IDT5T9306_08

2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II FEATURES: • • • • • • • • • • • • Guaranteed Low Skew < 25ps (max) Very low duty cycle distortion < 125ps (max) High speed propagation delay < 1.75ns (max) Additive phase jitter, RMS 0.159ps (typical) @ 125MHz Up to 1GHz operation Selectable inputs Hot insertable and over-voltage tolerant inputs 3.3V / 2.5V LVTTL, HSTL, eHSTL, LVEPECL (2.5V), LVPECL (3.3V), CML, or LVDS input interface Selectable differential inputs to six LVDS outputs Power-down mode 2.5V VDD Available in VFQFPN package IDT5T9306 DESCRIPTION: The IDT5T9306 2.5V differential clock buffer is a user-selectable differential input to six LVDS outputs. The fanout from a differential input to six LVDS outputs reduces loading on the preceding driver and provides an efficient clock distribution network. The IDT5T9306 can act as a translator from a differential HSTL, eHSTL, LVEPECL (2.5V), LVPECL (3.3V), CML, or LVDS input to LVDS outputs. A single-ended 3.3V / 2.5V LVTTL input can also be used to translate to LVDS outputs. The redundant input capability allows for an asynchronous change-over from a primary clock source to a secondary clock source. Selectable reference inputs are controlled by SEL. The IDT5T9306 outputs can be asynchronously enabled/disabled. When disabled, the outputs will drive to the value selected by the GL pin. Multiple power and grounds reduce noise. APPLICATIONS: • Clock distribution FUNCTIONAL BLOCK DIAGRAM GL G OUTPUT CONTROL Q1 Q1 PD OUTPUT CONTROL Q2 Q2 A1 A1 1 OUTPUT CONTROL Q3 Q3 A2 A2 0 OUTPUT CONTROL Q4 Q4 SEL OUTPUT CONTROL Q5 Q5 OUTPUT CONTROL Q6 Q6 IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 1 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II PIN CONFIGURATION SEL VDD 28 27 26 25 24 23 22 G VDD Q1 Q1 VDD A1 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 GND 21 20 19 18 17 16 15 PD VDD Q4 Q4 VDD A2 A2 VDD VFQFPN TOP VIEW IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 2 VDD GL Q2 Q2 Q3 Q3 NC Q6 Q6 Q5 Q5 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II ABSOLUTE MAXIMUM RATINGS(1) Symbol VDD VI VO TSTG TJ Input Voltage Output Voltage(2) Storage Temperature Junction Temperature Description Power Supply Voltage Max –0.5 to +3.6 –0.5 to +3.6 –0.5 to VDD +0.5 –65 to +150 150 Unit V V V °C °C CAPACITANCE(1) (TA = +25°C, F = 1.0MHz) Symbol CIN Parameter Input Capacitance Min Typ. Max. 3 Unit pF — — NOTE: 1. This parameter is measured at characterization but not tested NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Not to exceed 3.6V. RECOMMENDED OPERATING RANGE Symbol TA VDD Description Ambient Operating Temperature Internal Power Supply Voltage Min. –40 2.3 Typ. +25 2.5 Max. +85 2.7 Unit °C V PIN DESCRIPTION Symbol A[1:2] A[1:2] I/O I I Type Adjustable(1,4) Adjustable(1,4) Description Clock input. A[1:2] is the "true" side of the differential clock input. Complementary clock inputs. A[1:2] is the complementary side of A[1:2]. For LVTTL single-ended operation, A[1:2] should be set to the desired toggle voltage for A[1:2]: 3.3V LVTTL VREF = 1650mV 2.5V LVTTL VREF = 1250mV Gate control for differential outputs Q1 and Q1 through Q6 and Q6. When G is LOW, the differential outputs are active. When G is HIGH, the differential outputs are asynchronously driven to the level designated by GL(2). Specifies output disable level. If HIGH, "true" outputs disable HIGH and "complementary" outputs disable LOW. If LOW, "true" outputs disable LOW and "complementary" outputs disable HIGH. Clock outputs Complementary clock outputs Reference clock select. When LOW, selects A2 and A2. When HIGH, selects A1 and A1. Power-down control. Shuts off entire chip. If LOW, the device goes into low power mode. Inputs and outputs are disabled. Both "true" and "complementary" outputs will pull to VDD. Set HIGH for normal operation.