AS4624DZG8

DATASHEET 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH Description The IDTAS4624 low on-resistance (RON), low voltage, single-pole/double-throw (SPDT) analog switch operates from a single +1.8 V to +5.5 V supply. The IDTAS4624 features a 0.5Ω (max) RON for its NC switch and a 0.8Ω (max) RON for its NO switch at a +2.7 V supply. It also features break-before-make switching action (2 ns) with tON = 50 ns and tOFF = 40 ns at +3 V. The digital logic input is 1.8 V logic-compatible with a +2.7 V to +3.3 V supply. IDTAS4624 Features • • • • • • • • • • • • • +1.8 V to +5.5 V single-supply operation Rail-to-rail signal handling 1.8 V logic compatibility RON match between channels: 0.06Ω (max) RON flatness over signal range: 0.15Ω (max) NC Switch RON: 0.5Ω max (+2.7 V Supply) NO Switch RON: 0.8Ω max (+2.7 V Supply) Low crosstalk: -68dB (100 kHz) High Off-isolation: -64dB (100 kHz) THD: 0.03% 50 nA (max) supply current Low leakage currents: 1 nA (max) at TA = +25°C 6-pin SOT-23 package Applications • • • • • • • Speaker headset switching MP3 players Battery-operated equipment Audio and video signal routing PCMCIA cards Cellular phones Modems Block Diagram IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 1 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Pin Assignment (SOT-23) Truth Table IN 0 1 NO OFF ON NC ON OFF Note: Switches shown for logic “0” input. Pin Descriptions Pin Numbers 4 1 5 6 2 3 Pin Name NC IN COM1 NO V+ GND Digital control input. Pin Description Analog switch. Normally closed terminal. Analog switch. Common terminal 1. Analog switch. Normally open terminal. Positive supply voltage input. Ground. IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 2 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the IDTAS4624. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. All voltages referenced to ground. Symbol V+, IN COM, NO, NC Continuous current NO, NC, COM Rating Min -0.3 -0.3 Max +6 (V+ + 0.3) ±300 ±400 ±500 +909 Unit V V mA mW °C °C °C °C °C Peak current (pulsed at 1ms, 50% duty cycle) Peak current (pulsed at 1ms, 10% duty cycle) Continuous power dissipation (TA = +70°C) and 12-bump UCSP (derate 11.4mW/°C above +70°C) Operating temperature range 0 -65 +70 +150 +300 +200 +215 TSTG Storage temperature range Lead temperature (soldering, 10s) Bump temperature (soldering, infrared, 15s) Vapor phase (60s) IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 3 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Electrical Characteristics, +3 V Supply (notes 1, 2) Unless stated otherwise, V+ = 2.7 V to 3.3 V, VIH = 1.4 V, VIL = 0.5 V, TA = TMIN to TMAX. Typical values are at +3 V and 25°C Parameter Analog Signal Range NC On-Resistance NO On-Resistance On-Resistance Match between channels NC On-Resistance Flatness NO On-Resistance Flatness NO or NC Off-leakage Current COM On-leakage Current Symbol VNO, VNC, VCOM RON(NC) RON(NO) RON RFLAT(NC) RFLAT(NO) INO(OFF) or INC(OFF) ICOM(ON) Conditions Analog Switch TA TMIN to TMAX Min. 0 Typ. Max. Units V+ V Ω Ω Ω Ω Ω nA nA V+ = 2.7 V, ICOM = 100 mA, VNC = 0 to V+; Note 3 V+ = 2.7 V, ICOM = 100 mA, VNO = 0 to V+; Note 3 V+ = 2.7 V, ICOM = 100 mA, VNO or VNC = 1.5 V; Notes 3, 4 V+ = 2.7 V, ICOM = 100 mA, VNC = 0 to V+; Note 5 V+ = 2.7 V, ICOM = 100 mA, VNO = 0 to V+; Note 5 +25°C TMIN to TMAX +25°C TMIN to TMAX +25°C TMIN to TMAX TMIN to TMAX TMIN to TMAX -1 -10 -2 -20 3.0 0.45 0 0.5 0.5 0.8 0.8 0.6 0.6 0.15 0.35 +1 +10 +2 +20 V+ = 3.3 V, VNO or VNC = 3 V, 0.3 V +25°C VCOM = 