IDT71V632S7PF8

64K x 32 3.3V Synchronous SRAM Pipelined Outputs Burst Counter, Single Cycle Deselect Features x x IDT71V632 x x x x x x 64K x 32 memory configuration Supports high system speed: Commercial: – A4 4.5ns clock access time (117 MHz) Commercial and Industrial: – 5 5ns clock access time (100 MHz) – 6 6ns clock access time (83 MHz) – 7 7ns clock access time (66 MHz) Single-cycle deselect functionality (Compatible with Micron Part # MT58LC64K32D7LG-XX) LBO input selects interleaved or linear burst mode Self-timed write cycle with global write control (GW), byte write enable (BWE), and byte writes (BWx) Power down controlled by ZZ input Operates with a single 3.3V power supply (+10/-5%) Packaged in a JEDEC Standard 100-pin rectangular plastic thin quad flatpack (TQFP). Description The IDT71V632 is a 3.3V high-speed SRAM organized as 64K x 32 with full support of the Pentium™ and PowerPC™ processor interfaces. The pipelined burst architecture provides cost-effective 3-1-1-1 secondary cache performance for processors up to 117MHz. The IDT71V632 SRAM contains write, data, address, and control registers. Internal logic allows the SRAM to generate a self-timed write based upon a decision which can be left until the extreme end of the write cycle. The burst mode feature offers the highest level of performance to the system designer, as the IDT71V632 can provide four cycles of data for a single address presented to the SRAM. An internal burst address counter accepts the first cycle address from the processor, initiating the access sequence. The first cycle of output data will be pipelined for one cycle before it is available on the next rising clock edge. If burst mode operation is selected (ADV=LOW), the subsequent three cycles of output data will be available to the user on the next three rising clock edges. The order of these three addresses will be defined by the internal burst counter and the LBO input pin. The IDT71V632 SRAM utilizes IDT's high-performance, high-volume 3.3V CMOS process, and is packaged in a JEDEC Standard 14mm x 20mm 100-pin thin plastic quad flatpack (TQFP) for optimum board density in both desktop and notebook applications. Pin Description Summary A0–A15 CE CS0, CS1 OE GW BWE BW1, BW2, BW3, BW4 CLK ADV ADSC ADSP LBO ZZ I/O0–I/O31 VDD, VDDQ VSS, VSSQ Address Inputs Chip Enable Chips Selects Output Enable Global Write Enable Byte Write Enable Individual Byte Write Selects Clock Burst Address Advance Address Status (Cache Controller) Address Status (Processor) Linear / Interleaved Burst Order Sleep Mode Data Input/Output 3.3V Array Ground, I/O Ground Input Input Input Input Input Input Input Input Input Input Input Input Input I/O Power Power Synchronous Synchronous Synchronous Asynchronous Synchronous Synchronous Synchronous N/A Synchronous Synchronous Synchronous DC Asynchronous Synchronous N/A N/A 3619 tbl 01 Pentium processor is a trademark of Intel Corp. PowerPC is a trademark of International Business Machines, Inc. AUGUST 2001 1 DSC-3619/04 ©2000 Integrated Device Technology, Inc. IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Pin Definitions(1) Symbol A0–A15 ADSC Pin Function Address Inputs Address Status (Cache Controller) I/O I I Active N/A LOW Description Synchronous Address inputs. The address re gister is triggered by a combination of the rising edge of CLK and ADSC Low or ADSP Low and C E Low. Synchronous Address Status from Cache Controller. ADSC is an active LOW input that is used to load the add ress registers with new addresses. ADSC is