ICG2130-EVAL

• • • • • • • Characterized for 100-3000MHz Operation +26 dBm Output IP3 +17 dB Gain at 850 MHz +12 dB Gain at 2000 MHz Internally 50 matched input and output +3V Single Voltage Supply Low Current Consumption: 30mA The ICG series of Gain Blocks are general purpose gain stages consisting of Broadband MMIC amplifiers in a Darlington configuration. The amplifiers housed in a lowcost surface mountable package provide a high output intercept point, high gain and low noise figure and do not require an external bias resistor. The ICG2130 can be used for amplification in IF and RF applications from 100 MHz to 3000 MHz. The amplifier provides a gain of 17dB typically at 850 MHz and has single ended input and output, internally matched to 50 Ohms. The device can be operated with a single +3V supply. The IC is available in industry standard 6L-SOT23 package. • • • • • • • IF or RF Buffer Amplifier Driver/Pre-Driver for CATV/SAT TV Amplifier VCO Buffer Driving Up/Down Converter General Rx/Tx Amplification LNB IF Path ISM Band Transceivers - WLAN - IEEE 802.11, Bluetooth ISO/EPC Compliant UHF RFID Readers Gnd 1 Bias 6 Gnd RFin 2 5 Vcc / RFout Gnd 3 4 ICG2130 Gnd !" Gnd 1 6 Gnd 6L-SOT23 C MI 0 IC 213 G IC Rfin 2 ICG2130 5 Vcc / RFout Gnd 3 4 Gnd Performance tests for ICmic products were performed internally by ICmic and measured using specific systems and/or components. Any difference in circuit implementation, test software, or test equipment may affect actual performance. The information provided herein is believed to be reliable at the time of this printing. ICmic assumes no responsibility for the use of this information and/or the described product(s). Prices and specifications are subject to change without notice. Copyright 2004 IC MICROSYSTEMS SDN. BHD. All worldwide rights reserved Rev. 1.0 28/12/04 ICmic reserves the right to change the specifications without notice. For more information please visit http://www.icmic.com 1 Pin # 1 2 3 4 Symbol Gnd RFin Gnd Gnd Description Ground connection. Keep traces physically short and immediately connect to ground plane. RF input pin. This pin is not externally DC blocked and thus requires an external blocking capacitor suitable for the frequency of operation. The input impedance of this pin is internally matched to 50 using resistive feedback. Same as Pin 1 Same as Pin 1 RF out and bias pin. The input impedance of this pin is internally matched to 50 using resistive feedback. Bias should be supplied to this pin externally. Please note that an RF choke inductor is required but no external bias resistor is needed. A DC blocking capacitor should be used for most applications since DC bias is present on this pin. The supply should be well-bypassed. Same as Pin 1 5 Vcc/RFout 6 Gnd # Symbol VCC TOP TSTG TSOL Parameter Positive Power Supply Operating Temperature Storage Temperature Soldering Temperature Value +4.0 -40 to +85 -65 to +150 300 Unit VDC o o o Part ICG2130 ICG2130-EVAL Description 6L-SOT23, 3V Amplifier Fully Assembled Evaluation Board C C C Parameter VCC TOP Value +3.0 +25 Unit VDC o Note: Stress greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. C Unless otherwise stated, measurements were done on the evaluation board $%& '() *(+ & ,* *, * Appropriate precaution