0.3 V, 3 V TMIN to TMAX V+ = 3.3 V, VNO or VNC = 3 V, 0.3 +25°C V, or floating TMIN to TMAX VCOM = 0.3 V, 3 V, or floating Dynamic Characteristics Turn-on Time Turn-off Time Break-Before-Make-Delay Charge Injection Off-Isolation Crosstalk Total Harmonic Distortion NC Off-Capacitance NC Off-Capacitance NC On-Capacitance NC On-Capacitance tON tOFF tBBM Q VISO VCT THD CNC(OFF) CNO(OFF) CNC(ON) CNO(ON) V+ = 2.7 V, VNO or VNC = 1.5 V, , RL = 50Ω CL = 35 pF V+ = 2.7 V, VNO or VNC = 1.5 V, , RL = 50Ω CL = 35 pF V+ = 2.7 V, VNO or VNC = 1.5 V, , RL = 50Ω CL = 35 pF COM = 0, RS = 0, CL = 1 nF CL = 5 pF; RL = 50Ω, f = 100 kHz, VCOM = 1 VRMS, Note 6 f = 100 kHz, RL = 50Ω CL = 5 pF, , VCOM = 1 VRMS RL = 600Ω IN = 2 V p-p, , f = 20Hz to 20 kHz f = 1 MHz f = 1 MHz f = 1 MHz f = 1 MHz +25°C TMIN to TMAX +25°C TMIN to TMAX TMIN to TMAX +25°C +25°C +25°C +25°C +25°C +25°C +25°C +25°C 2 15 200 -64 -68 0.03 84 37 190 150 25 30 50 60 30 40 ns ns ns ns ns pC dB dB % pF pF pF pF IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 4 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Parameter Input Logic HIGH Input Logic LOW IN Input Leakage Current Symbol VIH VIL IIN Conditions Digital I/O TA TMIN to TMAX TMIN to TMAX Min. 1.4 Typ. Max. Units V 0.5 V µA VIN = 0 or V+ TMIN to TMAX TMIN to TMAX -1 1 Power Supply Power Supply Range Supply Current V+ I+ 1.8 -50 -200 +0.04 5.5 +50 +200 V nA V+ = 5.5 V, VIN = 0 or V+, Note 3 +25°C TMIN to TMAX Notes: 1. The algebraic convention used in this data sheet is where the most negative value is a minimum and the most positive value a maximum. 2. UCSP parts are 100% tested at +25°C only and guaranteed by design and correlation at the full hot-rated temperature. 3. Guaranteed by design. 4. RON = RON(MAX) - RON(MIN), between NC and NO. 5. Flatness is defined as the difference between the maximum and minimum value of on resistance as measured over the specified analog signal ranges. 6. Off-isolation = 20log10 (VCOM / VCO), VCOM = output, VCO = input to off switch. IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 5 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Electrical Characteristics, +5 V Supply (Note 1) Unless stated otherwise, V+ = 5 V ±10%, GND = 0, VIH = +2.4 V, VIL = +0.8 V, TA = TMIN to TMAX. Typical values are at +3 V and +25°C Parameter Analog Signal Range On-Resistance On-Resistance Match between channels On-Resistance Flatness NO or NC Off-leakage Current COM On-leakage Current Symbol VNO, VNC, VCOM RON RON RFLAT(ON) INO(OFF) or INC(OFF) ICOM(ON) Conditions Analog Switch TA Min. 0 Typ. Max. Units V+ V Ω Ω Ω nA nA V+ = 4.5 V, ICOM = 100 mA, VNC or VNO = 3.5 V V+ = 4.5 V, ICOM = 100 mA, VNC or VNO = 3.5 V V+ = 4.5 V, ICOM = 100 mA, VNC or VNO = 0V, 1 V, 2 V, Note 3 +25°C TMIN to TMAX +25°C TMIN to TMAX +25°C TMIN to TMAX -2 -20 -4 -40 0.65 0.6 0.8 0.01 0.3 1 1.2 0.12 0.15 0.12 0.15 +2 +20 +4 +40 V+ = 5.5 V, VNO or VNC = 1 V, 4.5 V +25°C VCOM = 1 V, 4.5 V TMIN to TMAX +25°C V+ = 5.5 V, VNO or VNC = 1 V, 4.5 V, or floating TMIN to TMAX VCOM = 1 V, 4.5 V TA = +25°C Overcurrent-Protection Current Threshold 1.2 A Dynamic Characteristics Turn-on Time Turn-off Time Break-Before-Make-Delay Charge Injection Off-Isolation Crosstalk NC or NO Off-Capacitance COM On-Capacitance tON tOFF tBBM Q OIRR VCT COFF CCOM(ON) VNO or VNC = 3 V VNO or VNC = 3 V Note 4 VGEN = 0, RGEN = 0, CL = 1 nF CL = 5 pF; RL = 50Ω, f = 1 MHz CL = 5 pF; RL = 50Ω, f = 1 MHz, Note 5 f = 1 MHz f = 1 MHz +25°C TMIN to TMAX +25°C TMIN to TMAX +25°C TMIN to TMAX +25°C +25°C +25°C +25°C +25°C 1 1 200 -64 -68 37 190 pC dB dB pF pF 20 40 40 50 60 50 60 ns ns ns IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 6 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Parameter Input Voltage HIGH Input Voltage LOW Logic Input Current Symbol VINH VINL IIN Conditions Logic Input TA Min. 2.4 Typ. Max. Units V 0.8 V µA +1 -1 Power Supply Power Supply Range Positive Supply Current V+ I+ 1.8 5.5 10 V nA V+ = 5.5 V, VIN = 0 or V+ Notes: 1. The algebraic convention used in this data sheet is where the most negative value is a minimum and the most positive value a maximum. 2. Guaranteed by design. 3. RON = RON(MAX) - RON(MIN), between NC and NO. 4. Flatness is defined as the difference between the maximum and minimum value of on resistance as measured over the specified analog signal ranges. 5. Off-isolation = 20log10 (VCOM / VCO), VCOM = output, VCO = input to off switch. IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 7 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Test Circuits and Timing Diagrams Overvoltage Protection Using Two External Blocking Diodes Switching Time IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 8 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Break-Before-Make Interval Charge Injection IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 9 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH On-Loss, Off-Isolation, and Crosstalk Channel Off/On Capacitance IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 10 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Marking Diagram (SOT-23) TBD Notes: 1. “Z” is the device step (1 to 2 characters). 2. YYWW is the last two digits of the year and week that the part was assembled. 3. “$” is the assembly mark code. 4. “G” after the two-letter package code designates RoHS compliant package. 5. “I” at the end of part number indicates industrial temperature range. 6. Bottom marking: country of origin if not USA. IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 11 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Package Outline and Package Dimensions (SOT-23-6) Package dimensions are kept current with JESD Publication No. 95-1, Millimeters Symbol Min Max Inches Min Max A A1 A2 b c D E E1 e e1 L L1 L2 θ aaa 0.90 1.45 0 0.15 0.90 1.30 0.35 0.50 0.09 0.22 2.80 3.00 2.60 3.00 1.50 1.75 0.95 BASIC 1.90 BASIC 0.35 0.55 0.50 0.70 0.25 BASIC 0° 10° — 0.10 .0354 .0571 0 .0059 .0354 .0512 .0138 .0197 .0036 .0087 .1102 .1181 .1024 .1181 .0591 .0689 0.0374 BASIC 0.0748 BASIC .0138 .0217 .0197 .0276 .0098 BASIC 0° 10° — .0039 IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 12 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Ordering Information XXXXXX Device Type XXX Package X Temp. Range X Shipping Carrier 8 Tape and Reel Blank Commercial (0 to +70°C) DZG SOT-23 Package AS4624 0.5Ω Low Voltage, Single SPDT Analog Switch IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 13 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Revision History Rev. B C D S. S. Originator Date 6/12/07 05/07/09 08/12/09 Description of Change Created datasheet in new template; added marking diagram. Updated Ordering information. Updated truth table pg.2; block diagram. IDT™ 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH 14 IDTAS4624 REV D 081209 IDTAS4624 0.5Ω LOW VOLTAGE, SINGLE SPDT ANALOG SWITCH ANALOG SWITCH Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 For Tech Support www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA