IDT71V65603

256K x 36, 512K x 18 3.3V Synchronous ZBT™ SRAMs ZBT™ Feature 3.3V I/O, Burst Counter Pipelined Outputs x x x x x x x x x x x x x IDT71V65603 IDT71V65803 Features 256K x 36, 512K x 18 memory configurations Supports high performance system speed - 150MHz (3.8ns Clock-to-Data Access) ZBTTM Feature - No dead cycles between write and read cycles Internally synchronized output buffer enable eliminates the need to control OE Single R/W (READ/WRITE) control pin Positive clock-edge triggered address, data, and control signal registers for fully pipelined applications 4-word burst capability (interleaved or linear) Individual byte write (BW1 - BW4) control (May tie active) Three chip enables for simple depth expansion 3.3V power supply (±5%) 3.3V I/O Supply (VDDQ) Power down controlled by ZZ input Packaged in a JEDEC standard 100-pin plastic thin quad flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch ball grid array(fBGA). Description The IDT71V65603/5803 are 3.3V high-speed 9,437,184-bit (9 Megabit) synchronous SRAMS. They are designed to eliminate dead bus cycles when turning the bus around between reads and writes, or writes and reads. Thus, they have been given the name ZBTTM, or Zero Bus Turnaround. Address and control signals are applied to the SRAM during one clock cycle, and two cycles later the associated data cycle occurs, be it read or write. The IDT71V65603/5803 contain data I/O, address and control signal registers. Output enable is the only asynchronous signal and can be used to disable the outputs at any given time. A Clock Enable (CEN) pin allows operation of the IDT71V65603/5803 to be suspended as long as necessary. All synchronous inputs are ignored when (CEN) is high and the internal device registers will hold their previous values. There are three chip enable pins (CE1, CE2, CE2) that allow the user to deselect the device when desired. If any one of these three are not asserted when ADV/LD is low, no new memory operation can be initiated. However, any pending data transfers (reads or writes) will be completed. The data bus will tri-state two cycles after chip is deselected or a write is initiated. The IDT71V65603/5803 have an on-chip burst counter. In the burst mode, the IDT71V65603/5803 can provide four cycles of data for a single address presented to the SRAM. The order of the burst sequence is defined by the LBO input pin. The LBO pin selects between linear and interleaved burst sequence. The ADV/LD signal is used to load a new external address (ADV/LD = LOW) or increment the internal burst counter (ADV/LD = HIGH). The IDT71V65603/5803 SRAM utilize IDT's latest high-performance CMOS process, and are packaged in a JEDEC Standard 14mm x 20mm 100pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array (BGA) and 165 fine pitch ball grid array (fBGA) . Pin Description Summary A0-A18 CE1, CE2, C E2 OE R/W CEN BW1, BW2, BW3, BW4 CLK ADV/LD LBO ZZ I/O0-I/O31, I/OP1-I/OP4 VDD, VDDQ VSS Address Inputs Chip Enables Output Enable Read/Write Signal Clock Enable Individual Byte Write Selects Clock Advance burst address / Load new address Linear / Interleaved Burst Order Sleep Mode Data Input / Output Core Power, I/O Power Ground Input Input Input Input Input Input Input Input Input Input I/O Supply Supply