NOT GATED by C E. Synchrono us Address Status from Processor. ADSP is an active LOW input that is used to load the address registers with new addresses. ADSP is gated by CE. Synchronous Address Advance. ADV is an active LOW input that is used to advance the internal burst counter, controlling burst access after the initial address is loaded. When this input is HIGH the burst counter is not incremented; that is, there is no address advance. Synchronous byte write enable gates the byte write inputs BW1–BW4. If BWE is LOW at the rising edge of CLK then BWX inputs are passed to the next stage in the circuit. A byte write can still be blocked if ADSP is LOW at the rising edge of CLK. If ADSP is HIGH and BWX is LOW at the rising edge of CLK then data will be written to the SRAM. If BWE is HIGH then the byte write inputs are blocked and only GW can initiate a write cycle. Synchronous byte write enables. BW1 controls I/O(7:0), BW2 controls I/O(15:8), etc. Any active byte write causes all outputs to be disabled. ADSP LOW disables all byte writes. BW1–BW4 must meet specified setup and hold times with respect to CLK. Synchronous chip enable. C E is used with CS 0 and C S1 to enable the IDT71V632. C E also gates ADSP. This is the clock input. All timing references for the device are made with respect to this input. Synchronous active HIGH chip select. CS0 is used with C E and C S1 to enable the chip. Synchronous active LOW chip select. C S1 is used with C E and CS0 to enable the chip. Synchrono us global write enable. This input will write all four 8-bit data bytes when LOW on the rising edge of CLK. GW supercedes individual byte write enables. Synchronous data input/output (I/O) pins. Both the data input path and data output path are registered and triggered by the rising edge of CLK. Asynchronous burst order sele ction DC input. When LBO is HIGH the Interleaved (Intel) burst sequence is selected. When LBO is LOW the Linear (PowerPC) burst sequence is selected. LBO is a static DC input and must not change state while the device is operating. Asynchronous output enable. When OE is LOW the data output drivers are enabled on the I/O pins if the chip is also selected. When OE is HIGH the I/O pins are in a high-impedence state. 3.3V core power supply inputs. 3.3V I/O power supply inputs. Core ground pins. I/O ground pins. NC pins are not electrically connected to the chip. Asynchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the IDT71V632 to its lowest power consumption level. Data retention is guaranteed in Sleep Mode. 3619 tbl 02 ADSP Address Status (Processor) Burst Address Advance I LOW ADV I LOW BWE Byte Write Enable I LOW BW1–BW4 Individual Byte Write Enables I LOW CE CLK CS 0 CS1 Chip Enable Clock Chip Select 0 Chip Select 1 I I I I LOW N/A HIGH LOW GW Global Write Enable I LOW I/O0–I/O31 LBO Data Input/Output Linear Burst Order I/O I N/A LOW OE Output Enable I LOW VDD VDDQ VSS VSSQ NC ZZ Power Supply Power Supply Ground Ground No Connect Sleep Mode N/A N/A N/A N/A N/A I N/A N/A N/A N/A N/A HIGH NOTE: 1. All synchronous inputs must meet specified setup and hold times with respect to CLK. 6.42 2 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Functional Block Diagram LBO ADV CE Burst Sequence INTERNAL ADDRESS CLK ADSC ADSP CLK EN ADDRESS REGISTER Byte 1 Write Register Binary Counter CLR 2 Burst Logic 16 A0* A1* Q0 Q1 64K x 32 BIT MEMORY ARRAY . 32 2 16 A0–A15 GW BWE BW1 A0, A1 A2–A15 32 Byte 1 Write Driver Byte 2 Write Register 8 Byte 2 Write Driver BW2 Byte 3 Write Register 8 Byte 3 Write Driver BW3 Byte 4 Write Register 8 Byte 4 Write Driver BW4 8 OUTPUT REGISTER CE CS0 CS1 D Q Enable Register CLK EN DATA INPUT REGISTER ZZ Powerdown D Q Enable Delay Register OE OUTPUT BUFFER OE 32 I/O0–I/O31 3619 drw 01 6.42 3 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Absolute Maximum Ratings(1) Symbol VTERM VTERM TA TBIAS TSTG PT IOUT (2) Rating Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Operating Temperature Temperature Under Bias Storage Temperature Power Dissipation DC Output Current Value –0.5 to +4.6 –0.5 to VDD+0.5 0 to +70 –55 to +125 –55 to +125 1.0 50 Unit V V o o o Recommended Operating Temperature and Supply Voltage Grade Commercial Industrial Temperature 0°C to +70°C –40°C to +85°C VSS 0V 0V VDD VDDQ 3.3V+10/-5% 3.3V+10/-5% 3.3V+10/-5% 3.3V+10/-5% 3619 tbl 03 (3) C C C W mA 3619 tbl 05 Recommended DC Operating Conditions Sym bol V DD V DDQ V SS, V SSQ V IH V IH V IL Param eter Co re S up p ly Vo ltag e I/O S up p ly Vo ltag e G ro und Inp ut Hig h Vo ltag e — Inp uts Inp ut Hig h Vo ltag e — I/O Inp ut Lo w Vo ltag e M in. 3.135 3.135 0 2.0 2.0 –0.3 (3) M ax. 3.63 3.63 0 5.0 (1) (2) Unit V V V V V V 3619 tbl 04 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDD, VDDQ and Input terminals only. 3. I/O terminals. V DDQ + 0.3 0.8 Capacitance Symbol CIN CI/O (TA = +25°C, f = 1.0MHz, TQFP package) Parameter(1) Input Capacitance I/O Capacitance Conditions VIN = 3dV VOUT = 3dV Max. 6 7 Unit pF pF 3619 tbl 06 NOTES: 1. VIH (max) = 6.0V for pulse width less than tCYC/2, once per cycle. 2. VIH (max) = VDDQ + 1.0V for pulse width less than tCYC/2, once per cycle. 3. VIL (min) = –1.0V for pulse width less than tCYC/2, once per cycle. NOTE: 1. This parameter is guaranteed by device characterization, but not production tested. 6.42 4 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Pin Configuration A6 A7 CE CS0 BW4 BW3 BW2 BW1 CS1 VDD VSS CLK GW BWE OE ADSC ADSP ADV A8 A9 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 NC I/O16 I/O17 VDDQ VSSQ I/O18 I/O19 I/O20 I/O21 VSSQ VDDQ I/O22 I/O23 VDD/NC(1) VDD NC VSS I/O24 I/O25 VDDQ VSSQ I/O26 I/O27 I/O28 I/O29 VSSQ VDDQ I/O30 I/O31 NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 80 79 78 77 76 75 74 73 72 71 70 69 68 67 PK100-1 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 NC I/O15 I/O14 VDDQ VSSQ I/O13 I/O12 I/O11 I/O10 VSSQ VDDQ I/O9 I/O8 VSS NC VDD ZZ(2) I/O7 I/O6 VDDQ VSSQ I/O5 I/O4 I/O3 I/O2 VSSQ VDDQ I/O1 I/O0 NC LBO A5 A4 A3 A2 A1 A0 NC NC VSS VDD NC NC A10 A11 A12 A13 A14 A15 NC 3619 drw 02 Top View TQFP NOTES: 1. Pin 14 can either be directly connected to VDD or not connected. 2. Pin 64 can be left unconnected and the device will always remain in active mode. 6.42 5 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Synchronous Truth Table(1,2) Operation Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Deselected Cycle, Power Down Read Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Begin Burst Read Cycle, Begin Burst Write Cycle, Begin Burst Write Cycle, Begin Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Read Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Write Cycle, Continue Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Read Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst Write Cycle, Suspend Burst NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. ZZ = LOW for this table. 3. OE is an asynchronous input. Address Used None None None None None External External External External External External External Next Next Next Next Next Next Next Next Next Next Next Next Current Current Current Current Current Current Current Current Current Current Current Current CE H L L L L L L L L L L L X X X X H H H H X X H H X X X X H H H H X X H H CS0 X X L X L H H H H H H H X X X X X X X X X X X X X X X X X X X X X X X X CS1 X H X H X L L L L L L L X X X X X X X X X X X X X X X X X X X X X X X X ADSP X L L X X L L H H H H H H H H H X X X X H H X X H H H H X X X X H H X X ADSC L X X L L X X L L L L L H H H H H H H H H H H H H H H H H H H H H H H H ADV X X X X X X X X X X X X L L L L L L L L L L L L H H H H H H H H H H H H GW X X X X X X X H H H H L H H H H H H H H H L H L H H H H H H H H H L H L BWE X X X X X X X H L L L X H H X X H H X X L X L X H H X X H H X X L X L X BWX X X X X X X X X H H L X X X H H X X H H L X L X X X H H X X H H L X L X OE(3) X X X X X L H L L H X X L H L H L H L H X X X X L H L H L H L H X X X X CLK ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ I/O Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z DOUT Hi-Z DOUT DOUT Hi-Z DIN DIN DOUT Hi-Z DOUT Hi-Z DOUT Hi-Z DOUT Hi-Z DIN DIN DIN DIN DOUT Hi-Z DOUT Hi-Z DOUT Hi-Z DOUT Hi-Z DIN DIN DIN DIN 3619 tbl 07 6.42 6 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Synchronous Write Function Truth Table(1) Operation Read Read Write all Bytes Write all Bytes Write Byte 1 Write Byte 2 Write Byte 3 (2) (2) (2) GW H H L H H H H H BWE H L X L L L L L BW1 X H X L L H H H BW2 X H X L H L H H BW3 X H X L H H L H BW4 X H X L H H H L 3619 tbl 08 Write Byte 4(2) NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. Multiple bytes may be selected during the same cycle. Asynchronous Truth Table(1) Operation(2) Read Read Write Deselected Sleep OE L H X X X ZZ L L L L H I/O Status Data Out (I/O0 - I/O31) High-Z High-Z — Data In (I/O 0 - I/O31) High-Z High-Z Power Active Active Active Standby Sleep 3619 tbl 09 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. Synchronous function pins must be biased appropriately to satisfy operation requirements. Interleaved Burst Sequence Table (LBO=VDD) Sequence 1 A1 First Address Second Address Third Address Fourth Address (1) Sequence 2 A1 0 0 1 1 A0 1 0 1 0 Sequence 3 A1 1 1 0 0 A0 0 1 0 1 Sequence 4 A1 1 1 0 0 A0 1 0 1 0 3619 tbl 10 A0 0 1 0 1 0 0 1 1 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state. Linear Burst Sequence Table (LBO=VSS) Sequence 1 A1 First Address Second Address Third Address Fourth Address (1) Sequence 2 A1 0 1 1 0 A0 1 0 1 0 Sequence 3 A1 1 1 0 0 A0 0 1 0 1 Sequence 4 A1 1 0 0 1 A0 1 0 1 0 3619 tbl 11 A0 0 1 0 1 0 0 1 1 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state. 6.42 7 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V +10/-5%) Symbol |ILI| |ILZZ| |ILO| VOL (3.3V) VOH (3.3V) Parameter Input Leakage Current ZZ and LBO Input Leakage Current (1) Output Leakage Current Output Low Voltage Output High Voltage Test Conditions VDD = M ax., VIN = 0V to VDD VDD = M ax., VIN = 0V to VDD CE > VIH or OE > VIH, VOUT = 0V to VDD, VDD = M ax. IOL = 5mA, VDD = M in. IOH = –5mA, VDD = M in. Min. — — — — 2.4 Max. 5 30 5 0.4 — Unit µA µA µA V V 3619 tbl 12 NOTE: 1. The LBO pin will be internally pulled to VDD if it is not actively driven in the application and the ZZ pin will be internally pulled to VSS if not actively driven. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1) (VHD = VDDQ – 0.2V, VLD = 0.2V) SA4(3,4) Symbol IDD Parameter Operating Power Supply Current Standby Power Supply Current Full Standby Power Supply Current Full Sleep Mode Power Supply Current Test Conditions Device Selected, Outputs Open, VDD = M ax., VIN > VIH or < VIL, f = fMAX(2) Device Deselected, Outputs Open, VDD = M ax., VIN > VIH or < VIL, f = fMAX(2) Device Deselected, Outputs Open, VDD = M ax., VIN > VHD or < VLD, f = 0(2) ZZ > VHD, VDD = M ax. Com'l. 220 Ind. — Com'l. 200 S5 Ind. 200 Com'l. 180 S6 Ind. 180 Com'l. 160 S7 Ind. 160 Unit mA ISB 70 — 65 65 60 60 55 55 mA ISB1 15 — 15 15 15 15 15 15 mA IZZ 10 — 10 10 10 10 10 10 mA 3619 tbl 13 NOTES: 1. All values are maximum guaranteed values. 2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC while ADSC = LOW; f=0 means no input lines are changing. 3. SA4 speed grade corresponds to a tCD of 4.5 ns. 4. 0°C to +70°C temperature range only. AC Test Loads VDDQ/2 50Ω I/O Z0 = 50Ω Figure 1. AC Test Load 6 5 4 3 ∆tCD (Typical, ns) 2 1 20 30 50 80 100 Capacitance (pF) 200 3619 drw 05 +3.3V 317Ω I/O 351Ω 5pF* 3619 drw 03 * Including scope and jig capacitance. 3619 drw 04 Figure 2. High-Impedence Test Load (for tOHZ, tCHZ, tOLZ, and tDC1) AC Test Conditions Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Timing Reference Levels AC Test Load 0 to 3.0V 2ns 1.5V 1.5V See Figures 1 and 2 3619 tbl 14 Figure 3. Lumped Capacitive Load, Typical Derating 6.42 8 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges AC Electrical Characteristics (VDD, VDDQ = 3.3V +10/-5%, Commercial and Industrial Temperature Ranges) 71V632SA4(5,6) Symbol CLOCK PARAMETERS tCYC tCH (1) 71V632S5 Min. Max. 71V632S6 Min. Max. 71V632S7 Min. Max. Unit Parameter Min. Max. Clock Cycle Time Clock High Pulse Width Clock Low Pulse Width 8.5 3.5 3.5 ____ ____ ____ 10 4 4 ____ ____ ____ 12 4.5 4.5 ____ ____ ____ 15 5 5 ____ ____ ____ ns ns ns tCL(1) OUTPUT PARAMETERS tCD tCDC tCLZ (2) Clock High to Valid Data Clock High to Data Change Clock High to Output Active Clock High to Data High-Z Output Enable Access Time (2) (2) ____ 4.5 ____ ____ ____ 5 ____ ____ ____ 6 ____ ____ ____ 7 ____ ____ ns ns ns ns ns ns ns 1.5 0 1.5 ____ 1.5 0 1.5 ____ 2 0 2 ____ 2 0 2 ____ tCHZ(2) tOE tOLZ 4 4 ____ 5 5 ____ 5 5 ____ 6 6 ____ Output Enable Low to Data Active Output Enable High to Data High-Z 0 ____ 0 ____ 0 ____ 0 ____ tOHZ 4 4 5 6 SETUP TIMES tSA tSS tSD tSW tSAV tSC HOLD TIMES tHA tHS tHD tHW tHAV tHC Address Hold Time Address Status Hold Time Data In Hold Time Write Hold Time Address Advance Hold Time Chip Enable/Select Hold Time 0.5 0.5 0.5 0.5 0.5 0.5 ____ ____ ____ ____ ____ ____ Address Setup Time Address Status Setup Time Data in Setup Time Write Setup Time Address Advance Setup Time Chip Enable/Select Setup Time 2.2 2.2 2.2 2.2 2.2 2.2 ____ ____ ____ ____ ____ ____ 2.5 2.5 2.5 2.5 2.5 2.5 ____ ____ ____ ____ ____ ____ 2.5 2.5 2.5 2.5 2.5 2.5 ____ ____ ____ ____ ____ ____ 2.5 2.5 2.5 2.5 2.5 2.5 ____ ____ ____ ____ ____ ____ ns ns ns ns ns ns 0.5 0.5 0.5 0.5 0.5 0.5 ____ ____ ____ ____ ____ ____ 0.5 0.5 0.5 0.5 0.5 0.5 ____ ____ ____ ____ ____ ____ 0.5 0.5 0.5 0.5 0.5 0.5 ____ ____ ____ ____ ____ ____ ns ns ns ns ns ns SLEEP MODE AND CONFIGURATION PARAMETERS tZZPW tZZR(3) tCFG (4) ZZ Pulse Width ZZ Recovery Time Configuration Set-up Time 100 100 34 ____ ____ ____ 100 100 40 — — — 100 100 50 ____ ____ ____ 100 100 50 ____ ____ ____ ns ns ns 3619 tbl 15 NOTES: 1. Measured as HIGH above 2.0V and LOW below 0.8V. 2. Transition is measured ±200mV from steady-state. 3. Device must be deselected when powered-up from sleep mode. 4. tCFG is the minimum time required to configure the device based on the LBO input. LBO is a static input and must not change during normal operation. 5. The 71V632SA4 speed grade corresponds to a tCD of 4.5ns. 6. 0°C to +70°C temperature range only. 6.42 9 tCYC CLK tCH tCL tSS tHS ADSP (1) ADSC tHA Ax tSW tHW Ay tSA ADDRESS GW, BWE, BWx tHC tSAV tHAV IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect tSC CE, CS1 (Note 3) ADV tOE tCD tOHZ tCDC O1(Ay) O2(Ay) O3(Ay) ADV inserts a wait-state Timing Waveform of Pipelined Read Cycle(1,2) 6.42 10 tOLZ tCLZ O1(Ax) OE (Burst wraps around to its initial state) tCHZ O4(Ay) O1(Ay) O2(Ay) DATAOUT Output Disabled Pipelined Read Burst Pipelined Read 3619 drw 06 Commercial and Industrial Temperature Ranges NOTES: 1. O1 (Ax) represents the first output from the external address Ax. O1 (Ay) represents the first output from the external address Ay; O2 (Ay) represents the next output data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. ZZ input is LOW and LBO is Don’t Care for this cycle. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. tCYC CLK tCH (2) tSS tHS tCL ADSP tSA tHA Ax Ay tSW tHW Az ADDRESS IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect GW ADV Timing Waveform of Combined Pipelined Read and Write Cycles(1,2,3) 6.42 11 OE tSD tHD tOE tCD tCLZ O1(Ax) tOHZ I1(Ay) tOLZ DATAIN tCDC O1(Az) O2(Az) O3(Az) DATAOUT Single Read Pipelined Write Pipelined Burst Read 3619 drw 07 Commercial and Industrial Temperature Ranges NOTES: 1. Device is selected through entire cycle; CE and CS1 are LOW, CS0 is HIGH. 2. ZZ input is LOW and LBO is Don’t Care for this cycle. 3. O1(Ax) represents the first output from the external address Ax. I1 (Ay) represents the first input from the external address Ay. O1(Az) represents the first output from the external addresss Az; O2(Az) represents the next output data in the burst sequence of the base address Az, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. tCYC CLK tCH tCL tSS tHS ADSP ADSC tSA tHA Ax BWE is ignored when ADSP initiates burst ADDRESS Ay Az tHW tSW GW IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect tSC tHC CE, CS1 tSAV tHAV (Note 3) ADV (ADV suspends burst) Timing Waveform of Write Cycle No. 1 — GW Controlled(1,2,3) 6.42 12 I1(Ax) I2(Ay) tOHZ O4(Aw) I1(Ay) I2(Ay) Burst Write Single Write OE tSD I3(Ay) I4(Ay) I1(Az) tHD DATAIN I2(Az) I3(Az) DATAOUT O3(Aw) Burst Read Burst Write 3619 drw 08 Commercial and Industrial Temperature Ranges NOTES: 1. ZZ input is LOW, BWE is HIGH, and LBO is Don’t Care for this cycle. 2. O4(Aw) represents the final output data in the burst sequence of the base address Aw. I1(Ax) represents the first input from the external address Ax. I1(Ay) represents the first input from the external address Ay; I2(Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. In the case of input I2(Ay) this data is valid for two cycles because ADV is high and has suspended the burst. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. . tCYC CLK tCH tCL tSS tHS ADSP ADSC tSA tHA Ax BWE is ignored when ADSP initiates burst ADDRESS Az tHW tSW Ay BWE BWx is ignored when ADSP initiates burst tHW tSW IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect BWx tSC tHC CE, CS1 tSAV (Note 3) Timing Waveform of Write Cycle No. 2 — Byte Controlled(1,2,3) 6.42 13 (ADV suspends burst) ADV OE tSD I1(Ax) I2(Ay) tOHZ I1(Ay) I2(Ay) I3(Ay) I4(Ay) I1(Az) tHD DATAIN I2(Az) I3(Az) DATAOUT Single Write O3(Aw) O4(Aw) Burst Write Extended Burst Write 3619 drw 09 Burst Read Commercial and Industrial Temperature Ranges NOTES: 1. ZZ input is LOW, GW is HIGH, and LBO is Don’t Care for this cycle. 