in handling, packaging and testing must be observed Rev. 1.0 28/12/04 ICmic reserves the right to change the specifications without notice. For more information please visit http://www.icmic.com 2 Parameter Supply Voltage Supply Current Test Conditions Min 27 Typ +3.0 30 Max 33 Unit V mA Parameter Overall Frequency Range 100 MHz Performance Gain Noise Figure Output IP3 Output P1dB Input Return Loss Output Return Loss Isolation 850 MHz Performance Gain Noise Figure Output IP3 Output P1dB Input Return Loss Output Return Loss Isolation 2000 MHz Performance Gain Noise Figure Output IP3 Output P1dB Input Return Loss Output Return Loss Isolation 3000 MHz Performance Gain Noise Figure Output IP3 Output P1dB Input Return Loss Output Return Loss Isolation Test Conditions Min DC Typ 850 Max 3000 Unit MHz VCC=+3.0V, TOP = +25 oC 18.8 3.5 25 14.3 16.2 16.7 21.5 dB dB dBm dBm dB dB dB VCC=+3.0V, TOP = +25 oC 18.8 3.4 26 14.8 15.4 27.6 21.3 dB dB dBm dBm dB dB dB VCC=+3.0V, TOP = +25 oC 13.3 3.6 21 11.5 17.2 20.8 20 dB dB dBm dBm dB dB dB VCC=+3.0V, TOP = +25 oC 10.8 3.9 18 8.5 13.4 11.3 19.2 dB dB dBm dBm dB dB dB Rev. 1.0 28/12/04 ICmic reserves the right to change the specifications without notice. For more information please visit http://www.icmic.com 3 Pout VS Pin 20.00 15.00 10.00 5.00 Pout (dBm) 0.00 -5.00 -10.00 -15.00 -20.00 -25.00 -35 -30 -25 -20 -15 -10 Pin (dBm) -5 0 5 10 15 Gain (dB) 850 MHz 2000 MHz 3000 MHz 18.00 16.00 14.00 12.00 10.00 8.00 6.00 4.00 2.00 0.00 -30 -25 -20 -15 Gain VS Pin 850 MHz 2000 MHz 3000 MHz -10 Pin (dBm) -5 0 5 10 ICG2130 S21, Vcc=+3.0V 20.00 ICG2130 S12, Vcc=+3.0V -10.00 16.00 -14.00 S21 (dB) S12 (dB) 12.00 -18.00 8.00 -22.00 4.00 -26.00 0.00 100.00 1100.00 Freq (MHz) 2100.00 3100.00 -30.00 100.00 1100.00 Freq (MHz) 2100.00 3100.00 ICG2130 S11, Vcc=+3.0V ICG2130 S22, Vcc=+3.0V Swp Max: 3 GHz 3000 MHz 100 MHz 100 MHz 3000 MHz Swp Min: 0.1 GHz Rev. 1.0 28/12/04 ICmic reserves the right to change the specifications without notice. For more information please visit http://www.icmic.com 4 ICG2130 S21, Vcc=+3.3V 20.00 16.00 12.00 8.00 4.00 0.00 100.00 -10.00 ICG2130 S12, Vcc=+3.3V -14.00 S 2 1 (d B ) S12 (dB) -18.00 -22.00 -26.00 1100.00 Freq (MHz) 2100.00 3100.00 -30.00 100.00 1100.00 Freq (MHz) 2100.00 3100.00 ICG2130 S11, Vcc=+3.3V ICG2130 S22, Vcc=+3.3V Swp Max: 3 GHz 3000 MHz 100 MHz 100 MHz 3000 MHz Swp Min: 0.1 GHz Rev. 1.0 28/12/04 ICmic reserves the right to change the specifications without notice. For more information please visit http://www.icmic.com 5 VCC 1 GND Bias GND 6 L1 C1 VCC C3 RFin C2 2 RFin RFout 5 RFout 3 GND U1 ICG2130 GND 4 J1 1 +5V GND Bias GND 6 L1 C1 VCC C3 J2 50ΩµStrip C2 2 RFin RFout 5 J3 50ΩµStrip 3 GND U1 ICG2130 GND 4 PCB Top - Component Side PCB SilkScreen Rev. 1.0 28/12/04 ICmic reserves the right to change the specifications without notice. For more information please visit http://www.icmic.com 6 ICG2130-EVAL Component Designator U1 J1 J2, J3 C1 C2, C3 L1 Value Qty 1 1 2 Description ICG2130 Gain Block 2 Pin Header - VCC SMA End Launch Connectors Bypass Capacitor Blocking Capacitors Inductor 4.7 µF 100 pF 220 nH 1 2 1 !" Rev. 1.0 28/12/04 ICmic reserves the right to change the specifications without notice. For more information please visit http://www.icmic.com 7