8344AYI-01LF

Low Skew, 1-to-24 Differential-to-LVCMOS/LVTTL Fanout Buffer General Description The ICS8344I-01 is a low voltage, low skew fanout buffer. The ICS8344I-01 has two selectable clock inputs. The CLKx, nCLKx pairs can accept most standard differential input levels. The ICS8344I-01 is designed to translate any differential signal level to LVCMOS/LVTTL levels. The low impedance LVCMOS/LVTTL outputs are designed to drive 50Ω series or parallel terminated transmission lines. The effective fanout can be increased to 48 by utilizing the ability of the outputs to drive two series terminated lines. Redundant clock applications can make use of the dual clock inputs which also facilitate board level testing. The clock enable is internally synchronized to eliminate runt pulses on the outputs during asynchronous assertion/deassertion of the clock enable pin. The outputs are driven low when disabled. The ICS8344I-01 is characterized at full 3.3V, full 2.5V and mixed 3.3V input and 2.5V output operating supply modes. Guaranteed output and part-to-part skew characteristics make the ICS8344I-01 ideal for those clock distribution applications demanding well defined performance and repeatability. ICS8344I-01 DATA SHEET Features • • • • • • • • • • • • Twenty-four LVCMOS/LVTTL outputs, 7Ω typical output impedance Two selectable differential CLKx, nCLKx inputs CLK0, nCLK0 and CLK1, nCLK1 pairs can accept the following input levels: LVDS, LVPECL, LVHSTL, HCSL Maximum output frequency: 100MHz Translates any single ended input signal to LVCMOS/LVTTL with resistor bias on nCLK input Synchronous clock enable Additive phase jitter, RMS: 0.21ps (typical) Output skew: 200ps (maximum) Part-to-part skew: 900ps (maximum) Bank skew: 180ps (maximum) Propagation delay: 5ns (maximum) Output supply modes: Core/Output 3.3V/3.3V 2.5V/2.5V 3.3V/2.5V -40°C to 70°C ambient operating temperature Available in lead-free (RoHS 6) package • • Block Diagram CLK_SEL Pulldown CLK0 Pulldown nCLK0 Pullup CLK1 Pulldown nCLK1 Pullup Pin Assignment Q15 Q14 GND VDDO Q13 Q12 Q11 Q10 GND VDDO Q9 Q8 0 1 8 Q[0:7] 8 Q[8:15] Q16 Q17 VDDO GND Q18 Q19 Q20 Q21 VDDO GND Q22 Q23 8 Q[16:23] LE CLK_EN Pullup 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 5 6 31 7 30 8 29 9 28 10 27 11 26 12 25 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 CLK_SEL GND VDD nCLK1 CLK1 GND VDD nCLK0 CLK0 CLK_EN OE nc Q7 Q6 VDDO GND Q5 Q4 Q3 Q2 VDDO GND Q1 Q0 Q nD OE Pullup ICS8344I-01 48-Lead LQFP 7mm x 7mm x 1.4mm package body Y Package Top View ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 1 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Table 1. Pin Descriptions Number 1, 2, 5, 6, 7, 8, 11, 12 3, 9, 28, 34, 39, 45 4, 10, 14, 18, 27, 33, 40, 46 13 15, 19 16 17 20 21 22 23 24 25, 26, 29, 30, 31, 32, 35, 36 37, 38, 41, 42, 43, 44, 47, 48 Name Q16, Q17, Q18, Q19, Q20, Q21, Q22, Q23 VDDO GND Output Type Description Single-ended clock outputs. 7Ω typical output Impedance. LVCMOS/LVTTL interface levels. Output supply pins. Power Power Power supply ground. Clock select input. When HIGH, selects CLK1, nCLK inputs, When LOW, selects CLK0, nCLK0 inputs. LVCMOS / LVTTL interface levels. Power supply pins. Pullup Pulldown Pullup Pulldown Pullup Pullup Inverting differential clock input. Non-inverting differential clock input. Inverting differential clock input. Non-inverting differential clock input. Synchronizing control for enabling and disabling clock outputs. LVCMOS / LVTTL interface levels. Output enable. Controls enabling and disabling of outputs Q[0:23]. LVCMOS / LVTTL interface levels. No connect. Single-ended clock outputs. 7Ω typical output Impedance. LVCMOS/LVTTL interface levels. Single-ended clock outputs. 7Ω typical output Impedance. LVCMOS/LVTTL interface levels. CLK_SEL VDD nCLK1 CLK1 nCLK0 CLK0 CLK_EN OE nc Q0, Q1, Q2, Q3, Q4, Q5, Q6, Q7 Q8, Q9, Q10, Q11, Q12, Q13, Q14, Q15 Input Power Input Input Input Input Input Input Unused Output Pulldown Output NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. Table 2. Pin Characteristics Symbol CIN CPD RPULLUP RPULLDOWN ROUT Parameter Input Capacitance Power Dissipation Capacitance (per output) Input Pullup Resistor Input Pulldown Resistor Output Impedance VDDO = 3.3V±5% or 2.5V±5% VDD = VDDO = 3.465V VDD = VDDO = 2.625V Test Conditions Minimum Typical 4 23 16 51 51 7 Maximum Units pF pF pF kΩ kΩ Ω ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 2 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Function Tables Table 3A. Output Enable Function Table Control Input OE 0 1 1 CLK_EN X 0 1 Outputs Q[0:23] High-Impedance Disabled in Logic LOW state; NOTE 1 Enabled; NOTE 1 NOTE 1: The clock enable and disable function is synchronous to the falling edge of the selected reference clock. Table 3A. Clock Select Function Table Control Input CLK_SEL 0 1 CLK0, nCLK0 Selected De-selected Clock CLK1, nCLK1 De-selected Selected Table 3C. Clock Input Function Table Inputs OE 1 (default) 1 1 1 1 1 CLK0, CLK1 0 (default) 1 0 1 Biased; NOTE 1 Biased; NOTE 1 nCLK0, nCLK1 1 (default) 0 Biased; NOTE 1 Biased; NOTE 1 0 1 Outputs Q[0:23] LOW HIGH LOW HIGH HIGH LOW Input to Output Mode Differential to Single-Ended Differential to Single-Ended Single-Ended to Single-Ended Single-Ended to Single-Ended Single-Ended to Single-Ended Single-Ended to Single-Ended Polarity Non-Inverting Non-Inverting Non-Inverting Non-Inverting Inverting Inverting NOTE 1: Please refer to the Application Information Section, Wiring the Differential Input to Accept Single-ended Levels. ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 3 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Absolute Maximum Ratings NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Item Supply Voltage, VDD Inputs, VI Outputs, VO Package Thermal Impedance, θJA Storage Temperature, TSTG Rating 4.6V -0.5V to VDD + 0.5V -0.5V to VDDO + 0.5V 53.9°C/W (0 mps) -65°C to 150°C DC Electrical Characteristics Table 4A. Power Supply DC Characteristics, VDD = VDDO = 3.3V ± 5%, or VDD = VDDO = 2.5V ± 5%, or VDD = 3.3V ± 5%, VDDO = 2.5V ± 5%, TA = -40°C to 70°C Symbol VDD Parameter Power Supply Voltage 2.375 3.135 VDDO IDD Output Supply Voltage 2.375 Power Supply Current 2.5 2.625 95 V mA 2.5 3.3 2.625 3.465 V V Test Conditions Minimum 3.135 Typical 3.3 Maximum 3.465 Units V Table 4B. LVCMOS/LVTTL DC Characteristics, TA = -40°C to 70°C Symbol VIH Parameter Input High Voltage Test Conditions VDD = 3.465V VDD = 2.625V Input Low Voltage Input High Current Input Low Current OE, CLK_EN CLK_SEL OE, CLK_EN CLK_SEL VDD = 3.465V VDD = 2.625V VDD = VIN = 3.465V or 2.625V VDD = VIN = 3.465V or 2.625V VDD = 3.465V or 2.625V, VIN = 0V VDD = 3.465V or 2.625V, VIN = 0V VDDO = 3.135V, IOH = -36mA VDDO = 2.375V, IOH = -27mA Output Low Voltage VDDO = 3.135V, IOL = 36mA VDDO = 2.375V, IOL = 27mA -150 -5 2.7 1.9 0.5 0.5 Minimum 2 2 -0.3 -0.3 Typical Maximum 3.8 2.9 0.8 0.8 5 150 Units V V V V µA µA µA µA V V V V VIL IIH IIL VOH Output High Voltage VOL ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 4 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Table 4C. Differential DC Characteristics, VDD = VDDO = 3.3V ± 5%, or VDD = VDDO = 2.5V ± 5%, or VDD = 3.3V ± 5%, VDDO = 2.5V ± 5%, TA = -40°C to 70°C Symbol IIH Parameter Input High Current Input Low Current nCLK0, nCLK1 CLK0, CLK1 nCLK0, nCLK1 CLK0, CLK1 Test Conditions VDD = VIN = 3.465V or 2.625V VDD = VIN = 3.465V or 2.625V VDD = 3.465V or 2.625V, VIN = 0V VDD = 3.465V or 2.625V, VIN = 0V -150 -5 0.3 0.9 1.3 2.0 Minimum Typical Maximum 5 150 Units µA µA µA µA V V IIL VPP VCMR Peak-to-Peak Voltage; NOTE 1 Common Mode Input Voltage; NOTE 1, 2 NOTE 1: VIL should not be less than -0.3V. NOTE 2: Common mode input voltage is defined as VIH. AC Electrical Characteristics Table 5. AC Characteristics, VDD = VDDO = 3.3V ± 5%, or VDD = VDDO = 2.5V ± 5%, or VDD = 3.3V ± 5%, VDDO = 2.5V ± 5%, TA = -40°C to 70°C Symbol fOUT tPD tjit Parameter Output Frequency Propagation Delay; NOTE 1 Buffer Additive Phase Jitter, RMS; refer to Additive Phase Jitter Section Q[0:7] tsk(b) tsk(o) tsk(pp) tR / tF tEN tDIS odc Bank Skew; NOTE 2, 6 Q[8:15] Q[16:23] Output Skew; NOTE 3, 6 Part-to-Part Skew; NOTE 4, 6 Output Rise/Fall Time; NOTE 5 Output Enable Time; NOTE 5 Output Disable Time; NOTE 5 Output Duty Cycle Measured on the rising edge of VDDO/2 Measured on the rising edge of VDDO/2 30% to 70% f = 10MHz f = 10MHz f ≤ 100MHz 45 200 Measured on the rising edge of VDDO/2 f ≤ 100MHz 100MHz, Integration Range: 12kHz – 20MHz 2.5 0.21 155 180 140 200 900 800 5 4 55 Test Conditions Minimum Typical Maximum 100 5 Units MHz ns ps ps ps ps ps ps ps ns ns % NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device is mounted in a test socket with maintained transverse airflow greater than 500 lfpm. The device will meet specifications after thermal equilibrium has been reached under these conditions. NOTE: All parameters measured at ≤100MHz and VPP_typ unless noted otherwise. NOTE 1: Measured from the differential input crossing point to VDDO/2. NOTE 2: Defined as skew within a bank of outputs at the same voltages and with equal load conditions. NOTE 3: Defined as skew across banks of outputs at the same supply voltages and with equal load conditions. NOTE 4: Defined as between outputs at the same supply voltages and with equal load conditions. Measured at VDDO/2. NOTE 5: These parameters are guaranteed by characterization. Not tested in production. NOTE 6: This parameter is defined in accordance with JEDEC Standard 65. ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 5 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Additive Phase Jitter The spectral purity in a band at a specific offset from the fundamental compared to the power of the fundamental is called the dBc Phase Noise. This value is normally expressed using a Phase noise plot and is most often the specified plot in many applications. Phase noise is defined as the ratio of the noise power present in a 1Hz band at a specified offset from the fundamental frequency to the power value of the fundamental. This ratio is expressed in decibels (dBm) or a ratio of the power in the 1Hz band to the power in the fundamental. When the required offset is specified, the phase noise is called a dBc value, which simply means dBm at a specified offset from the fundamental. By investigating jitter in the frequency domain, we get a better understanding of its effects on the desired application over the entire time record of the signal. It is mathematically possible to calculate an expected bit error rate given a phase noise plot. SSB Phase Noise dBc/Hz Offset from Carrier Frequency (Hz) As with most timing specifications, phase noise measurements has issues relating to the limitations of the equipment. Often the noise floor of the equipment is higher than the noise floor of the device. This is illustrated above. The device meets the noise floor of what is shown, but can actually be lower. The phase noise is dependent on the input source and measurement equipment. ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 6 The source generator used is, "Agilent E5052A Signal Source Analyzer". ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Parameter Measurement Information 1.65V±5% 1.25V±5% VDD, VDDO SCOPE Qx VDD, VDDO SCOPE Qx GND GND -1.65V±5% -1.25V±5% 3.3V Output Load AC Test Circuit 2.5V Output Load AC Test Circuit 2.05V±5% 1.25V±5% VDD VDD VDDO SCOPE nCLK[0:1] Qx CLK[0:1] V PP Cross Points V CMR LVCMOS GND VDDO 2 GND -1.25V±5% 3.3V Core/2.5V Output Load AC Test Circuit Differential Input Level Part 1 V Qx DDO V Qx DDO 2 2 Part 2 V Qy DDO V Qy DDO 2 t sk(o) 2 t sk(pp) Output Skew Part-to-Part Skew ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 7 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Parameter Measurement Information, continued nCLK0, nCLK1 CLK0, CLK1 70% 30% tR 70% 30% tF Q[0:23] VDDO 2 t Q[0:23] PD Propagation Delay Output Rise/Fall Time V Q[0:23] DDO 2 t PW t PERIOD odc = t PW t PERIOD x 100% Output Duty Cycle/Pulse Width/Period ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 8 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Application Information Recommendations for Unused Input and Output