Synchronous Synchronous Asynchronous Synchronous Synchronous Synchronous N/A Synchronous Static Asynchronous Synchronous Static Static 5304 tbl 01 ZBT and Zero Bus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola, Inc. DECEMBER 2002 DSC-5304/05 1 ©2002 Integrated Device Technology, Inc. IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Pin Definitions(1) Symbol A0-A18 ADV/LD Pin Function Address Inputs Advance / Load I/O I I Active N/A N/A Description Synchronous Address inputs. The address register is triggered by a combination of the rising edge of CLK, ADV/LD low, CEN low, and true chip enables. ADV/LD is a synchronous input that is used to load the internal registers with new address and control when it is sampled low at the rising edge of clock with the chip selected. When ADV/LD is low with the chip deselected, any burst in progress is terminated. When ADV/ LD is sampled high then the internal burst counter is advanced for any burst that was in progress. The external addresses are ignored when ADV/ LD is sampled high. R/W signal is a synchronous input that identifies whether the current load cycle initiated is a Read or Write access to the memory array. The data bus activity for the current cycle takes place two clock cycles later. Synchronous Clock Enable Input. When CEN is sampled high, all other synchronous inputs, including clock are ignored and outputs re main unchanged. The effect of CEN sampled high on the device outputs is as if the low to high clock transition did not occur. For normal operation, CEN must be sampled low at rising edge of clock. Synchronous byte write enables. Each 9-bit byte has its own active low byte write enable. On load write cycles (When R/ W and ADV/LD are sampled low) the appropriate byte write signal (BW1-BW4) must be valid. The byte write signal must also be valid on each cycle of a burst write. Byte Write signals are ignored when R/ W is sampled high. The appropriate byte(s) of data are written into the device two cycles later. BW1-BW4 c an all be tied low if always doing write to the entire 36-bit word. Synchronous active low chip enable. CE1 and CE2 are used with CE2 to enable the IDT71V65603/5803. (CE1 o r CE2 s ampled high or CE2 sampled low) and ADV/LD low at the rising edge of clock, initiates a deselect cycle. The ZBTTM has a two cycle deselect, i.e., the data bus will tri-state two clock cycles after deselect is initiated. Synchronous active high chip enable. CE2 is used with CE1 and CE2 to enable the chip. CE2 has inverted polarity but otherwise identical to CE1 and CE2. This is the clock input to the IDT71V65603/5803. Except for OE, all timing references for the device are made with respect to the rising edge of CLK. Synchronous data input/output (I/O) pins. Both the data input path and data output path are registered and triggered by the rising edge of CLK. Burst order selection input. When LBO is high the Interleaved burst sequence is selected. When LBO is low the Linear burst sequence is selected. LBO is a static input and it must not change during device operation. Asynchronous output enable. OE must be low to read data from the 71V65603/5803. When OE is high the I/O pins are in a high-impedance state. OE d oes not need to be actively controlled for read and write cycles. In normal operation, OE can be tied low. Asynchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the 71V65603/5803 to its lowest power consumption level. Data retention is guaranteed in Sleep Mode. 3.3V core power supply. 