(3) Power supply for the device core and inputs Power supply return for all power No connect; recommended to connect to GND G GL Qn Q n SEL P D VDD GND NC I I O O I I LVTTL LVTTL LVDS LVDS LVTTL LVTTL PWR PWR NOTES: 1. Inputs are capable of translating the following interface standards: Single-ended 3.3V and 2.5V LVTTL levels Differential HSTL and eHSTL levels Differential LVEPECL (2.5V) and LVPECL (3.3V) levels Differential LVDS levels Differential CML levels 2. Because the gate controls are asynchronous, runt pulses are possible. It is the user's responsibility to either time the gate control signals to minimize the possibility of runt pulses or be able to tolerate them in down stream circuitry. 3. It is recommended that the outputs be disabled before entering power-down mode. It is also recommended that the outputs remain disabled until the device completes powerup after asserting PD. 4. The user must take precautions with any differential input interface standard being used in order to prevent instability when there is no input signal. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 3 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR LVTTL(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage VIN DC Input Voltage VIH DC Input HIGH VIL DC Input LOW VTHI DC Input Threshold Crossing Voltage Single-Ended Reference Voltage(3) VREF Test Conditions VDD = 2.7V VDD = 2.7V VDD = 2.3V, IIN = -18mA Min. — — — - 0.3 1.7 — — — — Typ.(2) — — - 0.7 — — — VDD /2 1.65 1.25 Max ±5 ±5 - 1.2 +3.6 — 0.7 — — — Unit μA V V V V V V 3.3V LVTTL 2.5V LVTTL NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. Typical values are at VDD = 2.5V, +25°C ambient. 3. For A[1:2] single-ended operation, A[1:2] is tied to a DC reference voltage. DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR DIFFERENTIAL INPUTS(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage VIN DC Input Voltage VDIF DC Differential Voltage(3) VCM DC Common Mode Input Voltage(4) Test Conditions VDD = 2.7V VDD = 2.7V VDD = 2.3V, IIN = -18mA Min. — — — - 0.3 0.1 0.05 Typ.(2) — — - 0.7 — — — Max ±5 ±5 - 1.2 +3.6 — VDD Unit μA V V V V NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. Typical values are at VDD = 2.5V, +25°C ambient. 3. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching to a new state. 4. VCM specifies the maximum allowable range of (VTR + VCP) /2. DC ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING RANGE FOR LVDS(1) Symbol Parameter Output Characteristics VOT(+) Differential Output Voltage for the True Binary State VOT(-) Differential Output Voltage for the False Binary State ΔVOT Change in VOT Between Complementary Output States VOS Output Common Mode Voltage (Offset Voltage) ΔVOS Change in VOS Between Complementary Output States IOS Outputs Short Circuit Current Differential Outputs Short Circuit Current IOSD NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. Typical values are at VDD = 2.5V, TA = +25°C ambient. Test Conditions Min. 247 247 — 1.125 — — — Typ.(2) — — — 1.2 — 12 6 Max 454 454 50 1.375 50 24 12 Unit mV mV mV V mV mA mA VOUT + and VOUT - = 0V VOUT + = VOUT - IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 4 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II DIFFERENTIAL INPUT AC TEST CONDITIONS FOR HSTL Symbol VDIF VX DH VTHI tR, tF Parameter Input Signal Swing(1) Differential Input Signal Crossing Point Duty Cycle Input Timing Measurement Reference Level Input Signal Edge Rate(4) (3) (2) Value 1 750 50 Crossing Point 2 Units V mV % V V/ns NOTES: 1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 750mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. DIFFERENTIAL INPUT AC TEST CONDITIONS FOR eHSTL Symbol VDIF VX DH VTHI tR, tF Parameter Input Signal Swing(1) Differential Input Signal Crossing Point Duty Cycle Input Timing Measurement Reference Level Input Signal Edge Rate(4) (3) (2) Value 1 900 50 Crossing Point 2 Units V mV % V V/ns NOTES: 1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 900mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVEPECL (2.5V) AND LVPECL (3.3V) Symbol VDIF VX DH VTHI tR, tF Parameter Input Signal Swing (1) Value 732 LVEPECL LVPECL 1082 1880 50 (3) Units mV mV % V V/ns Differential Input Signal Crossing Point(2) Duty Cycle Input Timing Measurement Reference Level Input Signal Edge Rate(4) Crossing Point 2 NOTES: 1. The 732mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. 