IDT60LVCR2245ASO

IDT74LVCR2245A 3.3V CMOS OCTAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE 3.3V CMOS OCTAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS AND 5 VOLT TOLERANT I/O • 0.5 MICRON CMOS Technology • ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) • VCC = 3.3V ± 0.3V, Normal Range • VCC = 2.7V to 3.6V, Extended Range • CMOS power levels (0.4µ W typ. static) • Rail-to-rail output swing for increased noise margin • All inputs, outputs, and I/O are 5V tolerant • Available in SOIC, SSOP, QSOP, and TSSOP packages IDT74LVCR2245A FEATURES: DESCRIPTION: DRIVE FEATURES: APPLICATIONS: The LVCR2245A octal bus transceiver is built using advanced dual metal CMOS technology. This device is designed for asynchronous communication between data buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so the buses are effectively isolated. The LVCR2245A has series resistors in the output structure which will significantly reduce line noise when used with light loads. The driver has been designed to drive ±12mA at the designated threshold. Inputs can be driven from either 3.3V or 5V devices. This feature allows the use of this device as a translator in a mixed 3.3V/5V environment. • Balanced Output Drivers: ±12mA (B Port) • Low switching noise • 5V and 3.3V mixed voltage systems • Data communication and telecommunication systems FUNCTIONAL BLOCK DIAGRAM DIR 1 19 2 18 OE A1 B1 TO SEVEN OTHER CHANNELS The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE 1 © 1999 Integrated Device Technology, Inc. OCTOBER 1999 DSC-4610/1 IDT74LVCR2245A 3.3V CMOS OCTAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE PIN CONFIGURATION 20 19 18 17 16 15 14 13 12 11 ABSOLUTE MAXIMUM RATINGS(1) Symbol Description Max VTERM Terminal Voltage with Respect to GND Storage Temperature DC Output Current Continuous Clamp Current, V I < 0 o r VO < 0 Continuous Current through each VCC or GND –0.5 to +6.5 –65 to +150 –50 to +50 –50 ±100 TSTG IOUT IIK IOK ICC ISS Unit V °C mA mA mA DIR A1 A2 A3 A4 A5 A6 A7 A8 GND 1 2 3 4 5 6 7 8 9 10 VCC OE B1 B2 B3 B4 B5 B6 B7 B8 NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. CAPACITANCE (TA = +25°C, F = 1.0MHz) Symbol CIN COUT CI/O Parameter(1) Input Capacitance Output Capacitance I/O Port Capacitance Conditions VIN = 0V VOUT = 0V VIN = 0V Typ. 4.5 5.5 6.5 Max. 6 8 8 Unit pF pF pF SOIC/ SSOP/ QSOP/ TSSOP TOP VIEW NOTE: 1. As applicable to the device type. PIN DESCRIPTION Pin Names OE Ax, Bx DIR Description Output Enable Input (Active LOW) Data Inputs or 3-State Outputs Direction Control Output FUNCTION TABLE(1) Inputs OE L L H DIR L H X Outputs B Data to A Bus A Data to B Bus Isolation NOTE: 1. H = HIGH Voltage Level X = Don’t Care L = LOW Voltage Level 2 IDT74LVCR2245A 3.3V CMOS OCTAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Condition: TA = –40°C to +85°C Symbol VIH VIL IIH IIL IOZH IOZL IOFF VIK VH ICCL ICCH ICCZ ∆ICC High Impedance Output Current (3-State Output pins) Input/Output Power Off Leakage Clamp Diode Voltage Input Hysteresis Quiescent Power Supply Current VCC = 0V, VIN or VO ≤ 5.5V VCC = 2.3V, IIN = –18mA VCC = 3.3V VCC = 3.6V VIN = GND or VCC — — — — — — — –0.7 100 — — — ±50 –1.2 — 10 10 500 µA V mV µA VCC = 3.6V VO = 0 to 5.5V — — ±10 µA Parameter Input HIGH Voltage Level Input LOW Voltage Level Input Leakage Current VCC = 2.3V to 2.7V VCC = 2.7V to 3.6V VCC = 2.3V to 2.7V VCC = 2.7V to 3.6V VCC = 3.6V VI = 0 to 5.5V Test Conditions Min. 1.7 2 — — — Typ.(1) — — — — — Max. — — 0.7 0.8 ±5 µA V Unit V Quiescent Power Supply Current Variation 3.6 ≤ VIN ≤ 5.5V(2) One input at VCC - 0.6V, other inputs at VCC or GND µA NOTES: 1. Typical values are at VCC = 3.3V, +25°C ambient. 2. This applies in the disabled state only. OUTPUT DRIVE CHARACTERISTICS Symbol VOH Parameter Output HIGH Voltage VCC = 2.3V VCC = 2.7V VCC = 3V VOL Output LOW Voltage VCC = 2.3V to 3.6V VCC = 2.3V VCC = 2.7V VCC = 3V Test Conditions(1) VCC = 2.3V to 3.6V IOH = – 0.1mA IOH = – 4mA IOH = – 6mA IOH = – 4mA IOH = – 8mA IOH = – 6mA IOH = – 12mA IOL = 0.1mA IOL = 4mA IOL = 6mA IOL = 4mA IOL = 8mA IOL = 6mA IOL = 12mA Min. VCC – 0.2 1.9 1.7 2.2 2 2.4 2 — — — — — — — Max. — — — — — — — 0.2 0.4 0.55 0.4 0.6 0.55 0.8 V Unit V NOTE: 1. VIH and VIL must be within the min. or max. range shown in the DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table for the appropriate VCC range. TA = – 40°C to + 85°C. 3 IDT74LVCR2245A 3.3V CMOS OCTAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE OPERATING CHARACTERISTICS, VCC = 3.3V ± 0.3V, TA = 25°C Symbol CPD CPD Parameter Power Dissipation Capacitance per Transceiver Outputs enabled Power Dissipation Capacitance per Transceiver Outputs disabled Test Conditions CL = 0pF, f = 10Mhz Typical 48 4 Unit pF SWITCHING CHARACTERISTICS(1) Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tSK(o) Parameter Propagation Delay Ax to Bx or Bx to Ax Output Enable Time OE or DIR to Ax or Bx Output Disable Time OE or DIR to Ax or Bx Output Skew(2) Min. — — — — VCC = 2.7V Max. 7.3 9.5 8.5 VCC = 3.3V ± 0.3V Min. Max. 1.5 6.3 1.5 1.7 8.2 7.8 1 Unit ns ns ns ns — — NOTES: 1. See TEST CIRCUITS AND WAVEFORMS. TA = – 40°C to + 85°C. 2. Skew between any two outputs of the same package and switching in the same direction. 4 IDT74LVCR2245A 3.3V CMOS OCTAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS Symbol VLOAD VIH VT VLZ VHZ CL VCC(1)= 3.3V±0.3V VCC(1)= 2.7V 6 2.7 1.5 300 300 50 6 2.7 1.5 300 300 50 VCC(2)= 2.5V±0.2V 2 x Vcc Vcc Vcc / 2 150 150 30 Unit V V V mV mV pF SAME PHASE INPUT TRANSITION tPLH OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL tPHL VIH VT 0V VOH VT VOL VIH VT 0V LVC Link VCC 500Ω Pulse (1, 2) Generator VIN D.U.T. RT 500Ω CL VOUT VLOAD Open GND CONTROL INPUT Propagation Delay ENABLE DISABLE VIH VT 0V VLOAD/2 VOL+VLZ VOL VOH VOH-VHZ 0V LVC Link tPZL OUTPUT SWITCH NORMALLY VLOAD LOW tPZH OUTPUT SWITCH NORMALLY GND HIGH VLOAD/2 VT tPHZ VT 0V tPLZ LVC Link Test Circuit for All Outputs DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. NOTES: 1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2ns. NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. Enable and Disable Times SWITCH POSITION Test Open Drain Disable Low Enable Low Disable High Enable High All Other Tests Switch VLOAD GND Open DATA INPUT TIMING INPUT ASYNCHRONOUS CONTROL SYNCHRONOUS CONTROL VIH VT 0V VOH VT VOL VOH VT VOL tSU tH tREM tSU tH VIH VT 0V VIH VT 0V VIH VT 0V VIH VT 0V LVC Link INPUT Set-up, Hold, and Release Times tPLH1 tPHL1 OUTPUT 1 tSK (x) tSK (x) LOW-HIGH-LOW PULSE tW HIGH-LOW-HIGH PULSE VT OUTPUT 2 tPLH2 tPHL2 VT Pulse Width LVC Link LVC Link tSK(x) = tPLH2 - tPLH1 or tPHL2 - tPHL1 Output Skew - tSK(X) NOTES: 1. For tSK(o) OUTPUT1 and OUTPUT2 are any two outputs. 2. For tSK(b) OUTPUT1 and OUTPUT2 are in the same bank. 5 IDT74LVCR2245A 3.3V CMOS OCTAL BUS TRANSCEIVER WITH 3-STATE OUTPUTS INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION X LVC IDT XX XXXX XX Temp. Range Bus-Hold Device Type Package SO PY Q PG Small Outline IC (gull wing) Shrink Small Outline Package Quarter Size Small Outline Package Thin Shrink Small Outline Package R2245A Octal Bus Transceiver with 3-State Outputs, ±12mA Blank 74 No Bus-hold –40°C to +85°C CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com for Tech Support: logichelp@idt.com (408) 654-6459 6