3.3V I/O Supply. Ground. 5304tbl 02 R/W Read / Write I N/A CEN Clock Enable I LOW BW1-BW4 Individual Byte Write Enables I LOW CE1, CE2 Chip Enables I LOW CE2 CLK I/O0-I/O31 I/OP1-I/OP4 LBO Chip Enable Clock Data Input/Output Linear Burst Order I I I/O I HIGH N/A N/A LOW OE Output Enable I LOW ZZ Sleep Mode I N/A VDD VDDQ VSS NOTE: Power Supply Power Supply Ground N/A N/A N/A N/A N/A N/A 1. All synchronous inputs must meet specified setup and hold times with respect to CLK. 6.42 2 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Functional Block Diagram LBO Address A [0:17] CE1, CE2, CE2 R/W CEN ADV/LD BWx D Clk D Q Control D Q 256Kx36 BIT MEMORY ARRAY Address Input Register DI DO Q Control Logic Mux Sel D Clk Clock Output Register Q OE Gate 5304 drw 01a , Data I/O [0:31], I/O P[1:4] 6.42 3 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Functional Block Diagram LBO Address A [0:18] CE1, CE2, CE2 R/W CEN ADV/LD BWx D Clk D Q Control D Q 512x18 BIT MEMORY ARRAY Address Input Register DI DO Q Control Logic Mux Sel D Clk Clock Output Register Q OE Gate 5304 drw 01 , Data I/O [0:15], I/O P[1:2] Recommended DC Operating Conditions Symbol VDD VDDQ VSS VIH VIH VIL Parameter Core Supply Voltage I/O Supply Voltage Supply Voltage Input High Voltage - Inputs Input High Voltage - I/O Input Low Voltage Min. 3.135 3.135 0 2.0 2.0 -0.3(1) Typ. 3.3 3.3 0 ____ ____ ____ Max. 3.465 3.465 0 VDD+0.3 VDDQ+0.3 0.8 Unit V V V V V V 5304 tbl 04 NOTES: 1. VIL (min.) = –1.0V for pulse width less than tCYC/2, once per cycle. 6.42 4 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Recommended Operating Temperature and Supply Voltage Grade Commercial Industrial NOTES: Temperature(1) 0° C to +70° C -40°C to +85°C VSS 0V 0V VDD 3.3V±5% 3.3V±5% VDDQ 3.3V±5% 3.3V±5% 5304 tbl 05 1. TA is the "instant on" case temperature. 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 I/OP3 I/O16 I/O17 VDDQ VSS I/O18 I/O19 I/O20 I/O21 VSS VDDQ I/O22 I/O23 VDD(1) VDD VDD(1) VSS I/O24 I/O25 VDDQ VSS I/O26 I/O27 I/O28 I/O29 VSS VDDQ I/O30 I/O31 I/OP4 CE2 BW4 BW3 BW2 BW1 CE2 VDD VSS CLK R/W CEN OE ADV/LD NC(2) A17 A8 A9 Pin Configuration - 256K x 36 A6 A7 CE1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 I/OP2 I/O15 I/O14 VDDQ VSS I/O13 I/O12 I/O11 I/O10 VSS VDDQ I/O9 I/O8 VSS VDD(1) VDD ZZ I/O7 I/O6 VDDQ VSS I/O5 I/O4 I/O3 I/O2 VSS VDDQ I/O1 I/O0 I/OP1 5304 drw 02 NOTES: 1. Pins 14, 16 and 66 do not have to be connected directly to VDD as long as the input voltage is ≥ VIH. 2. Pin 84 is reserved for a future 16M. 3. DNU=Do not use. Pins 38, 39, 42 and 43 are reserved for respective JTAG pins: TMS, TDI, TDO and TCK. The current die revision allows these pins to be left unconnected, tied LOW (VSS), or tied HIGH (VDD). LBO A5 A4 A3 A2 A1 A0 DNU(3) DNU(3) VSS VDD DNU(3) DNU(3) A10 A11 A12 A13 A14 A15 A16 , Top View 100 TQFP 6.42 5 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Pin Configuration - 512K x 18 CE2 NC NC BW2 BW1 CE2 VDD VSS CLK R/W CEN OE ADV/LD NC(2) A18 A8 A9 A6 A7 CE1 Absolute Maximum Ratings(1) Symbol