AV9172

Integrated Circuit Systems, Inc. AV9172 Low Skew Output Buffer General Description The AV9172 is designed to generate low skew clocks for clock distribution in high-performance PCs and workstations. It uses phase-locked loop technology to align the phase and frequency of the output clocks with an input reference clock. Because the input to output skew is guaranteed to ±500ps, the part acts as a “zero delay” buffer. The AV9172 has six configurable outputs. The AV9172-01 version has one output that runs at the same phase and frequency as the reference clock. A second output runs at the same frequency as the reference, but can either be in phase or 180° out of phase from the input clock. Two outputs are provided that are at twice the reference frequency and in phase with the reference clock. The final outputs can be programmed to be replicas of the 2x clocks or non-overlapping two phase clocks at twice the reference frequency. The AV9172-01 and AV9172-03 operates with input clocks from 10 MHz to 50 MHz while producing outputs from 10 MHz to 100 MHz. The AV9172-07 operates with input clocks from 20 to 100 MHz. The use of a phase-locked loop (PLL) allows the output clocks to run at multiples of the input clock. This permits routing of a lower speed clock and local generation of a required high speed clock. Synchronization of the phase relationship between the input clock and the output clocks is accomplished when one output clock is connected to the input pin FBIN. The PLL circuitry matches rising edges of the input clock and output clocks. Features AV9172-07 input is 66 MHz with 66 and 33 MHz output buffers • AV9172-01 is pin compatible with Gazelle GA1210E • ±250ps skew (max) between outputs • ±500ps skew (max) between input and outputs • Input frequency range from 10 MHz to 50 MHz (-01, -03) and from 20 MHz to 100 MHz (-07) • Output frequency range from 10 MHz to 100 MHz (-01, -03, -07) • Special mode for two-phase clock generation • Inputs and outputs are fully TTL-compatible • CMOS process results in low power supply current • High drive, 25mA outputs • Low cost • 16-pin SOIC (150-mil) or 16-pin PDIP package The AV9172 is fabricated using CMOS technology which results in much lower power consumption and cost compared with the gallium arsenide-based GA1210E. The typical operating current for the AV9172 is 50mA versus 120mA for the GA1210E. ICS offers several versions of the AV9172. The different devices are shown below: PART AV9172-01 AV9172-03 AV9172-07 DESCRIPTION Second source of GA1210E Clock doubler and buffer Clock buffer for 66 MHz input • Block Diagram AV9172RevB060297P ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate. AV9172 Pin Configuration Functionality Table for AV9172-01 CLKIN input frequency range 10 to 50 MHz. EN2 0 0 1 1 INV# 0 1 0 1 Q0 1X 1X 1X 1X Q1 1X# 1X 1X# 1X Q2 2X 2X 2X 2X Q3 2X 2X 2X 2X Q4 2X 2X ∅1 ∅1 Q5 2X 2X ∅2 ∅2 16-Pin SOIC or 16-Pin PDIP Notes: 1. 1X designates that the output is a replica of CLKIN. 2. 2X designates that the output is twice the frequency of CLKIN, and in phase. 3. 1X# means that the output is at the same frequency and 180°C out of phase (inverted) from CLKIN. 4. Ø1 will produce a ¼ duty cycle clock of CLKIN. 5. Ø2 will produce a ¼ duty cycle clock delayed 180° from CLKIN. Pin Description for AV9172-01 PIN NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PIN NAME GND GND INV# EN FBIN CLKIN VDD VDD GND Q0 Q1 Q2 Q3 Q4 Q5 VDD TYPE Input Input Input Input Output Output Output Output Output Output DESCRIPTION GROUND. GROUND. INV# Inverts Q1 when low. (-01 [divisor select -03, -07]) EN converts Q4 and Q5 to phase clocks when high. FEEDBACK INPUT from output Q0. INPUT for reference clock. Power supply (+5V). Power supply (+5V). GROUND. Q0 phase and frequency same as input (1X). Feed back to pin 5. Q1 Q2 Q3 Q4 Q5 is a 1x clock in phase or 180° out of phase with input. twice the frequency of Q0 (2x). twice the frequency of Q0 (2x). is either a 2X clock or a two-phase clock - see configuration table. is either a 2X clock or a two-phase clock - see configuration table. Power supply (+5V). 