Pins Inputs: CLK/nCLK Inputs For applications not requiring the use of the differential input, both CLKx and nCLKx can be left floating. Though not required, but for additional protection, a 1kΩ resistor can be tied from CLKx to ground. Outputs: LVCMOS Outputs All unused LVCMOS outputs can be left floating. There should be no trace attached. LVCMOS Control Pins All control pins have internal pullups or pulldowns; additional resistance is not required but can be added for additional protection. A 1kΩ resistor can be used. Wiring the Differential Input to Accept Single-Ended Levels Figure 1 shows how a differential input can be wired to accept single ended levels. The reference voltage VREF = VDD/2 is generated by the bias resistors R1 and R2. The bypass capacitor (C1) is used to help filter noise on the DC bias. This bias circuit should be located as close to the input pin as possible. The ratio of R1 and R2 might need to be adjusted to position the VREF in the center of the input voltage swing. For example, if the input clock swing is 2.5V and VDD = 3.3V, R1 and R2 value should be adjusted to set VREF at 1.25V. The values below are for when both the single ended swing and VDD are at the same voltage. This configuration requires that the sum of the output impedance of the driver (Ro) and the series resistance (Rs) equals the transmission line impedance. In addition, matched termination at the input will attenuate the signal in half. This can be done in one of two ways. First, R3 and R4 in parallel should equal the transmission line impedance. For most 50Ω applications, R3 and R4 can be 100Ω. The values of the resistors can be increased to reduce the loading for slower and weaker LVCMOS driver. When using single-ended signaling, the noise rejection benefits of differential signaling are reduced. Even though the differential input can handle full rail LVCMOS signaling, it is recommended that the amplitude be reduced. The datasheet specifies a lower differential amplitude, however this only applies to differential signals. For single-ended applications, the swing can be larger, however VIL cannot be less than -0.3V and VIH cannot be more than VDD + 0.3V. Though some of the recommended components might not be used, the pads should be placed in the layout. They can be utilized for debugging purposes. The datasheet specifications are characterized and guaranteed by using a differential signal. Figure 1. Recommended Schematic for Wiring a Differential Input to Accept Single-ended Levels ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 9 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Differential Clock Input Interface The CLKx /nCLKx accepts LVDS, LVPECL, LVHSTL, HCSL and other differential signals. Both signals must meet the VPP and VCMR input requirements. Figures 2A to 2E show interface examples for the CLKx/nCLKx input driven by the most common driver types. The input interfaces suggested here are examples only. Please consult with the vendor of the driver component to confirm the driver termination requirements. For example, in Figure 2A, the input termination applies for IDT open emitter LVHSTL drivers. If you are using an LVHSTL driver from another vendor, use their termination recommendation. 3.3V 3.3V 1.8V Zo = 50Ω Zo = 50Ω CLK Zo = 50Ω nCLK Zo = 50Ω nCLK CLK 3.3V LVPECL Differential Input R1 50Ω R2 50Ω Differential Input LVHSTL IDT LVHSTL Driver R1 50Ω R2 50Ω R2 50Ω Figure 2A. CLK/nCLK Input Driven by an IDT Open Emitter LVHSTL Driver Figure 2B. CLK/nCLK Input Driven by a 3.3V LVPECL Driver 3.3V 3.3V 3.3V Zo = 50Ω CLK Zo = 50Ω nCLK R1 100Ω CLK R3 125Ω R4 125Ω 3.3V Zo = 50Ω 3.3V LVPECL R1 84Ω R2 84Ω Differential Input Zo = 50Ω nCLK LVDS Receiver Figure 2C. CLK/nCLK Input Driven by a 3.3V LVPECL Driver Figure 2D. CLK/nCLK Input Driven by a 3.3V LVDS Driver 3.3V 3.3V *R3 33Ω Zo = 50Ω CLK Zo = 50Ω nCLK HCSL *R4 33Ω R1 50Ω R2 50Ω Differential Input *Optional – R3 and R4 can be 0Ω Figure 2E. CLK/nCLK Input Driven by a 3.3V HCSL Driver ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 10 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Power Considerations This section provides information on power dissipation and junction temperature for the ICS8344I-01. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS8344I-01 is the sum of the core power plus the analog power plus the power dissipated in the load(s). The following is the power dissipation for VDD = 3.3V + 5% = 3.465V, which gives worst case results. • • • • Power (core)MAX = VDD_MAX * IDD = 3.465V *95mA = 329.2mW Output Impedance ROUT Power Dissipation due to Loading 50Ω to VDD/2 Output Current IOUT = VDD_MAX / [2 * (50Ω + ROUT)] = 3.465V / [2 * (50Ω + 7Ω)] = 30.4mA Power Dissipation on the ROUT per LVCMOS output Power (ROUT) = ROUT * (IOUT)2 = 7Ω * (30.4mA)2 = 6.47mW per output Total Power (ROUT) = 6.47mW * 24 = 155mW Power (100MHz) = CPD * Frequency * (VDD)2 = 16pF * 100MHz * (3.465V)2 = 19.2mW per output Total Power (100MHz) = 19.2mW * 24 = 461mW Total Power Dissipation • Total Power = Power (core)MAX + Power (ROUT) + Power (100MHz) = 329.2mW + 155mW + 461mW = 945.2mW Dynamic Power Dissipation at 100MHz 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad directly affects the reliability of the device. The maximum recommended junction temperature is 125°C. Limiting the internal transistor junction temperature, Tj, to 125°C ensures that the bond wire and bond pad temperature remains below 125°C. The equation for Tj is as follows: Tj = θJA * Pd_total + TA Tj = Junction Temperature θJA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming no air flow and a multi-layer board, the appropriate value is 81.2°C/W per Table 6 below. Therefore, Tj for an ambient temperature of 70°C with all outputs switching is: 70°C + 0.945W *53.9°C/W = 120.9°C. This is below the limit of 125°C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow and the type of board (multi-layer). Table 6. Thermal Resistance θJA for 48 Lead LQFP, Forced Convection θJA by Velocity Meters per Second Multi-Layer PCB, JEDEC Standard Test Boards 0 53.9°C/W 1 47.7°C/W 2.5 45.0°C/W ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 11 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Reliability Information Table 7. θJA vs. Air Flow Table for a 48 Lead LQFP θJA vs. Air Flow Meters per Second Multi-Layer PCB, JEDEC Standard Test Boards 0 53.9°C/W 1 47.7°C/W 2.5 45.0°C/W Transistor Count The transistor count for ICS8344I-01 is: 1503 ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 12 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Package Outline and Package Dimensions Package Outline - Y Suffix for 48 Lead LQFP Table 7. Package Dimensions for 48 Lead LQFP JEDEC Variation: ABC - HD All Dimensions in Millimeters Symbol Minimum Nominal Maximum N 48 A 1.60 A1 0.05 0.10 0.15 A2 1.35 1.4 1.45 b 0.17 0.22 0.27 c 0.09 0.15 0.20 D&E 9.00 Basic D1 & E1 7.00 Basic D2 & E2 5.50 Ref. e 0.50 Basic L 0.45 0.60 0.75 θ 0° 7° ccc 0.08 Reference Document: JEDEC Publication 95, MS-026 ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 13 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER Ordering Information Table 8. Ordering Information Part/Order Number 8344AYI-01LF 8344AYI-01ILFT Marking ICS8344AI01L ICS8344AI01L Package “Lead-Free” 48 Lead LQFP “Lead-Free” 48 Lead LQFP Shipping Packaging Tray 1000 Tape & Reel Temperature -40°C to 70°C -40°C to 70°C NOTE: Parts that are ordered with an "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial and industrial applications. Any other applications, such as those requiring high reliability or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. ICS8344AYI-01 REVISION A FEBRUARY 29, 2012 14 ©2012 Integrated Device Technology, Inc. ICS8344I-01 Data Sheet LOW SKEW, 1-TO-24 DIFFERENTIAL-TO-LVCMOS/LVTTL FANOUT BUFFER We’ve Got Your Timing Solution 6024 Silver Creek Valley Road San Jose, California 95138 Sales 800-345-7015 (inside USA) +408-284-8200 (outside USA) Fax: 408-284-2775 www.IDT.com/go/contactIDT Technical Support netcom@idt.com +480-763-2056 DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright 2012. All rights reserved.