IC62LV1024ALL-55H

IC62LV1024AL IC62LV1024ALL Document Title 128K x 8 Ultra Low Power and Low VCC SRAM Revision History Revision No 0A History Initial Draft Draft Date Remark September 13,2001 The attached datasheets are provided by ICSI. Integrated Circuit Solution Inc reserve the right to change the specifications and products. ICSI will answer to your questions about device. If you have any questions, please contact the ICSI offices. Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 1 IC62LV1024AL IC62LV1024ALL 128K x 8 LOW POWER and LOW Vcc CMOS STATIC RAM FEATURES • Access times of 45, 55, and 70 ns • Low active power: 60 mW (typical) • Low standby power: 15 µW (typical) CMOS standby • Low data retention voltage: 2V (min.) • Available in Low Power (-L) and Ultra Low Power (-LL) • Output Enable (OE) and two Chip Enable (CE1 and CE2) inputs for ease in applications • TTL compatible inputs and outputs • Single 2.7V to 3.3V power supply DESCRIPTION The ICSI IC62LV1024AL and IC62LV1024ALL are low power and low Vcc,131,072-word by 8-bit CMOS static RAMs. They are fabricated using ICSI's high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields higher performance and low power consumption devices. When CE1 is HIGH or CE2 is LOW (deselected), the device assumes a standby mode at which the power dissipation can be reduced by using CMOS input levels. Easy memory expansion is provided by using two Chip Enable inputs, CE1 and CE2. The active LOW Write Enable (WE) controls both writing and reading of the memory. The IC62LV1024AL and IC62LV1024ALL are available in 32-pin 8*20mm TSOP-1, 8*13.4mm TSOP-1, 450mil SOP and 48-pin 6*8mm TF-BGA. FUNCTIONAL BLOCK DIAGRAM A0-A16 DECODER 512 X 2048 MEMORY ARRAY VCC GND I/O DATA CIRCUIT I/O0-I/O7 COLUMN I/O CE1 CE2 OE WE CONTROL CIRCUIT ICSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which may appear in this publication. © Copyright 2000, Integrated Circuit Solution Inc. 2 Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 IC62LV1024AL IC62LV1024ALL PIN CONFIGURATION 32-Pin SOP NC A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC A15 CE2 WE A13 A8 A9 A11 OE A10 CE1 I/O7 I/O6 I/O5 I/O4 I/O3 PIN CONFIGURATION 32-Pin 8x20mm TSOP-1 and 8x13.4mm TSOP-1 A11 A9 A8 A13 WE CE2 A15 VCC NC A16 A14 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CE1 I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 A3 48-Pin 6x8mm TF-BGA PIN DESCRIPTIONS A0-A16 Address Inputs Chip Enable 1 Input Chip Enable 2 Input Output Enable Input Write Enable Input Input/Output No Connection Power Ground CE1 CE2 OE WE I/O0-I/O7 NC Vcc GND 1 A B C D E F G H A0 I/O5 I/O6 GND Vcc I/O7 I/O8 A9 2 A1 A2 3 CE2 WE NC 4 A3 A4 A5 5 A6 A7 6 A8 I/O1 I/O2 Vcc GND NC OE A10 CE1 A11 NC A16 A12 A15 A13 I/O3 I/O4 A14 OPERATING RANGE Range Commercial Industrial Ambient Temperature 0°C to +70°C –40°C to +85°C VCC 2.7V