts B 2.50 3.0 ± 0.15 Side 2.70max 1.0 0.8 ± 0.05 1.50 ± 0.10 0.3 ± 0.7 5.00 3.80 1.27 ± 0.10 Note) All dimensions are typical unless otherwise stated. Millimeters Inches Rev. 0.3 / Oct. 2008 26 1240pin Registered DDR2 SDRAM DIMMs PACKAGE OUTLINE 256Mx72 (2 rank) - HMP125P7EFR8C Front 2X 3.00MIN Register 4X FULL R 17.80 30.00 10.00 4X 4.0 ± 0.1 PLL 2X 2.3 ± 0.1 5.175 2X Ø 2.50 ± 0.10 2X R1.00 63.0 DETAIL-A 5.0 128.95 133.35 DETAIL-B 55.0 Back Detail of Contacts A 2.50 ± 0.20 0.35 0.05 Detail of Contacts B 2.50 3.0 ± 0.15 Register Side 4.00max 1.0 0.8 ± 0.05 1.50 ± 0.10 0.3 ± 0.7 5.00 3.80 1.27 ± 0.10 Note) All dimensions are typical unless otherwise stated. Millimeters Inches Rev. 0.3 / Oct. 2008 27 1240pin Registered DDR2 SDRAM DIMMs PACKAGE OUTLINE 256Mx72 (1 rank) - HMP125P7EFR4C Front 2X 3.00MIN Register 4X FULL R 17.80 30.00 10.00 4X 4.0 ± 0.1 PLL 2X 2.3 ± 0.1 5.175 2X Ø 2.50 ± 0.10 2X R1.00 63.0 DETAIL-A 5.0 128.95 133.35 DETAIL-B 55.0 Back Detail of Contacts A 2.50 ± 0.20 0.35 0.05 Detail of Contacts B 2.50 3.0 ± 0.15 Register Side 4.00max 1.0 0.8 ± 0.05 1.50 ± 0.10 0.3 ± 0.7 5.00 3.80 1.27 ± 0.10 Note) All dimensions are typical unless otherwise stated. Millimeters Inches Rev. 0.3 / Oct. 2008 28 1240pin Registered DDR2 SDRAM DIMMs PACKAGE OUTLINE 512Mx72 (4 ranks) - HYMP151P7EFR8C Front Register 2X 3.00MIN PLL 4X FULL R 17.80 4X 4.0 ± 0.1 Register 30.00 10.00 2X Ø 2.50 ± 0.10 2X 2.3 ± 0.1 5.175 2X R1.00 63.0 DETAIL-A 5.0 128.95 133.35 DETAIL-B 55.0 Back Register Register Detail of Contacts A 2.50 ± 0.20 0.35 0.05 Detail of Contacts B 2.50 3.0 ± 0.15 Side 4.00max 1.0 0.8 ± 0.05 1.50 ± 0.10 0.3 ± 0.7 3.80 5.00 1.27 ± 0.10 Note) All dimensions are typical unless otherwise stated. Millimeters Inches Rev. 0.3 / Oct. 2008 29 1240pin Registered DDR2 SDRAM DIMMs PACKAGE OUTLINE 512Mx72 (2 ranks) - HYMP151P7EFR4C Front Register 2X 3.00MIN PLL 4X FULL R 17.80 30.00 10.00 2X Ø 2.50 ± 0.10 4X 4.0 ± 0.1 2X 2.3 ± 0.1 5.175 2X R1.00 63.0 DETAIL-A 5.0 128.95 133.35 DETAIL-B 55.0 Back Register Detail of Contacts A 2.50 ± 0.20 0.35 0.05 Detail of Contacts B 2.50 3.0 ± 0.15 Side 4.00max 1.0 0.8 ± 0.05 1.50 ± 0.10 0.3 ± 0.7 3.80 5.00 1.27 ± 0.10 Note) All dimensions are typical unless otherwise stated. Millimeters Inches Rev. 0.3 / Oct. 2008 30 1240pin Registered DDR2 SDRAM DIMMs PACKAGE OUTLINE 1Gx72 (4 ranks) - HMP31GP7EMR4C Front 2X 3.00MIN PLL 4X FULL R 17.80 30.00 10.00 2X Ø 2.50 ± 0.10 4X 4.0 ± 0.1 Register 2X 2.3 ± 0.1 5.175 2X R1.00 63.0 DETAIL-A 5.0 128.95 133.35 DETAIL-B 55.0 Back Register Detail of Contacts A 2.50 ± 0.20 0.35 0.05 Detail of Contacts B 2.50 3.0 ± 0.15 Side 7.55max 1.0 0.8 ± 0.05 1.50 ± 0.10 0.3 ± 0.7 3.80 5.00 1.27 ± 0.10 Note) All dimensions are typical unless otherwise stated. Millimeters Inches Rev. 0.3 / Oct. 2008 31 1240pin Registered DDR2 SDRAM DIMMs REVISION HISTORY Revision 0.1 0.2 0.3 History Initial release Editorial Correction Added 2Rx8, 4Rx8 Date Jul. 2008 Sep. 2008 Oct. 2008 Rev. 0.3 / Oct. 2008 32