2 AV9172 Timing Diagrams for AV9172-01 3 AV9172 Pin Configuration Functionality Table for AV9172-03 CLKIN Input Frequency=X, input range is 10 to 50 MHz. EN2 0 1 0 1 INV# 0 0 1 1 Q0 2X 2X 2X 2X Q1 2X 2X 2X 2X Q2 2X 2X 2X 2X Q3 2X 2X 1X 1X Q4 2X 2X 1X 1X Q5 2X 1X 2X 1X Example Table for AV9172-03 16-Pin SOIC or 16-Pin PDIP (33 MHz input, all frequencies in MHz.) EN2 0 1 0 1 INV# 0 0 1 1 Q0 66 66 66 66 Q1 66 66 66 66 Q2 66 66 66 66 Q3 66 66 33 33 Q4 66 66 33 33 Q5 66 33 66 33 Timing Diagram for AV9172-03 Note: The phase alignment between the 1X clock outputs and reference clocks input will be either at a 0 or 180 degrees offset if the 2X clock is used as the feedback signal (connected to the FBIN pin). Which relationship occurs is totally random and has the potential to change any time the device has its VDD supply cycled off or the devices input clock removed. 4 AV9172 Pin Configuration Functionality Table for AV9172-07 CLKIN Input Frequency=X, input range is 20 to 100 MHz. EN2 0 1 0 1 INV# 0 0 1 1 Q0 1X 1X 1X 1X Q1 1X 1X 1X 1X Q2 1X 1X 1X 1X Q3 1X 1X 0.5X 0.5X Q4 1X 1X 0.5X 0.5X Q5 1X 0.5X 1X 0.5X Example Table for AV9172-07 (66 MHz input, all frequencies in MHz.) 16-Pin SOIC or 16-Pin PDIP EN2 0 1 0 1 INV# 0 0 1 1 Q0 66 66 66 66 Q1 66 66 66 66 Q2 66 66 66 66 Q3 66 66 33 33 Q4 66 66 33 33 Q5 66 33 66 33 Timing Diagram for AV9172-07 Absolute Maximum Ratings VDD referenced to GND . . . . . . . . . . . . . . . . . . . . . . 7V Operating temperature under bias. . . . . . . . . . . . . . . . 0°C to +70°C Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C Voltage on I/O pins referenced to GND. . . . . . . . . . . GND -0.5V to VDD +0.5V Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 Watts Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. 5 AV9172 Electrical Characteristics VDD =+5V±5%, TA =0°C to 70°C unless otherwise stated DC Characteristics PARAMETER Input Low Voltage Input High Voltage Input Low Current Input High Current Output Low Voltage Output High Voltage Supply Current Input Clock Rise Time Input Clock Fall Time Output Rise time, 0.8 to 2.0V Rise time, 20% to 80% V DD Output Fall time, 2.0 to 0.8V Fall time, 80% to 20% V DD Output Duty cycle Jitter, 1 sigma Jitter, absolute Input Frequency (-01,-03) Input Frequency (-07) Output Frequency (-01,-03, -07) FBIN to IN skew FBIN to IN skew Skew between any 2 outputs at same frequency Skew between any 2 outputs at different frequencies SYMBOL VIL VIH IIL IIH VOL* VOH* IDD ICLKr * ICLKf * tr* tr* tf* tf* dt * T1s* Tabs* fi* fi* fo * tskew1* tskew1* tskew2* TEST CONDITIONS VDD=5V VDD=5V VIN=0V VIN=V IOL=25mA IOH=-25mA Unloaded, 50 MHz outputs AC Characteristics MIN 2.0 -5 -5 2.4 45 TYP 0.5 35 0.7 1.2 0.7 1.2 49/51 60 ae200 MAX 0.8 5 5 0.8 60 10 10 1 2 1 2 55 UNITS V V µA µA V V mA ns ns ns ns ns ns % ps ps MHz MHz MHz ps ps ps ps 15pF load 15pF 15pF 15pF 15pF load load load load 10 20 Note 1 Note 2, 4. Input rise time < 3ns Note 2, 4. Input rise time < 10ns Note 2, 4 Note 2, 4 10 -500 1000 -250 -300 -500 ±50 50 100 100 500 1000 250 500 *Parameter guaranteed by design and characterization. Not 100% tested in production. Notes: 1. Output frequency includes both the Fast Clock (2X or 1X) and the Slow Clock (1X or 0.5X) extremes. 2. All skew specifications are measured with a 50W transmission line, load terminated with 50W to 1.4V. 3. Duty cycle measured at 1.4V. 4. Skew measured at 1.4V on rising edges. Loading must be equal on outputs. 6 AV9172 Typical Performance Characteristics 7 AV9172 16-Pin PDIP Package 16-Pin SOIC Package Ordering Information Part Number AV9172-xxCC16 AV9172-xxCN16 AV9172-xxCW16 AV9172-xxCS16 Example: Part Marking AV9172-XX AV9172-XX AV9172-XX AV9172-XX Temperature 0°C to 70°C 0°C to 70°C 0°C to 70°C 0°C to 70°C Package Type 16 Lead CERDIP 16 Lead Plastic DIP (300 mil) 16 Lead SOIC (300 mil) 16 Lead SOIC (150 mil) ICS XXXX-PPP M X#W Lead Count & Package Width Lead Count=1, 2 or 3 digits W=.3” SOIC or .6” DIP; None=Standard Width Package Type C=CERDIP W=SOIC (300 mil) N=DIP (Plastic#) S=SOIC (150 mil) Pattern Number (2 or 3 digit number for parts with ROM code patterns) Device Type (consists of 3 or 4 digit numbers) Prefix ICS, AV=Standard Device 8 ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.