1082mV LVEPECL (2.5V) and 1880mV LVPECL (3.3V) crossing point levels are specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 5 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVDS Symbol VDIF VX DH VTHI tR, tF Parameter Input Signal Swing(1) Differential Input Signal Crossing Point Duty Cycle Input Timing Measurement Reference Level(3) Input Signal Edge Rate(4) (2) Value 400 1.2 50 Crossing Point 2 Units mV V % V V/ns NOTES: 1. The 400mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 1.2V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. AC DIFFERENTIAL INPUT SPECIFICATIONS(1) Symbol VDIF VIX VCM VIN Parameter AC Differential Voltage(2) Differential Input Crosspoint Voltage Common Mode Input Voltage Range(3) Input Voltage Min. 0.1 0.05 0.05 - 0.3 Typ. — — — Max 3.6 VDD VDD +3.6 Unit V V V V NOTES: 1. The output will not change state until the inputs have crossed and the minimum differential voltage range defined by VDIF has been met or exceeded. 2. VDIF specifies the minimum input voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. The AC differential voltage must be achieved to guarantee switching to a new state. 3. VCM specifies the maximum allowable range of (VTR + VCP) /2. POWER SUPPLY CHARACTERISTICS FOR LVDS OUTPUTS(1) Symbol IDDQ ITOT IPD Parameter Quiescent VDD Power Supply Current Total Power VDD Supply Current Total Power Down Supply Current Test Conditions VDD = Max., All Input Clocks = LOW(2) Outputs enabled VDD = 2.7V., FREFERENCE CLOCK = 1GHz PD = LOW Typ. — Max 240 250 5 Unit mA mA mA — — NOTES: 1. These power consumption characteristics are for all the valid input interfaces and cover the worst case conditions. 2. The true input is held LOW and the complementary input is held HIGH. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 6 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II AC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE(1,5) Symbol Skew Parameters tSK(O) tSK(P) tSK(PP) Propagation Delay tPLH tPHL Parameter Same Device Output Pin-to-Pin Skew(2) Pulse Skew(3) Part-to-Part Skew(4) Propagation Delay A, A Crosspoint to Qn, Qn Crosspoint Min. — — Typ. Max 25 125 300 1.75 1 3.5 3.5 100 100 Unit ps ps ps ns GHz ns ns μS μS ps ps ps 600 ps — — — — — — — — — — 1.25 fO Frequency Range(6) Output Gate Enable/Disable Delay tPGE tPGD Power Down Timing Output Gate Enable Crossing VTHI to Qn/Qn Crosspoint Output Gate Disable Crossing VTHI to Qn/Qn Crosspoint Driven to GL Designated Level — — — — — 0.541 0.159 0.185 tPWRDN PD Crossing VTHI to Qn = VDD, Qn = VDD Output Gate Disable Crossing VTHI to Qn/Qn Driven to GL Designated Level tPWRUP RMS Additive Phase Jitter RMS Additive Phase Jitter @ 25MHz (12kHz – 10MHz Integration Range) tJIT RMS Additive Phase Jitter @ 125MHz (12kHz – 20MHz Integration Range) RMS Additive Phase Jitter @ 156.25MHz (12kHz – 20MHz Integration Range) Output Rise/Fall Time tR/tF Output Rise/Fall Time(6), (20% - 80%) 125 NOTES: 1. AC propagation measurements should not be taken within the first 100 cycles of startup. 2. Skew measured between crosspoints of all differential output pairs under identical input and output interfaces, transitions and load conditions on any one device. 3. Skew measured is the difference between propagation delay times tPHL and tPLH of any differential output pair under identical input and output interfaces, transitions and load conditions on any one device. 4. Skew measured is the magnitude of the difference in propagation times between any single differential output pair of two devices, given identical transitions and load conditions at identical VDD levels and temperature. 5. All parameters are tested with a 50% input duty cycle. 6. Guaranteed by design but not production tested. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 7 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II DIFFERENTIAL AC TIMING WAVEFORMS 1/fo A[1:2] - A[1:2] + VDIF VDIF = 0 - VDIF tPLH tPHL + VDIF VDIF = 0 - VDIF tSK(O) + VDIF VDIF = 0 - VDIF Qn - Qn tSK(O) Qm - Qm Output Propagation and Skew Waveforms NOTES: 1. Pulse skew is calculated using the following expression: tSK(P) = | tPHL - tPLH | Note that the tPHL and tPLH shown above are not valid measurements for this calculation because they are not taken from the same pulse. 2. AC propagation measurements should not be taken within the first 100 cycles of startup. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 8 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II A[1:2] - A[1:2] + VDIF VDIF = 0 - VDIF VIH VTHI VIL tPLH VIH VTHI VIL tPGD tPGE + VDIF VDIF = 0 - VDIF GL G Qn - Qn Differential Gate Disable/Enable Showing Runt Pulse Generation NOTE: 1. As shown, it is possible to generate runt pulses on gate disable and enable of the outputs. It is the user's responsibility to time the G signal to avoid this problem. A1 - A1 +VDIF VDIF=0 -VDIF +VDIF VDIF=0 -VDIF VIH VTHI VIL VIH VTHI VIL +VDIF VDIF=0 -VDIF A2 - A2 G PD Qn - Qn Power Down Timing NOTES: 1. It is recommended that outputs be disabled before entering power-down mode. It is also recommended that the outputs remain disabled until the device completes power-up after asserting PD. 2. The POWER DOWN TIMING diagram assumes that GL is HIGH. 3. It should be noted that during power-down mode, the outputs are both pulled to VDD. In the POWER DOWN TIMING diagram this is shown when Qn-Qn goes to VDIF = 0. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 9 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II TEST CIRCUITS AND CONDITIONS VIN ~50Ω Transmission Line VDD/2 A Pulse Generator VIN D.U.T. ~50Ω Transmission Line A -VDD/2 Scope 50Ω 50Ω Test Circuit for Differential Input DIFFERENTIAL INPUT TEST CONDITIONS Symbol VTHI VDD = 2.5V ± 0.2V Crossing of A and A Unit V IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 10 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II VDD Pulse Generator A A Qn RL D.U.T. RL Qn VOS VOD Test Circuit for DC Outputs and Power Down Tests VDD/2 CL Z = 50Ω SCOPE Pulse Generator A A Qn D.U.T. Qn Z = 50Ω CL -VDD/2 50Ω 50Ω Test Circuit for Propagation, Skew, and Gate Enable/Disable Timing LVDS OUTPUT TEST CONDITION Symbol CL RL VDD = 2.5V ± 0.2V 0(1) 8(1,2) 50 Unit pF Ω NOTES: 1. Specifications only apply to "Normal Operations" test condition. The TIA/EIA specification load is for reference only. 2. The scope inputs are assumed to have a 2pF load to ground. TIA/EIA - 644 specifies 5pF between the output pair. With CL = 8pF, this gives the test circuit appropriate 5pF equivalent load. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 11 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II RECOMMENDED LANDING PATTERN NL 28 pin NOTE: All dimensions are in millimeters. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 12 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II July 23, 2002 October 8, 2002 October 10, 2002 October 24, 2002 November 1, 2002 December 12, 2002 December 16, 2002 May 8, 2003 August 7, 2003 October 2, 2003 March 26, 2004 June 22, 2004 October 26, 2004 October 27, 2004 October 29, 2004 March 9, 2005 October 23, 2007 April 15, 2008 Datasheet creation Page 1, entire page changed; page 2, both diagrams; page 3, Pin Description and notes; page 4, DC Cha. for LVPECL and Differential Input tables; page 6, DC Cha. and Power Supply tables; page 7, entire page; page 9, added note 3; page 10, entire page; page 10, entire page; page 11, entire page; page 12, Ordering Info; added 3 new pages (10 thru 12) of diagrams. Page 