VTERM(2) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 Rating Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Commercial Operating Temperature Industrial Operating Temperature Commercial & Industrial -0.5 to +4.6 -0.5 to VDD -0.5 to VDD +0.5 -0.5 to VDDQ +0.5 -0 to +70 Unit V V V V o 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 NC NC NC VDDQ VSS NC NC I/O8 I/O9 VSS VDDQ I/O10 I/O11 VDD(1) VDD VDD(1) VSS I/O12 I/O13 VDDQ VSS I/O14 I/O15 I/OP2 NC VSS VDDQ NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A10 NC NC VDDQ VSS NC I/OP1 I/O7 I/O6 VSS VDDQ I/O5 I/O4 VSS VDD(1) VDD ZZ I/O3 I/O2 VDDQ VSS I/O1 I/O0 NC NC VSS VDDQ NC NC NC 5304 drw 02a VTERM(3,6) VTERM(4,6) VTERM(5,6) C TA (7) -40 to +85 -55 to +125 -55 to +125 2.0 50 o C C C TBIAS TSTG PT Temperature Under Bias Storage Temperature Power Dissipation DC Output Current o o W mA , IOUT LBO A5 A4 A3 A2 A1 A0 DNU(3) DNU(3) VSS VDD DNU(3) DNU(3) A11 A12 A13 A14 A15 A16 A17 NOTES: 1. Pins 14, 16 and 66 do not have to be connected directly to VDD as long as the input voltage is ≥ VIH. 2. Pin 84 is reserved for a future 16M. 3. DNU=Do not use. Pins 38, 39, 42 and 43 are reserved for respective JTAG pins: TMS, TDI, TDO and TCK. The current die revision allows these pins to be left unconnected, tied LOW (VSS), or tied HIGH (VDD). Top View 100 TQFP 5304 tbl 06 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDD terminals only. 3. VDDQ terminals only. 4. Input terminals only. 5. I/O terminals only. 6. This is a steady-state DC parameter that applies after the power supply has reached its nominal operating value. Power sequencing is not necessary; however, the voltage on any input or I/O pin cannot exceed VDDQ during power supply ramp up. 7. TA is the "instant on" case temperature. 100 TQFP Capacitance(1) (TA = +25° C, f = 1.0MHz) Symbol CIN CI/O Parameter(1) Input Capacitance I/O Capacitance Conditions VIN = 3dV VOUT = 3dV (1) 165 fBGA Capacitance(1) (TA = +25° C, f = 1.0MHz) Max. 5 7 Unit pF pF 5304 tbl 07 Symbol CIN CI/O Parameter(1) Input Capacitance I/O Capacitance Conditions VIN = 3dV VOUT = 3dV Max. TBD TBD Unit pF pF 5304 tbl 07b 119 BGA Capacitance (TA = +25° C, f = 1.0MHz) Symbol CIN CI/O Parameter(1) Input Capacitance I/O Capacitance Conditions VIN = 3dV VOUT = 3dV Max. 7 7 Unit pF pF 5304 tbl 07a NOTE: 1. This parameter is guaranteed by device characterization, but not production tested. 6.42 6 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Pin Configuration - 256K X 36, 119 BGA 1 A B C D E F G H J K L M N P R T U VDDQ NC NC I/O16 I/O17 VDDQ I/O20 I/O22 VDDQ I/O24 I/O25 VDDQ I/O29 I/O31 NC NC VDDQ 2 A6 CE 2 A7 I/OP3 I/O18 I/O19 I/O21 I/O23 VDD I/O26 I/O27 I/O28 I/O30 I/OP4 A5 NC DNU (3) 3 A4 A3 A2 VSS VSS VSS BW3 VSS VDD(1) VSS BW4 VSS VSS VSS LBO A10 DNU (3) 4 NC(2) ADV/LD VDD NC CE1 OE A17 R/W VDD CLK NC CEN A1 A0 VDD A11 DNU (3) 5 A8 A9 A12 VSS VSS VSS BW 2 VSS VDD(1) VSS BW1 VSS VSS VSS VDD(1) A14 DNU (3) 6 A16 CE2 A15 I/OP2 I/O13 I/O12 I/O11 I/O9 VDD I/O6 I/O4 I/O3 I/O2 I/OP1 A13 NC DNU (3) 7 VDDQ NC NC I/O15 I/O14 VDDQ I/O10 I/O8 VDDQ I/O7 I/O5 VDDQ I/O1 I/O0 NC ZZ VDDQ 5304 drw 13A , Top View Pin Configuration - 512K X 18, 119 BGA 1 A B C D E F G H J K L M N P R T U VDDQ NC NC I/O8 NC VDDQ NC I/O11 VDDQ NC I/O13 VDDQ I/O15 NC NC NC VDDQ 2 A6 CE2 A7 NC I/O9 NC I/O10 NC VDD I/O12 NC I/O14 NC I/OP2 A5 A10 DNU(3) 3 A4 A3 A2 VSS VSS VSS BW2 VSS VDD(1) VSS VSS VSS VSS VSS LBO A15 DNU(3) 4 NC(2) ADV/LD VDD NC CE1 OE A18 R/W VDD CLK NC CEN A1 A0 VDD NC DNU (3) 5 A8 A9 A13 VSS VSS VSS VSS VSS VDD(1) VSS BW1 VSS VSS VSS VDD(1) A14 DNU(3) 6 A16 CE2 A17 I/O7 NC I/O5 NC I/O3 VDD NC I/O1 NC I/O0 NC A12 A11 DNU(3) 7 VDDQ NC NC NC I/O6 VDDQ I/O4 NC VDDQ I/O2 NC VDDQ NC I/OP1 NC ZZ VDDQ 5304 drw 13B NOTES: 1. J3, J5, and R5 do not have to be directly connected to VDD as long as the input voltage is ≥ VIH. 2. A4 is reserved for future 16M. 3. DNU = Do not use. Pin U2, U3, U4, U5 and U6 are reserved for respective JTAG pins: TMS, TDI, TCK, TDO and TRST. these pins to be left unconnected, tied LOW (VSS), or tied HIGH (VDD). Top View The current die revision allows 6.42 7 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Pin Configuration - 256K X 36, 165 fBGA 1 A B C D E F G H J K L M N P R NC(2) NC I/OP3 I/O17 I/O19 I/O21 I/O23 VDD(1) I/O25 I/O27 I/O29 I/O31 I/OP4 NC LBO 2 A7 A6 NC I/O16 I/O18 I/O20 I/O22 VDD(1) I/O24 I/O26 I/O28 I/O30 NC NC(2) NC(2) 3 CE1 CE 2 VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A5 A4 4 BW3 BW4 VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A2 A3 5 BW2 BW1 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS DNU (3) 6 CE2 CLK VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC A1 A0 7 CEN R/ W VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD (1) 8 ADV/LD OE VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A10 A11 9 A17 NC(2) VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A13 A12 10 A8 A9 NC I/O15 I/O13 I/O11 I/O9 NC I/O7 I/O5 I/O3 I/O1 NC A14 A15 11 NC NC(2) I/OP2 I/O14 I/O12 I/O10 I/O8 ZZ I/O6 I/O4 I/O2 I/O0 I/OP1 NC A16 5304 tbl 25a DNU(3) DNU(3) DNU(3) DNU(3) Pin Configuration - 512K X 18, 165 fBGA 1 A B C D E F G H J K L M N P R NC(2) NC NC NC NC NC NC VDD(1) I/O12 I/O13 I/O14 I/O15 I/OP2 NC LBO 2 A7 A6 NC I/O8 I/O9 I/O10 I/O11 V DD(1) NC NC NC NC NC NC (2) 3 CE1 CE2 VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A5 A4 4 BW2 NC VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A2 A3 5 NC BW1 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS DNU DNU (3) (3) 6 CE2 CLK VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS NC A1 A0 7 CEN R/W VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS V DD (1) (3) 8 ADV /LD OE VSS VDD VDD VDD VDD VDD VDD VDD VDD VDD VSS A11 A12 9 A18 NC(2) VDDQ VDDQ VDDQ VDDQ VDDQ NC VDDQ VDDQ VDDQ VDDQ VDDQ A14 A13 10 A8 A9 NC NC NC NC NC NC I/O3 I/O2 I/O1 I/O0 NC A15 A16 11 A10 NC(2) I/OP1 I/O7 I/O6 I/O5 I/O4 ZZ NC NC NC NC NC NC A17 5304 tbl25b DNU NC(2) DNU(3) DNU(3) NOTES: 1. H1, H2, and N7 do not have to be directly connected to VDD as long as the input voltage is ≥ VIH. 2. B9, B11, A1, R2 and P2 is reserved for future 18M, 36M, 72M, 144M and 288M, respectively. 3. DNU=Do not use. Pins P5, R5, P7 and R7 are reserved for respective JTAG pins: TDI, TMS, TDO and TCK on future revisions. The current die revision allows these pins to be left unconnected, tied LOW (VSS), or tied HIGH (VDD). 6.42 8 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Synchronous Truth Table(1) CEN L L L L L L H R/W L H X X X X X Chip(5) Enable Select Select X X Deselect X X ADV/LD L L H H L H X BWx Valid X Valid X X X X ADDRESS USED External External Internal Internal X X X PREVIOUS CYCLE X X LOAD WRITE / BURST WRITE LOAD READ / BURST READ X DESELECT / NOOP X CURRENT CYCLE LOAD WRITE LOAD READ BURST WRITE (Advance burst counter)(2) BURST READ (Advance burst counter)(2) DESELECT or STOP(3) NOOP SUSPEND(4) I/O (2 cycles later) D(7) Q(7) D(7) Q(7) HiZ HiZ Previous Value 5304 tbl 08 NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. When ADV/LD signal is sampled high, the internal burst counter is incremented. The R/ W signal is ignored when the counter is advanced. Therefore the nature of the burst cycle (Read or Write) is determined by the status of the R/W signal when the first address is loaded at the beginning of the burst cycle. 3. Deselect cycle is initiated when either (CE1, or CE2 is sampled high or CE2 is sampled low) and ADV/LD is sampled low at rising edge of clock. The data bus will tri-state two cycles after deselect is initiated. 4. When CEN is sampled high at the rising edge of clock, that clock edge is blocked from propogating through the part. The state of all the internal registers and the I/ Os remains unchanged. 5. To select the chip requires CE1 = L, CE2 = L, CE2 = H on these chip enables. Chip is deselected if any one of the chip enables is false. 6. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up. 7. Q - Data read from the device, D - data written to the device. Partial Truth Table for Writes(1) OPERATION READ WRITE ALL BYTES WRITE BYTE 1 (I/O[0:7], I/OP1) (2) R/W H L L L L L L BW 1 X L L H H H H BW 2 X L H L H H H BW 3(3) X L H H L H H BW 4(3) X L H H H L H 5304 tbl 09 WRITE BYTE 2 (I/O[8:15], I/OP2)(2) WRITE BYTE 3 (I/O[16:23], I/OP3)(2,3) WRITE BYTE 4 (I/O[24:31], I/OP4) NO WRITE NOTES: 1. L = VIL, H = VIH, X = Don’t Care. 2. Multiple bytes may be selected during the same cycle. 3. N/A for X18 configuration. (2,3) 6.42 9 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Interleaved Burst Sequence Table (LBO=VDD) Sequence 1 A1 First Address Second Address Third Address Fourth Address (1) 0 0 1 1 A0 0 1 0 1 Sequence 2 A1 0 0 1 1 A0 1 0 1 0 Sequence 3 A1 1 1 0 0 A0 0 1 0 1 Sequence 4 A1 1 1 0 0 A0 1 0 1 0 5304 tbl 10 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. Linear Burst Sequence Table (LBO=VSS) Sequence 1 A1 First Address Second Address Third Address Fourth Address (1) 0 0 1 1 A0 0 1 0 1 Sequence 2 A1 0 1 1 0 A0 1 0 1 0 Sequence 3 A1 1 1 0 0 A0 0 1 0 1 Sequence 4 A1 1 0 0 1 A0 1 0 1 0 5304 tbl 11 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. Functional Timing Diagram(1) CYCLE CLOCK ADDRESS (A0 - A17) (2) n+29 n+30 n+31 n+32 n+33 n+34 n+35 n+36 n+37 A29 A30 A31 A32 A33 A34 A35 A36 A37 CONTROL (R/W, ADV/LD, BWx) (2) (2) C29 C30 C31 C32 C33 C34 C35 C36 C37 DATA I/O [0:31], I/O P[1:4] D/Q27 D/Q28 D/Q29 D/Q30 D/Q31 D/Q32 D/Q33 D/Q34 D/Q35 NOTES: 1. This assumes CEN, CE1, CE2, CE2 are all true. 2. All Address, Control and Data_In are only required to meet set-up and hold time with respect to the rising edge of clock. Data_Out is valid after a clock-to-data delay from the rising edge of clock. 5304 drw 03 , 6.42 10 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Device Operation - Showing Mixed Load, Burst, Deselect and NOOP Cycles(2) Cycle n n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8 n+9 n+10 n+11 n+12 n+13 n+14 n+15 n+16 n+17 n+18 n+19 Address A0 X A1 X X A2 X X A3 X A4 X X A5 A6 A7 X A8 X A9 R/W H X H X X H X X L X L X X L H L X H X L ADV/LD L H L L H L H L L H L L H L L L H L H L CE (1) L X L H X L X H L X L H X L L L X L X L CEN L L L L L L L L L L L L L L L L L L L L BWx X X X X X X X X L L L X X L X L L X X L OE X X L L L X X L L X X X X X X X L X X L I/O X X Q0 Q0+1 Q1 Z Z Q2 Q2+1 Z D3 D3+1 D4 Z Z D5 Q6 D7 D7+1 Q8 Comments Load read Burst read Load read Deselect or STOP NOOP Load read Burst read Deselect or STOP Load write Burst write Load write Deselect or STOP NOOP Load write Load read Load write Burst write Load read Burst read Load write 5304tbl 12 NOTES: 1. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 2. H = High; L = Low; X = Don’t Care; Z = High Impedance. Read Operation(1) Cycle n n+1 n+2 Address A0 X X R/W H X X ADV/LD L X X CE (2) L X X CEN L L X BWx X X X OE X X L I/O X X Q0 Comments Address and Control meet setup Clock Setup Valid Contents of Address A0 Read Out 5304 tbl 13 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 11 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Burst Read Operation(1) Cycle n n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8 Address A0 X X X X A1 X X A2 R/W H X X X X H X X H ADV/LD L H H H H L H H L CE (2) L X X X X L X X L CEN L L L L L L L L L BWx X X X X X X X X X OE X X L L L L L L L I/O X X Q0 Q0+1 Q0+2 Q0+3 Q0 Q1 Q1+1 Comments Address and Control meet setup Clock Setup Valid, Advance Counter Address A0 Read Out, Inc. Count Address A0+1 Read Out, Inc. Count Address A0+2 Read Out, Inc. Count Address A0+3 Read Out, Load A1 Address A0 Read Out, Inc. Count Address A1 Read Out, Inc. Count Address A1+1 Read Out, Load A2 5304 tbl 14 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance.. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Write Operation(1) Cycle n n+1 n+2 Address A0 X X R/ W L X X ADV/ LD L X X CE (2) L X X CEN L L L BWx L X X OE X X X I/O X X D0 Comments Address and Control meet setup Clock Setup Valid Write to Address A0 5304 tbl 15 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Burst Write Operation(1) Cycle n n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8 Address A0 X X X X A1 X X A2 R/W L X X X X L X X L ADV/LD L H H H H L H H L CE (2) L X X X X L X X L CEN L L L L L L L L L BWx L L L L L L L L L OE X X X X X X X X X I/O X X D0 D0+1 D0+2 D0+3 D0 D1 D1+1 Comments Address and Control meet setup Clock Setup Valid, Inc. Count Address A0 Write, Inc. Count Address A0+1 Write, Inc. Count Address A0+2 Write, Inc. Count Address A0+3 Write, Load A1 Address A0 Write, Inc. Count Address A1 Write, Inc. Count Address A1+1 Write, Load A2 5304 tbl 16 NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 12 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Read Operation with Clock Enable Used(1) Cycle n n+1 n+2 n+3 n+4 n+5 n+6 n+7 Address A0 X A1 X X A2 A3 A4 R/W H X H X X H H H ADV/LD L X L X X L L L CE (2) L X L X X L L L CEN L H L H H L L L BWx X X X X X X X X OE X X X L L L L L I/O X X X Q0 Q0 Q0 Q1 Q2 Comments Address and Control meet setup Clock n+1 Ignored Clock Valid Clock Ignored, Data Q0 is on the bus. Clock Ignored, Data Q0 is on the bus. Address A0 Read out (bus trans.) Address A1 Read out (bus trans.) Address A2 Read out (bus trans.) 