2. O4(Aw) represents the final output data in the burst sequence of the base address Aw. I1(Ax) represents the first input from the external address Ax. I1(Ay) represents the first input from the external address Ay; I2(Ay) represents the next input data in the burst sequence of the base address Ay, etc. where A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. In the case of input I2(Ay) this data is valid for two cycles because ADV is high and has suspended the burst. 3. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. tCYC CLK tCH tCL tSS tHS ADSP ADSC tHA Ax Az tSA ADDRESS IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect GW tHC tSC CE, CS1 (Note 4) Timing Waveform of Sleep (ZZ) and Power-Down Modes(1,2,3) 6.42 14 tOE tOLZ O1(Ax) ADV OE DATAOUT t ZZR t ZZPW Single Read Snooze Mode 3619 drw 10 ZZ Commercial and Industrial Temperature Ranges NOTES: 1. Device must power up in deselected Mode. 2. LBO input is Don’t Care for this cycle. 3. It is not necessary to retain the state of the input registers throughout the Power-down cycle. 4. CS0 timing transitions are identical but inverted to the CE and CS1 signals. For example, when CE and CS1 are LOW on this waveform, CS0 is HIGH. IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Non-Burst Read Cycle Timing Waveform CLK ADSP ADSC ADDRESS Av Aw Ax Ay Az GW, BWE, BWx CE, CS1 CS0 OE DATAOUT (Av) (Aw) (Ax) (Ay) , 3619 drw 11 NOTES: 1. ZZ input is LOW, ADV is HIGH and LBO is Don’t Care for this cycle. 2. (AX) represents the data for address AX, etc. 3. For read cycles, ADSP and ADSC function identically and are therefore interchangeable. 6.42 15 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Non-Burst Write Cycle Timing Waveform CLK ADSP ADSC ADDRESS Av Aw Ax Ay Az GW CE, CS1 CS0 DATAIN (Av) (Aw) (Ax) (Ay) (Az) , 3619 drw 12 NOTES: 1. ZZ input is LOW, ADV and OE are HIGH, and LBO is Don’t Care for this cycle. 2. (AX) represents the data for address AX, etc. 3. Although only GW writes are shown, the functionality of BWE and BWx together is the same as GW. 4. For write cycles, ADSP and ADSC have different limitations. 6.42 16 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges 100-pin Thin Quad Plastic Flatpack (TQFP) Package Diagram Outline 6.42 17 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Ordering Information IDT 71V632 Device Type S Power X Speed PF Package X Process/ Temperature Range Blank I Commercial (0°C to +70°C) Industrial (–40°C to +85°C) PF Plastic Thin Quad Flatpack, 100 pin (PK100-1) A4* 5 6 7 Synchronous Access Time in nanoseconds * Commercial only. PART NUMBER 71V632SA4PF 71V632S5PF 71V632S6PF 71V632S7PF SPEED IN MEGAHERTZ 117 MHz 100 MHz 83 MHz 66 MHz tCD PARAMETER 4.5 ns 5 ns 6 ns 7 ns CLOCK CYCLE TIME 8.5 ns 10 ns 12 ns 15 ns 3619 drw 13 6.42 18 IDT71V632, 64K x 32, 3.3V Synchronous SRAM with Pipelined Outputs and Single Cycle Deselect Commercial and Industrial Temperature Ranges Datasheet Document History 9/9/99 Pg. 1, 8, 9, 17 Pg. 15, 16 Pg. 18 Pg. 1, 4, 8, 9, 17 Pg. 17 Updated to new format Revised speed offerings to 66–117MHz Added non-burst read and write cycle timing diagrams Added Datasheet Document History Added industrial temperature range offerings Added 100pinTQFP package Diagram Outline Not recommended for new designs Removed “Not recommended for new designs” from the background on the datasheet 09/30/99 04/04/00 08/09/00 08/17/01 CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 6.42 19 for Tech Support: sramhelp@idt.com 800-544-7726, x4033 The IDT logo is a registered trademark of Integrated Device Technology, Inc.