to 3.3V 2.7V to 3.3V Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 3 IC62LV1024AL IC62LV1024ALL TRUTH TABLE Mode Not Selected (Power-down) Output Disabled Read Write WE X X H H L CE1 H X L L L CE2 X L H H H OE X X H L X I/O Operation High-Z High-Z High-Z DOUT DIN Vcc Current ISB1, ISB2 ISB1, ISB2 ICC ICC ICC ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM VCC TBIAS TSTG PT Parameter Terminal Voltage with Respect to GND Vcc related to GND Temperature Under Bias Storage Temperature Power Dissipation Value –0.5 to +3.6 –0.3 to +3.6 –40 to +85 –65 to +150 0.7 Unit V V °C °C W Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. CAPACITANCE(1,2) Symbol CIN COUT Parameter Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Max. 6 8 Unit pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz, Vcc = 3.0V. DC ELECTRICAL CHARACTERISTICS (Over Operating Range) Symbol VOH VOL VIH VIL ILI ILO Parameter Output HIGH Voltage Output LOW Voltage Input HIGH Voltage Input LOW Voltage(1) Input Leakage Output Leakage Test Conditions VCC = Min., IOH = –1.0 mA VCC = Min., IOL = 2.1 mA Min. 2.2 — 2.2 –0.3 –1 –1 Max. — 0.4 VCC + 0.3 0.4 1 1 Unit V V V V µA µA GND ≤ VIN ≤ VCC GND ≤ VOUT ≤ VCC Notes: 1. VIL = –3.0V for pulse width less than 10 ns. 4 Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 IC62LV1024AL IC62LV1024ALL IC62LV1024AL POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter ICC ISB1 Vcc Dynamic Operating Supply Current TTL Standby Current (TTL Inputs) CMOS Standby Current (CMOS Inputs) Test Conditions VCC = Max., CE = VIL IOUT = 0 mA, f = fMAX Com. Ind. -45L ns Min. Max. — — — — — — 40 45 0.8 1 50 75 -55L ns Min. Max. — — — — — — 35 40 0.8 1 50 75 -70L ns Min. Max. — — — — — — 30 35 0.8 1 50 75 Unit mA mA VCC = Max., Com. VIN = VIH or VIL, CE1 ≥ VIH Ind. or CE2 ≤ VIL, f = 0 VCC = Max., f = 0 Com. CE1 ≥ VCC – 0.2V, Ind. CE2 ≤ 0.2V, or VIN ≥ VCC – 0.2V, VIN ≤ 0.2V ISB2 µA Note: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. IC62LV1024ALL POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter ICC ISB1 Vcc Dynamic Operating Supply Current TTL Standby Current (TTL Inputs) CMOS Standby Current (CMOS Inputs) Test Conditions VCC = Max., CE = VIL IOUT = 0 mA, f = fMAX Com. Ind. -45LL ns Min. Max. — — — — — — 40 45 0.8 1 5 10 -55LL ns Min. Max. — — — — — — 35 40 0.8 1 5 10 -70LL ns Min. Max. — — — — — — 30 35 0.8 1 5 10 Unit mA mA VCC = Max., Com. VIN = VIH or VIL, CE1 ≥ VIH Ind. or CE2 ≤ VIL, f = 0 VCC = Max., f = 0 Com. CE1 ≥ VCC – 0.2V, Ind. CE2 ≤ 0.2V, or VIN ≥ VCC – 0.2V, VIN ≤ 0.2V ISB2 µA Note: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 5 IC62LV1024AL IC62LV1024ALL READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) -45 Symbol Parameter Read Cycle Time Address Access Time Output Hold Time CE1 Access Time CE2 Access Time OE Access Time (2) (2) -55 Min. 55 — 10 — — — 5 0 7 7 0 Max. — 55 — 55 55 25 — 20 — — 20 Min. 70 — 10 — — — 5 0 10 10 0 -70 Max. — 70 — 70 70 35 — 25 — — 25 Unit ns ns ns ns ns ns ns ns ns ns ns Min. 45 — 10 — — — 0 0 5 5 0 Max. — 45 — 45 45 20 — 15 — — 15 tRC tAA tOHA tACE1 tACE2 tDOE tLZOE tHZOE OE to Low-Z Output OE to High-Z Output CE2 to Low-Z Output CE1 or CE2 to High-Z Output tLZCE1(2) CE1 to Low-Z Output tLZCE2 tHZCE (2) (2) Notes: 1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0.4V to 2.2V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load Unit 0.4V to 2.2V 5 ns 1.5V See Figures 1 AC TEST LOADS 1 TTL OUTPUT 100 pF Including jig and scope Figure 1. 6 1 TTL OUTPUT 5 pF Including jig and scope Figure 2. Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 IC62LV1024AL IC62LV1024ALL AC WAVEFORMS READ CYCLE NO. 1(1,2) tRC ADDRESS tAA tOHA tOHA DATA VALID DOUT READ CYCLE NO. 2(1,3) tRC ADDRESS tAA tOHA OE tDOE tHZOE CE1 tACE1/tACE2 tLZOE CE2 tLZCE1/ tLZCE2 HIGH-Z tHZCE DATA VALID DOUT Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE1 = VIL, CE2 = VIH. 3. Address is valid prior to or coincident with CE1 LOW and CE2 HIGH transitions. Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 7 IC62LV1024AL IC62LV1024ALL WRITE CYCLE SWITCHING CHARACTERISTICS(1,3) (Over Operating Range, Standard and Low Power) -45 Symbol Parameter Write Cycle Time CE1 to Write End CE2 to Write End Address Setup Time to Write End Address Hold from Write End Address Setup Time (4) -55 Min. 55 50 50 50 0 0 40 25 0 — 5 Max. — — — — — — — — — 20 — Min. 70 60 60 60 0 0 55 30 0 0 5 -70 Max. — — — — — — — — — 25 — Unit ns ns ns ns ns ns ns ns ns ns ns Min. 45 35 35 35 0 0 35 25 0 — 5 Max. — — — — — — — — — 15 — tWC tSCE1 tSCE2 tAW tHA tSA tPWE tSD tHD tHZWE tLZWE (2) (2) WE Pulse Width Data Setup to Write End Data Hold from Write End WE LOW to High-Z Output WE HIGH to Low-Z Output Notes: 1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0.4V to 2.2V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE1 LOW, CE2 HIGH and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. 4. Tested with OE HIGH. AC WAVEFORMS WRITE CYCLE NO. 1 (WE Controlled)(1,2) tWC ADDRESS tSCE1 tHA CE1 tSCE2 CE2 tAW tPWE(4) tSA tHZWE HIGH-Z WE tLZWE DOUT DATA UNDEFINED tSD tHD DIN DATA-IN VALID 8 Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 IC62LV1024AL IC62LV1024ALL WRITE CYCLE NO. 2 (CE1, CE2 Controlled)(1,2) tWC ADDRESS tSA tSCE1 tHA CE1 tSCE2 CE2 tAW tPWE(4) WE tHZWE tLZWE HIGH-Z DOUT DATA UNDEFINED tSD tHD DIN DATA-IN VALID Notes: 1. The internal write time is defined by the overlap of CE1 LOW, CE2 HIGH and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. 