1, entire page changed; page 2, both diagrams; page 3, Pin Description and notes; page 7, AC Cha. table; page 8, added new LVPECL table; page 10, removed Input Clock Switching diagram; page 11, deleted entire page; page 12, changed Power Down Timing; page 15, Ordering Info. Page 2, added note 1 to TQFP TOP VIEW text; page3, aded note 4 to Pin Description; page 4, replaced "Compliant devices must meet" with the text "This device meets" in four instances; page 5, Differential Input table, note 1, changed 1V to 732mV and replaced "Compliant devices must meet" with the text "This device meets"; page 6, DC Electrical table, Vdif row, changed Min. value to 0.1, and under Differential Input table replaced "Compliant devices must meet" with the text "This device meets" page 7, Power Supply table, replaced ((TBD)) with 800MHz, and under AC Electrical table, replaced ((TBD)) with 500; page 8, completely altered AC DIfferential table; page 12, LVDS Output table, replaced ((TBD)) with 3. Radical changes to entire document. Radical changes to entire document, using 5T9316 as a base. Throughout document, removed "Differential" from title; page 7, Power Supply table, changed Max values, changed FREFERENCE value; page 10, note 1, changed Gx to G. Page 2, corrected pinout diagram. Page 1, Features text, 3rd bullet, changed 2ns to 1.75ns, 4th bullet, changed 800MHz to 1GHz, and 7th bullet, added CML, on Description, 3rd line, added CML to list; page 4, Pin Descr., note 1, added "Differential CML levels", for Description of PD row, replaced 2nd sentence with "Both 'true' and 'complementary' output will pull to Vdd"; page 5, DC... for Differential Inputs table, removed note 5 and changed Vcm Max. from 3.5 to Vdd; page 7, Power Supply table, changed 800MHz to 1GHz; page 8, AC Differential table, changed Vix and Vcm Max specs from 3.5V to Vdd, removed notes 4 and 5, and placed entire table on page 7, for AC Elect. table, added notes 5 and 6, changed ((TBD)) to 300ps, tplh Type to 1.25ns, and Max from 2ns to 1.75ns, and changed fo Max from 800MHz to 1GHz. Page 1, Features, 7th bullet, added "3.3V / 2,5V LVTTL" to front, Description, added to 1st paragraph "A single-ended 3.3V / 2.5V LVTTL input can also be used to translate to LVDS outputs."; page 4, Pin Description table, added large block of text to 2nd row, added "Single-ended 3.3V and 2.5V LVTTL levels" to note 1; page 5, DC for LVTTL table, added Vref row and note 3, for DC for LVDS table, changed Ios ratings from 5 Typ, 7.5 Max to 12 Typ, 24 Max, and changed Iosd ratings from 5 Typ, 7.5 Max to 6 Typ, 12 Max; page 7, Power Supply table, changed Ipd from 3 to 5. Page 2, changed pin 22 to NC; page 3, changed pin 25 to NC; page 4, added NC row to Pin Description. Removed TQFP package. Inserted a page before Ordering Info and added Landing Pattern. Added note to Landing Pattern. Changed landing pattern diagram. Page 6, switched Iddq and Itot values. Page 7, added Additive Phase Jitter, RMS specs to the AC Electrical Characterisitcs Table. Page 7, added Rise/Fall Time spec. to the AC Electrical Characteristics Table. IDT™ / ICS™ LVDS CLOCK BUFFER TERABUFFER™ II 13 IDT5T9306 REV. B APRIL 15, 2008 IDT5T9306 2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II ORDERING INFORMATION IDT XXXXX Device Type XX Package X Process I -40°C to +85°C (Industrial) NL Thermally Enhanced Plastic Very Fine Pitch Quad Flat No Lead Package 5T9306 2.5V 1:6 LVDS Clock Buffer Terabuffer™ II Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales 800-345-7015 (inside USA) +408-284-8200 (outside USA) Fax: 408-284-2775 www.IDT.com/go/contactIDT For Tech Support netcom@idt.com +480-763-2056 Corporate Headquarters Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800-345-7015 (inside USA) +408-284-8200 (outside USA) © 2008 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT, the IDT logo, ICS and HiPerClockS are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA