IDT70T3589S166BC

Features: ◆ ◆ HIGH-SPEED 2.5V 256/128/64K x 36 IDT70T3519/99/89S SYNCHRONOUS DUAL-PORT STATIC RAM WITH 3.3V OR 2.5V INTERFACE – Data input, address, byte enable and control registers – Self-timed write allows fast cycle time Separate byte controls for multiplexed bus and bus matching compatibility Dual Cycle Deselect (DCD) for Pipelined Output Mode 2.5V (±100mV) power supply for core LVTTL compatible, selectable 3.3V (±150mV) or 2.5V (±100mV) power supply for I/Os and control signals on each port Industrial temperature range (-40°C to +85°C) is available at 166MHz and 133MHz Available in a 256-pin Ball Grid Array (BGA), a 208-pin Plastic Quad Flatpack (PQFP) and 208-pin fine pitch Ball Grid Array (fpBGA) Supports JTAG features compliant with IEEE 1149.1 Due to limited pin count JTAG is not supported on the 208pin PQFP package BE3R ◆ ◆ ◆ ◆ ◆ True Dual-Port memory cells which allow simultaneous access of the same memory location High-speed data access – Commercial: 3.4 (200MHz)/3.6ns (166MHz)/ 4.2ns (133MHz)(max.) – Industrial: 3.6ns (166MHz)/4.2ns (133MHz) (max.) Selectable Pipelined or Flow-Through output mode Counter enable and repeat features Dual chip enables allow for depth expansion without additional logic Interrupt and Collision Detection Flags Full synchronous operation on both ports – 5ns cycle time, 200MHz operation (14Gbps bandwidth) – Fast 3.4ns clock to data out – 1.5ns setup to clock and 0.5ns hold on all control, data, and address inputs @ 200MHz BE3L ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ Functional Block Diagram BE2L BE1L BE0L BE2R BE1R BE0R FT/PIPEL 1/0 0a 1a a 0b 1b b 0c 1c c 0d 1d d 1d 0d d 1c 0c c 1b 0b b 1a 0a a 1/0 FT/PIPER R/WL R/WR CE0L CE1L 1 0 1/0 BB BBBB BB W W WWW W WW 01233210 L L L L RR RR 1 0 1/0 CE0R CE1R OEL OER Dout0-8_L Dout9-17_L Dout18-26_L Dout27-35_L Dout0-8_R Dout9-17_R D out18-26_R D out27-35_R 1d 0d 1c 0c 1b 0b 1a 0a 0a 1a 0b 1b 0c 1c 0d 1d 0/1 , FT/PIPER FT/PIPEL 0/1 a bc d dcb a 256/128/64K x 36 MEMORY ARRAY I/O0L - I/O35L Din_L Din_R I/O0R - I/O35R CLKL A17L (1) A0L REPEATL ADSL CNTENL A17R(1) CLKR , Counter/ Address Reg. ADDR_L ADDR_R Counter/ Address Reg. A0R REPEATR ADSR CNTENR TDI TCK TMS TRST CE 0 L CE1 L R /WL INTERRUPT COLLISION DETECTION LOGIC CE0 R CE1 R R/WR JTAG TDO COLR INTR COL L INTL ZZL (2) LOGIC NOTES: 1. Address A17 is a NC for the IDT70T3599. Also, Addresses A17 and A16 are NC's for the IDT70T3589. 2. The sleep mode pin shuts off all dynamic inputs, except JTAG inputs, when asserted. All static inputs, i.e., PL/ FTx and OPTx and the sleep mode pins themselves (ZZx) are not affected during sleep mode. ZZ CONTROL ZZ R (2) 5666 drw 01 APRIL 2004 DSC 5666/6 1 ©2004 Integrated Device Technology, Inc. IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges The IDT70T3519/99/89 is a high-speed 256/128/64K x 36 bit synchronous Dual-Port RAM. The memory array utilizes Dual-Port memory cells to allow simultaneous access of any address from both ports. Registers on control, data, and address inputs provide minimal setup and hold times. The timing latitude provided by this approach allows systems to be designed with very short cycle times. With an input data register, the IDT70T3519/99/89 has been optimized for applications having unidirec- Description: tional or bidirectional data flow in bursts. An automatic power down feature, controlled by CE0 and CE1, permits the on-chip circuitry of each port to enter a very low standby power mode. The 70T3519/99/89 can support an operating voltage of either 3.3V or 2.5V on one or both ports, controllable by the OPT pins. The power supply for the core of the device (VDD) is at 2.5V. 6.42 2 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Configuration (3,4,5,6,9) 70T3519/99/89BC BC-256(7) 256-Pin BGA Top View(8) A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 06/19/02 A1 NC B1 TDI B2 NC B3 A17L(1) A14L B4 B5 A11L B6 A8L B7 BE2L B8 CE1L B9 OEL CNTENL B10 B11 A5L B12 A2L B13 A0L B14 NC B15 NC B16 I/O18L C1 NC C2 TDO C3 NC C4 A15L C5 A12L C6 A9L C7 BE3L C8 CE0L R/WL REPEATL C9 C10 C11 A4L C12 A1L C13 VDD C14 I/O17L C15 NC C16 I/O18R I/O19L D1 D2 VSS A16L(2) D3 D4 A13L D5 A10L D6 A7L D7 BE1L D8 BE0L CLKL ADSL D9 D10 D11 A6L D12 A3L D13 OPTL I/O17R I/O16L D14 D15 D16 I/O20R I/O19R I/O20L PIPE/FTL VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDD I/O15R I/O15L I/O16R E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 E11 E12 E13 E14 E15 E16 I/O21R I/O21L I/O22L VDDQL F1 F2 F3 F4 VDD F5 VDD F6 INTL F7 VSS F8 VSS F9 VSS F10 VDD F11 VDD VDDQR I/O13L I/O14L I/O14R F12 F13 F14 F15 F16 I/O23L I/O22R I/O23R VDDQL G1 G2 G3 G4 VDD G5 NC G6 COLL G7 VSS G8 VSS G9 VSS G10 VSS G11 VDD VDDQR I/O12R I/O13R I/O12L G12 G13 G14 G15 G16 I/O24R I/O24L I/O25L VDDQR H1 H2 H3 H4 VSS H5 VSS H6 VSS H7 VSS H8 VSS H9 VSS H10 VSS H11 VSS H12 VDDQL I/O10L I/O11L I/O11R H13 H14 H15 H16 I/O26L I/O25R I/O26R VDDQR VSS J1 J2 J3 J4 J5 VSS J6 VSS J7 VSS J8 VSS J9 VSS J10 VSS J11 VSS J12 VDDQL I/O9R J13 J14 IO9L I/O10R J15 J16 I/O27L I/O28R I/O27R VDDQL K1 K2 K3 K4 ZZR K5 VSS K6 VSS K7 VSS K8 VSS K9 VSS K10 VSS K11 ZZL K12 VDDQR I/O8R I/O7R K13 K14 K15 I/O8L K16 I/O29R I/O29L I/O28L VDDQL L1 L2 L3 L4 VSS L5 VSS L6 VSS L7 VSS L8 VSS L9 VSS L10 VSS L11 VSS L12 VDDQR I/O6R L13 L14 I/O6L L15 I/O7L L16 I/O30L I/O31R I/O30R VDDQR VDD M1 M2 M3 M4 M5 NC M6 COLR M7 VSS M8 VSS M9 VSS M10 VSS M11 VDD M12 VDDQL I/O5L M13 M14 I/O4R I/O5R M15 M16 I/O32R I/O32L I/O31L VDDQR N1 N2 N3 N4 VDD N5 VDD N6 INTR N7 VSS N8 VSS N9 VSS N10 VDD N11 VDD N12 VDDQL I/O3R N13 N14 I/O3L N15 I/O4L N16 I/O33L I/O34R I/O33R PIPE/FTR VDDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 VDD P13 I/O2L P14 I/O1R I/O2R P15 P16 I/O35R I/O34L TMS A16R(2) A13R R1 R2 R3 R4 R5 A10R R6 A7R R7 BE1R BE0R CLKR ADSR R8 R9 R10 R11 A6R R12 A3R R13 I/O0L I/O0R R14 R15 I/O1L R16 I/O35L T1 NC T2 TRST T3 NC T4 A15R T5 A12R T6 A9R T7 BE3R CE0R R/WR REPEATR T8 T9 T10 T11 A4R T12 A1R T13 OPTR T14 NC T15 NC T16 , NC TCK NC A17R(1) A14R A11R A8R BE2R CE1R OER CNTENR A5R A2R A0R NC NC NOTES: 1. Pin is a NC for IDT70T3599 and IDT70T3589. 2. Pin is a NC for IDT70T3589. 3. All VDD pins must be connected to 2.5V power supply. 4. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V), and 2.5V if OPT pin for that port is set to VSS (0V). 5. All VSS pins must be connected to ground supply. 6. Package body is approximately 17mm x 17mm x 1.4mm, with 1.0mm ball-pitch. 7. This package code is used to reference the package diagram. 