2. I/O will assume the High-Z state if OE = VIH. DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter Vcc for Data Retention Data Retention Current Test Condition See Data Retention Waveform Vcc = 2.0V, CE1 ≥ Vcc – 0.2V Com. (-L) Com. (-LL) Ind. (-L) Ind. (-LL) Min. 2.0 — — — — 0 Max. 3.3 30 5 50 10 — — Unit V µA µA µA µA ns ns VDR IDR tSDR tRDR Data Retention Setup Time Recovery Time See Data Retention Waveform See Data Retention Waveform tRC DATA RETENTION WAVEFORM (CE1 Controlled) tSDR VCC Data Retention Mode tRDR 3.0V 2.2V VDR CE1 ≥ VCC - 0.2V CE1 GND Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 9 IC62LV1024AL IC62LV1024ALL DATA RETENTION WAVEFORM (CE2 Controlled) Data Retention Mode VCC tSDR tRDR 3.0V CE2 2.2V VDR 0.4V GND CE2 ≤ 0.2V IC62LV1024AL ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) Order Part No. 45 IC62LV1024AL-45Q IC62LV1024AL-45T IC62LV1024AL-45H IC62LV1024AL-45B IC62LV1024AL-55Q IC62LV1024AL-55T IC62LV1024AL-55H IC62LV1024AL-55B IC62LV1024AL-70Q IC62LV1024AL-70T IC62LV1024AL-70H IC62LV1024AL-70B Package 450milSOP 8*20mmTSOP-1 8*13.4mmTSOP-1 6*8mmTF-BGA 450milSOP 8*20mmTSOP-1 8*13.4mmTSOP-1 6*8mmTF-BGA 450milSOP 8*20mmTSOP-1 8*13.4mmTSOP-1 6*8mmTF-BGA IC62LV1024AL ORDERING INFORMATION Industrial Range: –40°C to +85°C Speed (ns) Order Part No. 45 IC62LV1024AL-45QI IC62LV1024AL-45TI IC62LV1024AL-45HI IC62LV1024AL-45BI IC62LV1024AL-55QI IC62LV1024AL-55TI IC62LV1024AL-55HI IC62LV1024AL-55BI IC62LV1024AL-70QI IC62LV1024AL-70TI IC62LV1024AL-70HI IC62LV1024AL-70BI Package 450milSOP 8*20mmTSOP-1 8*13.4mmTSOP-1 6*8mmTF-BGA 450milSOP 8*20mmTSOP-1 8*13.4mmTSOP-1 6*8mmTF-BGA 450milSOP 8*20mmTSOP-1 8*13.4mmTSOP-1 6*8mmTF-BGA 55 55 70 70 10 Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 IC62LV1024AL IC62LV1024ALL IC62LV1024ALL ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) Order Part No. 45 IC62LV1024ALL-45Q IC62LV1024ALL-45T IC62LV1024ALL-45H IC62LV1024ALL-45B IC62LV1024ALL-55Q IC62LV1024ALL-55T IC62LV1024ALL-55H IC62LV1024ALL-55B IC62LV1024ALL-70Q IC62LV1024ALL-70T IC62LV1024ALL-70H IC62LV1024ALL-70B Package 450mil SOP 8*20mmT SOP-1 8*13.4mmT SOP-1 6*8mmTF- BGA 450mil SOP 8*20mmT SOP-1 8*13.4mmT SOP-1 6*8mmTF- BGA 450mil SOP 8*20mmT SOP-1 8*13.4mmT SOP-1 6*8mmTF- BGA IC62LV1024ALL ORDERING INFORMATION Industrial Range: –40°C to +85°C Speed (ns) Order Part No. 45 IC62LV1024ALL-45QI IC62LV1024ALL-45TI IC62LV1024ALL-45HI IC62LV1024ALL-45BI IC62LV1024ALL-55QI IC62LV1024ALL-55TI IC62LV1024ALL-55HI IC62LV1024ALL-55BI IC62LV1024ALL-70QI IC62LV1024ALL-70TI IC62LV1024ALL-70HI IC62LV1024ALL-70BI Package 450mil SOP 8*20mmT SOP-1 8*13.4mmT SOP-1 6*8mmTF- BGA 450mil SOP 8*20mmT SOP-1 8*13.4mmT SOP-1 6*8mmTF- BGA 450mil SOP 8*20mmT SOP-1 8*13.4mmT SOP-1 6*8mmTF- BGA 55 55 70 70 Integrated Circuit Solution Inc. HEADQUARTER: NO.2, TECHNOLOGY RD. V, SCIENCE-BASED INDUSTRIAL PARK, HSIN-CHU, TAIWAN, R.O.C. TEL: 886-3-5780333 Fax: 886-3-5783000 BRANCH OFFICE: 7F, NO. 106, SEC. 1, HSIN-TAI 5TH ROAD, HSICHIH TAIPEI COUNTY, TAIWAN, R.O.C. TEL: 886-2-26962140 FAX: 886-2-26962252 http://www.icsi.com.tw Integrated Circuit Solution Inc. LPSR017-0A 09/13/2001 11