8. This text does not indicate orientation of the actual part-marking. 9. Pins A15 and T15 will be VREFL and VREFR respectively for future HSTL device. 5666 drw 02d , 6.42 3 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Configuration (3,4,5,6,9,10) (con't.) VSS VDDQR I/O18R I/O18L VSS PL/FTL COLL INTL NC NC A17L(1) A16L(2) A15L A14L A13L A12L A11L A10L A9L A8L A7L BE3L BE2L BE1L BE0L CE1L CE0L VDD VDD VSS VSS CLKL OEL R/WL ADSL CNTENL REPEATL A6L A5L A4L A3L A2L A1L A0L VDD VDD NC OPTL I/O17L I/O17R VDDQR VSS 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 06/19/02 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 I/O19L I/O19R I/O20L I/O20R VDDQL VSS I/O21L I/O21R I/O22L I/O22R VDDQR VSS I/O23L I/O23R I/O24L I/O24R VDDQL VSS I/O25L I/O25R I/O26L I/O26R VDDQR ZZR VDD VDD VSS VSS VDDQL VSS I/O27R I/O27L I/O28R I/O28L VDDQR VSS I/O29R I/O29L I/O30R I/O30L VDDQL VSS I/O31R I/O31L I/O32R I/O32L VDDQR VSS I/O33R I/O33L I/O34R I/O34L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 70T3519/99/89DR DR-208(7) 208-Pin PQFP Top View(8) 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 I/O16L I/O16R I/O15L I/O15R VSS VDDQL I/O14L I/O14R I/O13L I/O13R VSS VDDQR I/O12L I/O12R I/O11L I/O11R VSS VDDQL I/O10L I/O10R I/O9L I/O9R VSS VDDQR VDD VDD VSS VSS ZZL VDDQL I/O8R I/O8L I/O7R I/O7L VSS VDDQR I/O6R I/O6L I/O5R I/O5L VSS VDDQL I/O4R I/O4L I/O3R I/O3L VSS VDDQR I/O2R I/O2L I/O1R I/O1L , NOTES: 1. Pin is a NC for IDT70T3599 and IDT70T3589. 2. Pin is a NC for IDT70T3589. 3. All VDD pins must be connected to 2.5V power supply. 4. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V), and 2.5V if OPT pin for that port is set to V ss (0V). 5. All VSS pins must be connected to ground supply. 6. Package body is approximately 28mm x 28mm x 3.5mm. 7. This package code is used to reference the package diagram. 8. This text does not indicate orientation of the actual part-marking. 9. Due to limited pin count, JTAG is not supported in the DR-208 package. 10. Pins 162 and 99 will be VREFL and VREFR respectively for future HSTL device. VSS VDDQL I/O35R I/O35L PL/FTR NC COLR INTR NC NC A17R(1) A16R(2) A15R A14R A13R A12R A11R A10R A9R A8R A7R BE3R BE2R BE1R BE0R CE1R CE0R VDD VDD VSS VSS CLKR OER R/WR ADSR CNTENR REPEATR A6R A5R A4R A3R A2R A1R A0R VDD VSS NC OPTR I/O0L I/O0R VDDQL VSS 5666 drw 02a 6.42 4 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Configuration (3,4,5,6,9) (con't.) 01/23/03 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 I/O19L I/O18L B1 B2 V SS B3 TDO B4 COLL A16L(2) A12L B5 B6 B7 A8L B8 BE1L B9 VDD B10 CLKL CNTENL A4L B11 B12 B13 A 0L B14 OPTL I/O17L B15 B16 V SS B17 I/O20R C1 V SS I/O18R C2 C3 TDI C4 A17L(1) A 13L C5 C6 A9L C7 BE2L C8 CE0L C9 VSS C10 ADSL C11 A5L C12 A1L C13 NC C14 VDDQR I/O16L I/O15R C15 C16 C17 VDDQL I/O19R VDDQR PL/FTL INT L D1 D2 D3 D4 D5 A 14L D6 A10L D7 BE 3L CE1L D8 D9 V SS D10 R/WL D 11 A6L D12 A2L D13 VDD I/O16R I/O15L D14 D15 D16 VSS D17 I/O22L E1 V SS E2 I/O21L I/O20L A15L E3 E4 A 11L A7L BE0L VDD OEL REPEATL A3L VDD I/O17R VDDQL I/O14L I/O14R E14 E15 E16 E17 I/O23L I/O22R VDDQR I/O21R F1 F2 F3 F4 I/O12L I/O13R F14 F15 VSS F16 I/O13L F17 VDDQL I/O23R I/O24L G1 G2 G3 VSS G4 VSS G14 I/O12R I/O11L VDDQR G15 G16 G17 I/O26L V SS H1 H2 I/O25L I/O24R H3 H4 I/O9L VDDQL I/O10L I/O11R VDD I/O26R VDDQR I/O25R J1 J2 J3 J4 70T3519/99/89BF BF-208(7) 208-Pin fpBGA Top View(8) H14 H15 H16 H17 VDD J14 I/O9R J15 V SS J16 I/O10R J17 VDDQL VDD K1 K2 VSS K3 ZZR K4 ZZL K14 VDD K15 VSS VDDQR K16 K17 I/O28R L1 VSS L2 I/O27R L3 VSS L4 I/O7R VDDQL I/O8R L14 L15 L16 V SS L17 I/O29R I/O28L VDDQR I/O27L M1 M2 M3 M4 I/O6R M14 I/O7L M15 V SS M16 I/O8L M17 VDDQL I/O29L I/O30R VSS N1 N2 N3 N4 VSS N14 I/O6L I/O5R VDDQR N15 N16 N17 I/O31L V SS I/O31R I/O30L P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 I/O3R VDDQL I/O4R P14 P15 P16 I/O5L P17 I/O32R I/O32L VDDQR I/O35R TRST A16R(2) A12R R1 R2 R3 R4 R5 R6 R7 A8R R8 BE1R R9 VDD R10 CLKR C NTEN R A 4R R11 R12 R13 I/O2L I/O3L R14 R15 VSS R16 I/O4L R17 VSS T1 I/O33L I/O34R TCK A17R(1) A13R T2 T3 T4 T5 T6 A9R T7 BE 2R CE0R T8 T9 VSS T10 ADS R T11 A5R T12 A1R T13 NC T14 V DDQL I/O1R VDDQR T15 T16 T17 I/O33R I/O34L VDDQL TMS U1 U2 U3 U4 INTR U5 A14R U6 A10R U7 BE3R CE1R U8 U9 V SS U10 R/W R A6R U12 A2R U13 VSS U14 I/O0R U15 VSS U16 I/O2R U17 VSS I/O35L PL/FTR COLR A15R A11R A7R BE0R VDD OER A3R A 0R VDD OPTR I/O0L I/O1L 5666 drw 02c NOTES: 1. Pin is a NC for IDT70T3599 and IDT70T3589. 2. Pin is a NC for IDT70T3589. 3. All VDD pins must be connected to 2.5V power supply. 4. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V), and 2.5V if OPT pin for that port is set to V SS (0V). 5. All VSS pins must be connected to ground supply. 6. Package body is approximately 15mm x 15mm x 1.4mm with 0.8mm ball pitch. 7. This package code is used to reference the package diagram. 8. This text does not indicate orientation of the actual part-marking. 9. Pins B14 and R14 will be V REFL and VREFR respectively for future HSTL device. 6.42 5 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Names Left Port CE0L, CE1L R/WL OEL A0L - A17L(6) I/O0L - I/O35L CLKL PL/FTL ADSL CNTENL REPEATL BE0L - BE3L VDDQL OPTL ZZL VDD VSS TDI(5) TDO(5) TCK (5) (5) (5) Right Port CE0R, CE1R R/WR OER A0R - A17R(6) I/O0R - I/O35R CLKR PL/FTR ADSR CNTENR REPEATR BE0R - BE3R VDDQR OPTR ZZR Names Chip Enables (Input)(7) Read/Write Enable (Input) Output Enable (Input) Address (Input) Data Input/Output Clock (Input) Pipeline/Flow-Through (Input) Address Strobe Enable (Input) Counter Enable (Input) Counter Repeat(3) Byte Enables (9-bit bytes) (Input)(7) Power (I/O Bus) (3.3V or 2.5V)(1) (Input) Option for selecting V DDQX(1,2) (Input) Sleep Mode pin(4) (Input) Power (2.5V)(1) (Input) Ground (0V) (Input) Test Data Input Test Data Output Test Logic Clock (10MHz) (Input) Test Mode Select (Input) Reset (Initialize TAP Controller) (Input) TMS TRST INTL COLL INTR COLR Interrupt Flag (Output) Collision Alert (Output) 5666 tbl 01 NOTES: 1. VDD, OPTX, and VDDQX must be set to appropriate operating levels prior to applying inputs on the I/Os and controls for that port. 2. OPTX selects the operating voltage levels for the I/Os and controls on that port. If OPTX is set to VDD (2.5V), then that port's I/Os and controls will operate at 3.3V levels and VDDQX must be supplied at 3.3V. If OPT X is set to VSS (0V), then that port's I/Os and address controls will operate at 2.5V levels and VDDQX must be supplied at 2.5V. The OPT pins are independent of one another—both ports can operate at 3.3V levels, both can operate at 2.5V levels, or either can operate at 3.3V with the other at 2.5V. 3. When REPEATX is asserted, the counter will reset to the last valid address loaded via ADS X. 4. The sleep mode pin shuts off all dynamic inputs, except JTAG inputs, when asserted. All static inputs, i.e., PL/FTx and OPTx and the sleep mode pins themselves (ZZx) are not affected during sleep mode. It is recommended that boundry scan not be operated during sleep mode. 5. Due to limited pin count, JTAG is not supported in the DR-208 package. 6. Address A17x is a NC for the IDT70T3599. Also, Addresses A17x and A16x are NC's for the IDT 70T3589. 7. Chip Enables and Byte Enables are double buffered when PL/FT = VIH, i.e., the signals take two cycles to deselect. 6.42 6 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Truth Table I—Read/Write and Enable Control OE X X X X X X X X X X L L L L L L L H X CLK ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ X CE0 H X L L L L L L L L L L L L L L L X X CE1 X L H H H H H H H H H H H H H H H X X BE3 X X H H H H L H L L H H H L H L L X X BE2 X X H H H L H H L L H H L H H L L X X BE1 X X H H L H H L H L H L H H L H L X X BE0 X X H L H H H L H L L H H H L H L X X R/ W X X X L L L L L L L H H H H H H H X X ZZ L L L L L L L L L L L L L L L L L L H Byte 3 I/O27-35 High-Z High-Z High-Z High-Z High-Z High-Z DIN High-Z DIN DIN High-Z High-Z High-Z DOUT High-Z DOUT DOUT High-Z High-Z Byte 2 I/O18-26 High-Z High-Z High-Z High-Z High-Z DIN High-Z High-Z DIN DIN High-Z High-Z DOUT High-Z High-Z DOUT DOUT High-Z High-Z (1,2,3,4) Byte 1 I/O9-17 High-Z High-Z High-Z High-Z DIN High-Z High-Z DIN High-Z DIN High-Z DOUT High-Z High-Z DOUT High-Z DOUT High-Z High-Z Byte 0 I/O0-8 High-Z High-Z High-Z DIN High-Z High-Z High-Z DIN High-Z DIN DOUT High-Z High-Z High-Z DOUT High-Z DOUT High-Z High-Z MODE Deselected–Power Down Deselected–Power Down All Bytes Deselected Write to Byte 0 Only Write to Byte 1 Only Write to Byte 2 Only Write to Byte 3 Only Write to Lower 2 Bytes Only Write to Upper 2 bytes Only Write to All Bytes Read Byte 0 Only Read Byte 1 Only Read Byte 2 Only Read Byte 3 Only Read Lower 2 Bytes Only Read Upper 2 Bytes Only Read All Bytes Outputs Disabled Sleep Mode 5666 tbl 02 NOTES: 1. "H" = V IH, "L" = VIL, "X" = Don't Care. 2. ADS , CNTEN, REPEAT = VIH. 3. OE and ZZ are asynchronous input signals. 4. It is possible to read or write any combination of bytes during a given access. A few representative samples have been illustrated here. Truth Table II—Address Counter Control Address An X X X Previous Internal Address X An An + 1 X Internal Address Used An An + 1 An + 1 An CLK ↑ ↑ ↑ ↑ ADS L(4) H H X CNTEN X L (5) (1,2) REPEAT(6) H H H L(4) I/O(3) DI/O (n) DI/O(n+1) DI/O(n+1) DI/O(n) External Address Used MODE Counter Enabled—Internal Address generation External Address Blocked—Counter disab led (An + 1 reused) Counter Set to last valid ADS load 5666 tbl 03 H X NOTES: 1. "H" = V IH, "L" = VIL, "X" = Don't Care. 2. Read and write operations are controlled by the appropriate setting of R/ W, CE 0, CE1, BEn and OE. 3. Outputs configured in flow-through output mode: if outputs are in pipelined mode the data out will be delayed by one cycle. 4. ADS and REPEAT are independent of all other memory control signals including CE0, CE1 and BEn 5. The address counter advances if CNTEN = VIL on the rising edge of CLK, regardless of all other memory control signals including CE0, CE1, BEn. 6. When REPEAT is asserted, the counter will reset to the last valid address loaded via ADS. This value is not set at power-up: a known location should be loaded via ADS during initialization if desired. Any subsequent ADS access during operations will update the REPEAT address location. 6.42 7 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Recommended Operating Temperature and Supply Voltage Grade Commercial Industrial Ambient Temperature 0 C to +70 C O O (1) GND 0V 0V VDD 2.5V + 100mV 2.5V + 100mV 5666 tbl 04 -40OC to +85OC NOTES: 1. This is the parameter TA. This is the "instant on" case temperature. Recommended DC Operating Conditions with VDDQ at 2.5V Symbol V DD V DDQ V SS V IH Parameter Core Supply Voltage I/O Supply Voltage (3) Ground Input High Volltage (Address, Control & Data I/O Inputs)(3) Input High Voltage JTAG _ Min. 2.4 2.4 0 1.7 Typ. 2.5 2.5 0 ____ Max. 2.6 2.6 0 VDDQ + 100mV (2) Unit V V V V V IH V IH VIL VIL 1.7 V DD - 0.2V -0.3(1) -0.3(1) ____ VDD + 100mV (2) VDD + 100mV (2) 0.7 0.2 V V V V 5666 tbl 05a Input High Voltage ZZ, OPT, PIPE/ FT Input Low Voltage Input Low Voltage ZZ, OPT, PIPE/ FT ____ ____ ____ NOTES: 1. VIL (min.) = -1.0V for pulse width less than tCYC /2 or 5ns, whichever is less. 2. VIH (max.) = VDDQ + 1.0V for pulse width less than tCYC /2 or 5ns, whichever is less. 3. To select operation at 2.5V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to Vss(0V), and V DDQX for that port must be supplied as indicated above. Recommended DC Operating Conditions with VDDQ at 3.3V Symbol VDD VDDQ VSS VIH Parameter Core Supply Voltage I/O Supply Voltage Ground Input High Voltage (Address, Control &Data I/O Inputs)(3) Input High Voltage JTAG _ (3) Min. 2.4 3.15 0 2.0 Typ. 2.5 3.3 0 ____ Max. 2.6 3.45 0 VDDQ + 150mV(2) Unit V V V V VIH VIH VIL VIL 1.7 VDD - 0.2V -0.3 (1) ____ VDD + 100mV(2) VDD + 100mV(2) 0.8 0.2 V V V V Input High Voltage ZZ, OPT, PIPE/ FT Input Low Voltage Input Low Voltage ZZ, OPT, PIPE/ FT ____ ____ -0.3(1) ____ NOTES: 1. VIL (min.) = -1.0V for pulse width less than tCYC/2, or 5ns, whichever is less. 2. VIH (max.) = V DDQ + 1.0V for pulse width less than tCYC /2 or 5ns, whichever is less. 3. To select operation at 3.3V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to VDD (2.5V), and VDDQX for that port must be supplied as indicated above. 5666 tbl 05b 6.42 8 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Absolute Maximum Ratings (1) Symbol VTERM (VDD) VTERM(2) (VDDQ ) VTERM(2) (INPUTS and I/O's) TBIAS(3) TSTG TJN Rating VDD Terminal Voltage with Respect to GND VDDQ Terminal Voltage with Respect to GND Input and I/O Terminal Voltage with Respect to GND Temperature Under Bias Storage Temperature Junction Temperature Commercial & Industrial -0.5 to 3.6 -0.3 to VDDQ + 0.3 -0.3 to VDDQ + 0.3 -55 to +125 -65 to +150 +150 50 40 Unit V V V o o o C C C IOUT(For VDDQ = 3.3V) DC Output Current IOUT(For VDDQ = 2.5V) DC Output Current mA mA 5666 tbl 06 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. This is a steady-state DC parameter that applies after the power supply has reached its nominal operating value. Power sequencing is not necessary; however, the voltage on any Input or I/O pin cannot exceed VDDQ during power supply ramp up. 3. Ambient Temperature under DC Bias. No AC Conditions. Chip Deselected. Capacitance (1) Symbol CIN COUT(3) Parameter Input Capacitance (TA = +25°C, F = 1.0MHZ) PQFP ONLY Conditions(2) VIN = 3dV VOUT = 3dV Max. 8 10.5 Unit pF pF 5666 tbl 07 Output Capacitance NOTES: 1. These parameters are determined by device characterization, but are not production tested. 2. 3dV references the interpolated capacitance when the input and output switch from 0V to 3V or from 3V to 0V. 3. COUT also references CI/O. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 2.5V ± 100mV) 70T3519/99/89S Symbol |ILI| |ILI| |ILO| VOL (3.3V) VOH (3.3V) VOL (2.5V) VOH (2.5V) Parameter Input Leakage Current(1) JTAG & ZZ Input Leakage Current Output Leakage Current Output Low Voltage (1) (1) (1,3) (1,2) Test Conditions VDDQ = Max., VIN = 0V to VDDQ VDD = Max., V IN = 0V to VDD CE0 = VIH or CE1 = VIL, VOUT = 0V to VDDQ IOL = + 4mA, VDDQ = Min. IOH = -4mA, V DDQ = Min. IOL = + 2mA, VDDQ = Min. IOH = -2mA, V DDQ = Min. Min. ___ ___ ___ ___ Max. 10 ±30 10 0.4 ___ Unit µA µA µA V V V V 5666 tbl 08 Output High Voltage 2.4 ___ Output Low Voltage (1) Output High Voltage (1) 0.4 ___ 2.0 NOTES: 1. VDDQ is selectable (3.3V/2.5V) via OPT pins. Refer to p.5 for details. 2. Applicable only for TMS, TDI and TRST inputs. 3. Outputs tested in tri-state mode. 6.42 9 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (3) (VDD = 2.5V ± 100mV) 70T3519/99/89 S200 Com'l Only(8) Symbol IDD Parameter Dynamic Operating Current (Both Ports Active) Standby Current (Both Ports - TTL Level Inputs) Standby Current (One Port - TTL Level Inputs) Full Standby Current (Both Ports - CMOS Level Inputs) Full Standby Current (One Port - CMOS Level Inputs) Sleep Mode Current (Both Ports - TTL Level Inputs) CEL and CER= VIL, Outputs Disabled, f = fMAX(1) CEL = CER = VIH f = fMAX(1) CE"A" = VIL and CE"B" = VIH(5) Active Port Outputs Disabled, f=fMAX(1) Both Ports CEL and CER > VDDQ - 0.2V, VIN > VDDQ - 0.2V or VIN < 0.2V, f = 0(2) CE"A" < 0.2V and CE"B" > VDDQ - 0.2V(5) VIN > VDDQ - 0.2V or VIN < 0.2V Active Port, Outputs Disabled, f = fMAX(1) ZZL = ZZR = VIH f=fMAX(1) Test Condition Version COM'L IND COM'L IND COM'L IND COM'L IND COM'L IND COM'L IND S S S S S S S S S S S S Typ.(4) 375 ___ 70T3519/99/89 S166 Com'l & Ind(7) Typ.(4) 320 320 175 175 250 250 5 5 250 250 5 5 Max. 450 510 230 275 325 365 15 20 325 365 15 20 70T3519/99/89 S133 Com'l & Ind Typ.(4) 260 260 140 140 200 200 5 5 200 200 5 5 Max. 370 450 190 235 250 310 15 20 250 310 15 20 mA Unit mA Max. 525 ___ ISB1(6) 205 ___ 270 ___ mA ISB2(6) 300 ___ 375 ___ mA ISB3 5 ___ 15 ___ ISB4(6) 300 ___ 375 ___ mA Izz 5 ___ 15 ___ mA 5666 tbl 09 NOTES: 1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency clock cycle of 1/tCYC , using "AC TEST CONDITIONS". 2. f = 0 means no address, clock, or control lines change. Applies only to input at CMOS level standby. 3. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 4. VDD = 2.5V, TA = 25°C for Typ, and are not production tested. I DD DC(f=0) = 15mA (Typ). 5. CEX = VIL means CE0X = VIL and CE1X = VIH CEX = VIH means CE0X = VIH or CE1X = V IL CEX < 0.2V means CE0X < 0.2V and CE1X > VDD - 0.2V CEX > VDD - 0.2V means CE0X > VDD - 0.2V or CE1X - 0.2V "X" represents "L" for left port or "R" for right port. 6. ISB1, I SB2 and ISB4 will all reach full standby levels (ISB3) on the appropriate port(s) if ZZL and/or ZZR = VIH. 7. 166MHz I-Temp is not available in the BF-208 package. 8. 200Mhz is not available in the BF-208 and DR-208 packages. 6.42 10 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges AC Test Conditions (VDDQ - 3.3V/2.5V) Input Pulse Levels (Address & Controls) Input Pulse Levels (I/Os) Input Rise/Fall Times Input Timing Reference Levels Output Reference Levels Output Load GND to 3.0V/GND to 2.4V GND to 3.0V/GND to 2.4V 2ns 1.5V/1.25V 1.5V/1.25V Figure 1 5666 tbl 10 50Ω DATAOUT 50Ω 1.5V/1.25 10pF (Tester) , 5666 drw 03 Figure 1. AC Output Test load. ∆ tCD (Typical, ns) ∆ Capacitance (pF) from AC Test Load 5666 drw 04 6.42 11 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature Range (Read and Write Cycle Timing) (2,3) (VDD = 2.5V ± 100mV, TA = 0°C to +70°C) 70T3519/99/89 S200 Com'l Only(5) Symbol tCYC1 tCYC2 tCH1 tCL1 tCH2 tCL2 tSA tHA tSC tHC tSB tHB tSW tHW tSD tHD tSAD tHAD tSCN tHCN tSRPT tHRPT tOE tOLZ(6) tOHZ(6) tCD1 tCD2 tDC tCKHZ(6) tCKLZ(6) tINS tINR tCOLS tCOLR tZZSC tZZRC Clock Cycle Time (Flow-Through)(1) Clock Cycle Time (Pipelined)(1) Clock High Time (Flow-Through) (1) 70T3519/99/89 S166 Com'l & Ind(4) Min. 20 6 8 8 2.4 2.4 1.7 0.5 1.7 0.5 1.7 0.5 1.7 0.5 1.7 0.5 1.7 0.5 1.7 0.5 1.7 0.5 ____ 70T3519/99/89 S133 Com'l & Ind Min. 25 7.5 10 10 3 3 1.8 0.5 1.8 0.5 1.8 0.5 1.8 0.5 1.8 0.5 1.8 0.5 1.8 0.5 1.8 0.5 ____ Parameter Min. 15 5 6 6 2 2 1.5 0.5 1.5 0.5 1.5 0.5 1.5 0.5 1.5 0.5 1.5 0.5 1.5 0.5 1.5 0.5 ____ Max. ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ Max. ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ Max. ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns cycles cycles Clock Low Time (Flow-Through)(1) Clock High Time (Pipelined)(2) Clock Low Time (Pipelined)(1) Address Setup Time Address Hold Time Chip Enable Setup Time Chip Enable Hold Time Byte Enable Setup Time Byte Enable Hold Time R/W Setup Time R/W Hold Time Input Data Setup Time Input Data Hold Time ADS Setup Time ADS Hold Time CNTEN Setup Time CNTEN Hold Time REPEAT S etup Time REPEAT Hold Time Output Enable to Data Valid Output Enable to Output Low-Z Output Enable to Output High-Z Clock to Data Valid (Flow-Through)(1) Clock to Data Valid (Pipelined) (1) 4.4 ____ 4.4 ____ 4.6 ____ 1 1 ____ ____ 1 1 ____ ____ 1 1 ____ ____ 3.4 10 3.4 ____ 3.6 12 3.6 ____ 4.2 15 4.2 ____ Data Output Hold After Clock High Clock High to Output High-Z Clock High to Output Low-Z Interrupt Flag Set Time Interrupt Flag Reset Time Collision Flag Set Time Collision Flag Reset Time Sleep Mode Set Cycles Sleep Mode Recovery Cycles 1 1 1 ____ ____ ____ ____ 1 1 1 ____ ____ ____ ____ 1 1 1 ____ ____ ____ ____ 3.4 ____ 3.6 ____ 4.2 ____ 7 7 3.4 3.4 ____ ____ 7 7 3.6 3.6 ____ ____ 7 7 4.2 4.2 ____ ____ 2 3 2 3 2 3 Port-to-Port Delay tCO tOFS Clock-to-Clock Offset Clock-to-Clock Offset for Collision Detection 4 ____ 5 ____ 6 ____ ns Please refer to Collision Detection Timing Table on Page 21 5666 tbl 11 NOTES: 1. The Pipelined output parameters (tCYC2, tCD2) apply to either or both left and right ports when FT/PIPEX = VDD (2.5V). Flow-through parameters (tCYC1, tCD1) apply when FT/PIPE = Vss (0V) for that port. 2. All input signals are synchronous with respect to the clock except for the asynchronous Output Enable (OE), FT/PIPE and OPT. FT/PIPE and OPT should be treated as DC signals, i.e. steady state during operation. 3. These values are valid for either level of VDDQ (3.3V/2.5V). See page 6 for details on selecting the desired operating voltage levels for each port. 4. 166MHz I-Temp is not available in the BF-208 package. 5. 200Mhz is not available in the BF-208 and DR-208 packages. 6. Guaranteed by design (not production tested). 6.42 12 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Read Cycle for Pipelined Operation (FT/PIPE'X' = VIH)(1,2) tCYC2 tCH2 CLK CE0 tCL2 tSC CE1 tSB BEn tHC tSC (3) tHC tHB tSB (5) tHB R/W tSW tSA tHW tHA An + 1 (1 Latency) tCD2 Qn tCKLZ (1) ADDRESS (4) An An + 2 tDC Qn + 1 An + 3 DATAOUT Qn + 2 tOLZ (5) tOHZ OE (1) tOE 5666 drw 05 Timing Waveform of Read Cycle for Flow-through Output (FT/PIPE"X" = VIL)(1,2,6) tCYC1 tCH1 CLK CE0 tCL1 tSC CE1 tSB BEn tHC tSC (3) tHC tHB tSB tHB R/W tSW tHW tSA tHA An + 1 tCD1 tDC Qn tCKLZ (1) ADDRESS (4) An An + 2 An + 3 tCKHZ DATAOUT Qn + 1 tOHZ tOLZ Qn + 2 (5) tDC OE NOTES: 1. OE is asynchronously controlled; all other inputs depicted in the above waveforms are synchronous to the rising clock edge. 2. ADS = VIL, CNTEN and REPEAT = VIH. 3. The output is disabled (High-Impedance state) by CE0 = VIH, CE1 = VIL, BEn = VIH following the next rising edge of the clock. Refer to Truth Table 1. 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. If BEn was HIGH, then the appropriate Byte of DATA OUT for Qn + 2 would be disabled (High-Impedance state). 6. "x" denotes Left or Right port. The diagram is with respect to that port. tOE 5666 drw 06 6.42 13 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of a Multi-Device Pipelined Read tCH2 CLK tSA ADDRESS(B1) tSC CE0(B1) (1,2) tCYC2 tCL2 tHA A0 tHC tSC tCD2 tHC tCD2 Q0 tDC Q1 tDC A3 A4 tCKLZ A5 tCKHZ tCD2 Q3 tCKHZ A6 A1 A2 A3 A4 A5 A6 DATAOUT(B1) tSA ADDRESS(B2) tHA A0 A1 A2 tSC CE0(B2) tHC tSC tHC tCD2 tCKHZ Q2 tCKLZ tCKLZ 5666 drw 07 tCD2 Q4 DATAOUT(B2) Timing Waveform of a Multi-Device Flow-Through Read tCH1 CLK tSA ADDRESS(B1) tHA A0 tSC tHC tSC tHC tCD1 DATAOUT(B1) tSA ADDRESS(B2) tHA A0 A1 A2 A3 A4 D0 tDC tCD1 D1 tDC tCKLZ (1) (1,2) tCYC1 tCL1 A1 A2 A3 A4 A5 A6 CE0(B1) tCKHZ (1) tCD1 D3 tCKHZ (1) tCD1 D5 tCKLZ A5 (1) A6 tSC tHC CE0(B2) tSC tHC tCD1 DATAOUT(B2) tCKLZ (1) tCKHZ D2 (1) tCD1 tCKLZ (1) tCKHZ D4 (1) 5666 drw 08 NOTES: 1. B1 Represents Device #1; B2 Represents Device #2. Each Device consists of one IDT70T3519/99/89 for this waveform, and are setup for depth expansion in this example. ADDRESS(B1) = ADDRESS(B2) in this situation. 2. BEn, OE, and ADS = VIL; CE1(B1) , CE1(B2) , R/W, CNTEN, and REPEAT = VIH. 6.42 14 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Left Port Write to Pipelined Right Port Read CLK"A" tSW R/W"A" tSA ADDRESS"A" tHA NO MATCH (1,2,4) tHW MATCH tSD DATAIN"A" tHD VALID tCO(3) CLK"B" tCD2 R/W"B" tSW tSA ADDRESS"B" tHW tHA NO MATCH MATCH DATAOUT"B" VALID NOTES: 1. CE0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 2. OE = VIL for Port "B", which is being read from. OE = VIH for Port "A", which is being written to. 3. If tCO < minimum specified, then data from Port "B" read is not valid until following Port "B" clock cycle (ie, time from write to valid read on opposite port will be tCO + 2 tCYC2 + tCD2 ). If tCO > minimum, then data from Port "B" read is available on first Port "B" clock cycle (ie, time from write to valid read on opposite port will be tCO + t CYC2 + t CD2). 4. All timing is the same for Left and Right ports. Port "A" may be either Left or Right port. Port "B" is the opposite of Port "A" tDC 5666 drw 09 Timing Waveform with Port-to-Port Flow-Through Read CLK "A" tSW R/W "A" tSA ADDRESS "A" tHA NO MATCH (1,2,4) tHW MATCH tSD DATAIN "A" tHD VALID tCO CLK "B" (3) tCD1 R/W "B" tSW tSA ADDRESS "B" tHW tHA NO MATCH MATCH tCD1 DATAOUT "B" tDC VALID VALID tDC 5666 drw 10 NOTES: 1. CE0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 2. OE = VIL for the Right Port, which is being read from. OE = VIH for the Left Port, which is being written to. 3. If tCO < minimum specified, then data from Port "B" read is not valid until following Port "B" clock cycle (i.e., time from write to valid read on opposite port will be tCO + tCYC + tCD1). If tCO > minimum, then data from Port "B" read is available on first Port "B" clock cycle (i.e., time from write to valid read on opposite port will be tCO + t CD1). 4. All timing is the same for both left and right ports. Port "A" may be either left or right port. Port "B" is the opposite of Port "A". 6.42 15 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Pipelined Read-to-Write-to-Read tCYC2 (OE = VIL)(2) tCH2 tCL2 CLK CE0 tSC CE1 tSB BEn tHC tHB tSW tHW R/W tSW tHW ADDRESS (3) An tSA tHA An +1 An + 2 An + 2 tSD tHD Dn + 2 An + 3 An + 4 DATAIN (1) tCD2 Qn tCKHZ tCKLZ tCD2 Qn + 3 DATAOUT READ NOP (4) WRITE READ 5666 drw 11 NOTES: 1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 2. CE 0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. "NOP" is "No Operation". 3. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 4. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity. Timing Waveform of Pipelined Read-to-Write-to-Read ( OE Controlled) (2) tCH2 CLK CE0 tCYC2 tCL2 tSC CE1 tSB BEn tHC tHB tSW tHW R/W tSW tHW (3) ADDRESS An tSA tHA An +1 An + 2 tSD tHD An + 3 An + 4 An + 5 DATAIN (1) tCD2 Qn tOHZ (4) Dn + 2 Dn + 3 tCKLZ tCD2 Qn + 4 DATAOUT OE 5666 drw 12 NOTES: 1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 2. CE0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 3. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 4. This timing does not meet requirements for fastest speed grade. This waveform indicates how logically it could be done if timing so allows. READ WRITE READ 6.42 16 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Flow-Through Read-to-Write-to-Read ( OE = VIL)(2) tCH1 CLK tCYC1 tCL1 CE0 tSC CE1 tSB BEn tHC tHB tSW tHW R/W tSW tHW ADDRESS (3) tSA DATAIN (1) An tHA An +1 An + 2 An + 2 tSD tHD Dn + 2 An + 3 An + 4 tCD1 Qn tDC READ tCD1 Qn + 1 tCKHZ (5) NOP tCD1 tCD1 Qn + 3 tDC READ DATAOUT tCKLZ WRITE 5666 drw 13 Timing Waveform of Flow-Through Read-to-Write-to-Read (OE Controlled)(2) tCYC1 tCH1 tCL1 CLK CE0 tSC tHC CE1 tSB BEn tHB tSW tHW R/W ADDRESS (3) tSW tHW An tSA tHA An +1 An + 2 tSD tHD Dn + 2 (1) An + 3 An + 4 An + 5 DATAIN tCD1 Qn tOHZ OE Dn + 3 tDC tOE tCD1 tCKLZ tCD1 Qn + 4 tDC DATAOUT READ WRITE READ 5666 drw 14 NOTES: 1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 2. CE 0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 3. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 4. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity. 6.42 17 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Pipelined Read with Address Counter Advance tCH2 CLK tSA ADDRESS tHA tCYC2 tCL2 (1) An tSAD tHAD ADS tSAD tHAD CNTEN tSCN tHCN tCD2 DATAOUT Qx - 1(2) Qx tDC Qn Qn + 1 Qn + 2(2) Qn + 3 READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD READ WITH COUNTER 5666 drw 15 Timing Waveform of Flow-Through Read with Address Counter Advance tCH1 CLK tSA ADDRESS tHA tCYC1 tCL1 (1) An tSAD tHAD ADS tSAD tHAD tSCN tHCN CNTEN tCD1 DATAOUT Qx(2) tDC READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD READ WITH COUNTER 5666 drw 16 Qn Qn + 1 Qn + 2 Qn + 3(2) Qn + 4 NOTES: 1. CE0, OE, BEn = VIL; CE1, R/W, and REPEAT = V IH. 2. If there is no address change via ADS = V IL (loading a new address) or CNTEN = VIL (advancing the address), i.e. ADS = VIH and CNTEN = VIH, then the data output remains constant for subsequent clocks. 6.42 18 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Write with Address Counter Advance (Flow-through or Pipelined Inputs) (1) tCH2 CLK tSA ADDRESS tHA tCYC2 tCL2 An INTERNAL(3) ADDRESS tSAD tHAD ADS An(7) An + 1 An + 2 An + 3 An + 4 tSCN tHCN CNTEN tSD tHD DATAIN Dn WRITE EXTERNAL ADDRESS Dn + 1 Dn + 1 Dn + 2 Dn + 3 Dn + 4 WRITE WRITE WITH COUNTER COUNTER HOLD WRITE WITH COUNTER 5666 drw 17 Timing Waveform of Counter Repeat tCYC2 CLK tSA tHA ADDRESS INTERNAL ADDRESS (3) (2,6) An An tSAD tHAD An+1 An+2 An+2 An An+1 An+2 An+2 ADS tSW tHW R/W tSCN tHCN CNTEN (4) REPEAT tSRPT tHRPT tSD tHD DATAIN D0 D1 D2 D3 tCD1 DATAOUT WRITE TO ADS ADDRESS An ADVANCE COUNTER WRITE TO An+1 ADVANCE COUNTER WRITE TO An+2 HOLD COUNTER WRITE TO An+2 An REPEAT READ LAST ADS ADDRESS An An+1 ADVANCE COUNTER READ An+1 An+2 , An+2 HOLD COUNTER READ An+2 5666 drw 18 ADVANCE COUNTER READ An+2 NOTES: 1. CE 0, BEn, and R/W = VIL; CE1 and REPEAT = VIH. 2. CE 0, BEn = VIL; CE1 = VIH. 3. The "Internal Address" is equal to the "External Address" when ADS = VIL and equals the counter output when ADS = VIH. 4. No dead cycle exists during REPEAT operation. A READ or WRITE cycle may be coincidental with the counter REPEAT cycle: Address loaded by last valid ADS load will be accessed. For more information on REPEAT function refer to Truth Table II. 5. CNTEN = VIL advances Internal Address from ‘An’ to ‘An +1’. The transition shown indicates the time required for the counter to advance. The ‘An +1’Address is written to during this cycle. 6. For Pipelined Mode user should add 1 cycle latency for outputs as per timing waveform of read cycle for pipelined operations. 6.42 19 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Waveform of Interrupt Timing CLKL tSW R/WL tSA ADDRESSL(3) tHA tHW (2) 3FFFF tSC CEL (1) tHC tINS INTR tINR tSC CER(1) tHC CLKR R/WR tSW tSA ADDRESSR(3) tHW tHA 3FFFF 5666 drw 19 NOTES: 1. CE0 = VIL and CE 1 = VIH 2. All timing is the same for Left and Right ports. 3. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. Truth Table III — Interrupt Flag Left Port CLKL ↑ ↑ ↑ ↑ R/WL L X X H (2) (1) Right Port CEL L X X L (2) A17L-A0L (3,4,5) INTL X X L H CLKR ↑ ↑ ↑ ↑ R/WR X H L X (2) CER(2) X L L X A17R-A0R(3,4,5) X 3FFFF 3FFFE X INTR L H X X Function Set Right INTR Flag Reset Right INTR Flag Set Left INTL Flag Reset Left INTL Flag 5666 tbl 12 3FFFF X X 3FFFE NOTES: 1. INTL and INTR must be initialized at power-up by Resetting the flags. 2. CE0 = VIL and CE 1 = VIH. R/W and CE are synchronous with respect to the clock and need valid set-up and hold times. 3. A17X is a NC for IDT70T3599, therefore Interrupt Addresses are 1FFFF and 1FFFE. 4. A17X and A16X are NC's for IDT70T3589, therefore Interrupt Addresses are FFFF and FFFE. 5. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. 6.42 20 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Waveform of Collision Timing(1,2) Both Ports Writing with Left Port Clock Leading CLKL tOFS tSA ADDRESSL (4) tHA A0 A1 A2 A3 tCOLS COLL (3) tCOLR tOFS CLKR tSA ADDRESSR (4) tHA A0 A1 A2 A3 tCOLS COLR tCOLR 5666 drw 20 NOTES: 1. CE0 = VIL, CE1 = VIH. 2. For reading port, OE is a Don't care on the Collision Detection Logic. Please refer to Truth Table IV for specific cases. 3. Leading Port Output flag might output 3tCYC2 + tCOLS after Address match. 4. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. Collision Detection Timing(3,4) Cycle Time 5ns 6ns 7.5ns tOFS (ns) Region 1 (ns) 0 - 2.8 0 - 3.8 0 - 5.3 (1) Region 2 (ns) 2.81 - 4.6 3.81 - 5.6 5.31 - 7.1 (2) NOTES: 1. Region 1 Both ports show collision after 2nd cycle for Addresses 0, 2, 4 etc. 2. Region 2 Leading port shows collision after 3rd cycle for addresses 0, 3, 6, etc. while trailing port shows collision after 2nd cycle for addresses 0, 2, 4 etc. 3. All the production units are tested to midpoint of each region. 4. These ranges are based on characterization of a typical device. 5666 tbl 13 Truth Table IV — Collision Detection Flag Left Port CLKL ↑ ↑ ↑ ↑ R/WL(1) H H L L CEL(1) L L L L A17L-A0L(2) MATCH MATCH MATCH MATCH COLL H L H L CLKR ↑ ↑ ↑ ↑ R/WR(1) H L H L Right Port CE R(1) L L L L A17R-A0R(2) MATCH MATCH MATCH MATCH COLR H H L L Function Both ports reading. Not a valid collision. No flag output on either port. Left port reading, Right port writing. Valid collision, flag output on Left port. Right port reading, Left port writing. Valid collision, flag output on Right port. Both ports writing. Valid collision. Flag output on both ports. 5666 tbl 14 NOTES: 1. CE 0 = VIL and CE1 = VIH. R/W and CE are synchronous with respect to the clock and need valid set-up and hold times. 2. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. 6.42 21 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform - Entering Sleep Mode (1,2) R/W (3) Timing Waveform - Exiting Sleep Mode (1,2) An An+1 (5) R/W OE (5) DATAOUT Dn Dn+1 (4) NOTES: 1. CE1 = V IH. 2. All timing is same for Left and Right ports. 3. CE0 has to be deactivated (CE0 = VIH) three cycles prior to asserting ZZ (ZZx = VIH) and held for two cycles after asserting ZZ (ZZx = V IH). 4. CE0 has to be deactivated (CE0 = VIH) one cycle prior to de-asserting ZZ (ZZx = VIL) and held for three cycles after de-asserting ZZ (ZZx = VIL). 5. The device must be in Read Mode (R/W High) when exiting sleep mode. Outputs are active but data is not valid until the following cycle. 6.42 22 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Functional Description The IDT70T3519/99/89 provides a true synchronous Dual-Port Static RAM interface. Registered inputs provide minimal set-up and hold times on address, data, and all critical control inputs. All internal registers are clocked on the rising edge of the clock signal, however, the self-timed internal write pulse width is independent of the cycle time. An asynchronous output enable is provided to ease asynchronous bus interfacing. Counter enable inputs are also provided to stall the operation of the address counters for fast interleaved memory applications. A HIGH on CE0 or a LOW on CE1 for one clock cycle will power down the internal circuitry to reduce static power consumption. Multiple chip enables allow easier banking of multiple IDT70T3519/99/89s for depth expansion configurations. Two cycles are required with CE0 LOW and CE1 HIGH to re-activate the outputs. If the user chooses the interrupt function, a memory location (mail box or message center) is assigned to each port. The left port interrupt flag (INTL) is asserted when the right port writes to memory location 3FFFE (HEX), where a write is defined as CER = R/WR = VIL per the Truth Table. The left port clears the interrupt through access of address location 3FFFE when CEL = VIL and R/WL = VIH. Likewise, the right port interrupt flag ( INT R ) is asserted when the left port writes to memory location 3FFFF (HEX) and to clear the interrupt flag (INTR), the right port must read the memory location 3FFFF (1FFFF or 1FFFE for IDT70T3599 and FFFF or FFFE for IDT70T3589). The message (36 bits) at 3FFFE or 3FFFF (1FFFF or 1FFFE for IDT70T3599 and FFFF or FFFE for IDT70T3589) is user-defined since it is an addressable SRAM location. If the interrupt function is not used, address locations 3FFFE and 3FFFF (1FFFF or 1FFFE for IDT70T3599 and FFFF or FFFE for IDT70T3589) are not used as mail boxes, but as part of the random access memory. Refer to Truth Table III for the interrupt operation. Collision is defined as an overlap in access between the two ports resulting in the potential for either reading or writing incorrect data to a specific address. For the specific cases: (a) Both ports reading - no data is corrupted, lost, or incorrectly output, so no collision flag is output on either port. (b) One port writing, the other port reading - the end result of the write will still be valid. However, the reading port might capture data that is in a state of transition and hence the reading port’s collision flag is output. (c) Both ports writing - there is a risk that the two ports will interfere with each other, and the data stored in memory will not be a valid write from either port (it may essentially be a random combination of the two). Therefore, the collision flag is output on both ports. Please refer to Truth Table IV for all of the above cases. The alert flag (COLX) is asserted on the 2nd or 3rd rising clock edge of the affected port following the collision, and remains low for one cycle. Please refer to Collision Detection Timing table on Page 21. During that next cycle, the internal arbitration is engaged in resetting the alert flag (this avoids a specific requirement on the part of the user to reset the alert flag). If two collisions occur on subsequent clock cycles, the second collision may not generate the appropriate alert Interrupts flag. A third collision will generate the alert flag as appropriate. In the event that a user initiates a burst access on both ports with the same starting address on both ports and one or both ports writing during each access (i.e., imposes a long string of collisions on contiguous clock cycles), the alert flag will be asserted and cleared every other cycle. Please refer to the Collision Detection timing waveform on Page Collision detection on the IDT70T3519/99/89 represents a 21. significant advance in functionality over current sync multi-ports, which have no such capability. In addition to this functionality the IDT70T3519/99/89 sustains the key features of bandwidth and flexibility. The collision detection function is very useful in the case of bursting data, or a string of accesses made to sequential addresses, in that it indicates a problem within the burst, giving the user the option of either repeating the burst or continuing to watch the alert flag to see whether the number of collisions increases above an acceptable threshold value. Offering this function on chip also allows users to reduce their need for arbitration circuits, typically done in CPLD’s or FPGA’s. This reduces board space and design complexity, and gives the user more flexibility in developing a solution. Sleep Mode Collision Detection The IDT70T3519/99/89 is equipped with an optional sleep or low power mode on both ports. The sleep mode pin on both ports is asynchronous and active high. During normal operation, the ZZ pin is pulled low. When ZZ is pulled high, the port will enter sleep mode where it will meet lowest possible power conditions. The sleep mode timing diagram shows the modes of operation: Normal Operation, No Read/Write Allowed and Sleep Mode. For normal operation all inputs must meet setup and hold times prior to sleep and after recovering from sleep. Clocks must also meet cycle high and low times during these periods. Three cycles prior to asserting ZZ (ZZx = VIH) and three cycles after de-asserting ZZ (ZZx = VIL), the device must be disabled via the chip enable pins. If a write or read operation occurs during these periods, the memory array may be corrupted. Validity of data out from the RAM cannot be guaranteed immediately after ZZ is asserted (prior to being in sleep). When exiting sleep mode, the device must be in Read mode (R/Wx = VIH)when chip enable is asserted, and the chip enable must be valid for one full cycle before a read will result in the output of valid data. During sleep mode the RAM automatically deselects itself. The RAM disconnects its internal clock buffer. The external clock may continue to run without impacting the RAMs sleep current (IZZ). All outputs will remain in high-Z state while in sleep mode. All inputs are allowed to toggle. The RAM will not be selected and will not perform any reads or writes. 6.42 23 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Depth and Width Expansion The IDT70T3519/99/89 features dual chip enables (refer to Truth Table I) in order to facilitate rapid and simple depth expansion with no requirements for external logic. Figure 4 illustrates how to control the various chip enables in order to expand two devices in depth. The IDT70T3519/99/89 can also be used in applications requiring expanded width, as indicated in Figure 4. Through combining the control signals, the devices can be grouped as necessary to accommodate applications needing 72-bits or wider. A18/A17/A16 IDT70T3519/99/89 CE0 CE1 VDD IDT70T3519/99/89 CE0 CE1 VDD Control Inputs Control Inputs IDT70T3519/99/89 CE1 CE0 IDT70T3519/99/89 CE1 CE0 BE, R/W, OE, CLK, ADS, REPEAT, CNTEN Control Inputs Control Inputs Figure 4. Depth and Width Expansion with IDT70T3519/99/89 5666 drw 23 , NOTE: 1. A18 is for IDT70T3519, A17 is for IDT70T3599, A16 is for IDT70T3589. 6.42 24 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges JTAG Timing Specifications tJF TCK tJCL tJCYC tJR tJCH Device Inputs(1)/ TDI/TMS tJS Device Outputs(2)/ TDO TRST tJRST Figure 5. Standard JTAG Timing 5666 drw 24 tJH tJDC tJRSR tJCD , NOTES: 1. Device inputs = All device inputs except TDI, TMS, and TRST. 2. Device outputs = All device outputs except TDO. JTAG AC Electrical Characteristics (1,2,3,4) 70T3519/99/89 Symbol tJCYC tJCH tJCL tJR tJF tJRST tJRSR tJCD tJDC tJS tJH Parameter JTAG Clock Input Period JTAG Clock HIGH JTAG Clock Low JTAG Clock Rise Time JTAG Clock Fall Time JTAG Reset JTAG Reset Recovery JTAG Data Output JTAG Data Output Hold JTAG Setup JTAG Hold Min. 100 40 40 ____ ____ Max. ____ ____ ____ Units ns ns ns ns ns ns ns ns ns ns ns 5666 tbl 15 3(1) 3 (1) 50 50 ____ ____ ____ 25 ____ ____ ____ 0 15 15 NOTES: 1. Guaranteed by design. 2. 30pF loading on external output signals. 3. Refer to AC Electrical Test Conditions stated earlier in this document. 4. JTAG operations occur at one speed (10MHz). The base device may run at any speed specified in this datasheet. 6.42 25 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Identification Register Definitions Instruction Field Revision Number (31:28) IDT Device ID (27:12) IDT JEDEC ID (11:1) ID Register Indicator Bit (Bit 0) Value 0x0 0x330 (1) Description Reserved for version number Defines IDT part number Allows unique identification of device vendor as IDT Indicates the presence of an ID register 5666 tbl 16 0x33 1 NOTE: 1. Device ID for IDT70T3599 is 0x331. Device ID for IDT70T3589 is 0x332. Scan Register Sizes Register Name Instruction (IR) Bypass (BYR) Identification (IDR) Boundary Scan (BSR) Bit Size 4 1 32 Note (3) 5666 tbl 17 System Interface Parameters Instruction EXTEST BYPASS IDCODE Code 0000 1111 0010 0100 Description Forces contents of the boundary scan cells onto the device outputs (1). Places the boundary scan register (BSR) between TDI and TDO. Places the bypass register (BYR) between TDI and TDO. Loads the ID register (IDR) with the vendor ID code and places the register between TDI and TDO. Places the bypass register (BYR) between TDI and TDO. Forces all device output drivers to a High-Z state except COLx & INTx outputs. Uses BYR. Forces contents of the boundary scan cells onto the device outputs. Places the bypass register (BYR) between TDI and TDO. Places the boundary scan register (BSR) between TDI and TDO. SAMPLE allows data from device inputs (2) to be captured in the boundary scan cells and shifted serially through TDO. PRELOAD allows data to be input serially into the boundary scan cells via the TDI. Several combinations are reserved. Do not use codes other than those identified above. For internal use only. 5666 tbl 18 HIGHZ CLAMP SAMPLE/PRELOAD 0011 0001 RESERVED PRIVATE 0101, 0111, 1000, 1001, 1010, 1011, 1100 0110,1110,1101 NOTES: 1. Device outputs = All device outputs except TDO. 2. Device inputs = All device inputs except TDI, TMS, and TRST . 3. The Boundary Scan Descriptive Language (BSDL) file for this device is available on the IDT website (www.idt.com), or by contacting your local IDT sales representative. 6.42 26 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Ordering Information IDT XXXXX A Power 999 Speed A Package A Process/ Temperature Range Device Type Blank I BC DR BF 200 166 133 S Commercial (0°C to +70°C) Industrial (-40°C to +85°C) 256-pin BGA (BC-256) 208-pin PQFP (DR-208) 208-pin fpBGA (BF-208) Commercial Only(2) Commercial & Industrial(1) Speed in Megahertz Commercial & Industrial Standard Power 70T3519 9Mbit (256K x 36) 2.5V Synchronous Dual-Port RAM 70T3599 4Mbit (128K x 36) 2.5V Synchronous Dual-Port RAM 70T3589 2Mbit (64K x 36) 2.5V Synchronous Dual-Port RAM NOTES: 1. 166MHz I-Temp is not available in the BF-208 package. 2. 200Mhz is not available in the BF-208 and DR-208 packages. 5666 drw 25 IDT Clock Solution for IDT70T3519/99/89 Dual-Port Dual-Port I/O Specitications IDT Dual-Port Part Number Voltage I/O Input Capacitance Clock Specifications Input Duty Cycle Requirement 40% Maximum Frequency Jitter Tolerance IDT PLL Clock Device IDT Non-PLL Clock Device 5T9010 5T905, 5T9050 5T907, 5T9070 5666 tbl 19 70T3519/99/89 2.5 LVTTL 8pF 200 75ps 5T2010 6.42 27 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Datasheet Document History: 01/23/03: 01/30/03: 04/25/03: 11/11/03: Initial Datasheet Page 1 Corrected 208-pin package from TQFP to PQFP Page 11 Added Capacitance Derating drawing Page 12 Changed tINS and tINR specs in AC Electrical Characteristics table Page 10 Updated power numbers in DC Electrical Characteristics table Page 12 Added tOFS symbol and parameter to AC Electrical Characteristics table Page 21 Updated Collision Timing waveform Page 22 Added Collision DetectionTiming table and footnotes Page 26 Updated HIGHZ function in System Interface Parameters table Page 27 Added IDT Clock Solution table Page 22 & 23 Clarified Sleep Mode Text and Waveforms Page 1 & 27 Removed Preliminary status Page 6 Added another sentence to footnote 4 to recommend that boundary scan not be operated during sleep mode 03/30/04: 04/22/04: CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-5166 fax: 408-492-8674 www.idt.com for Tech Support: 831-754-4613 DualPortHelp@idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 28