5304 tbl 17 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Write Operation with Clock Enable Used(1) Cycle n n+1 n+2 n+3 n+4 n+5 n+6 n+7 Address A0 X A1 X X A2 A3 A4 R/W L X L X X L L L ADV/LD L X L X X L L L CE (2) L X L X X L L L CEN L H L H H L L L BWx L X L X X L L L OE X X X X X X X X I/O X X X X X D0 D1 D2 Comments Address and Control meet setup. Clock n+1 Ignored. Clock Valid. Clock Ignored. Clock Ignored. Write Data D0 Write Data D1 Write Data D2 5304 tbl 18 NOTES: 1. H = High; L = Low; X = Don’t Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 13 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Read Operation with Chip Enable Used(1) Cycle n n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8 n+9 Address X X A0 X A1 X X A2 X X R/ W X X H X H X X H X X ADV/ LD L L L L L L L L L L CE (2) H H L H L H H L H H CEN L L L L L L L L L L BWx X X X X X X X X X X OE X X X X L X L X X L I/O(3) ? ? Z Z Q0 Z Q1 Z Z Q2 Comments Deselected. Deselected. Address and Control meet setup Deselected or STOP. Address A0 Read out. Load A 1. Deselected or STOP. Address A1 Read out. Deselected. Address and control meet setup. Deselected or STOP. Address A2 Read out. Deselected. 5304 tbl 19 NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 3. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up. Write Operation with Chip Enable Used(1) Cycle n n+1 n+2 n+3 n+4 n+5 n+6 n+7 n+8 n+9 Address X X A0 X A1 X X A2 X X R/W X X L X L X X L X X ADV/LD L L L L L L L L L L CE (2) H H L H L H H L H H CEN L L L L L L L L L L BWx X X L X L X X L X X OE X X X X X X X X X X I/O(3) ? ? Z Z D0 Z D1 Z Z D2 Comments Deselected. Deselected. Address and Control meet setup Deselected or STOP. Address D0 Write in. Load A 1. Deselected or STOP. Address D1 Write in. Deselected. Address and control meet setup. Deselected or STOP. Address D2 Write in. Deselected. 5304 tbl 20 NOTES: 1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 6.42 14 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V +/-5%) Symbol |ILI| |ILI| |ILO| VOL VOH Parameter Input Leakage Current LBO Input Leakage Current(1) Output Leakage Current Output Low Voltage Output High Voltage Test Conditions VDD = Max., VIN = 0V to V DD VDD = Max., VIN = 0V to V DD VOUT = 0V to V DDQ , Device Deselected IOL = +8mA, VDD = Min. IOH = -8mA, VDD = Min. Min. ___ Max. 5 30 5 0.4 ___ Unit µA µA µA V V ___ ___ ___ 2.4 NOTE: 5304 tbl 21 1. The LBO pin will be internally pulled to VDD if it is not actively driven in the application and the ZZ pin will be internally pulled to Vss if not actively driven. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1) (VDD = 3.3V +/-5%) 150MHz Symbol IDD Parameter Operating Power Supply Current Test Conditions Device Selected, Outputs Open, ADV/LD = X, VDD = Max., VIN > VIH o r < VIL, f = fMAX(2) Device Deselected, Outputs Open, VDD = Max., VIN > VHD o r < VLD, f = 0(2,3) Device Deselected, Outputs Open, VDD = Max., VIN > VHD o r < VLD, f = fMAX(2.3) Device Selected, Outputs Open, CEN > VIH, VDD = Max., VIN > VHD o r < VLD, f = fMAX(2,3) Device Selected, Outputs Open CEN ≤ VIL, VDD = Max., ZZ ≥ VHD VIN ≥ VHD o r ≤ VLD, f = fMax (2,3) Com'l 325 Ind 345 133MHz Com'l 300 Ind 320 100MHz Com'l 250 Ind mA 270 Unit ISB1 CMOS Standby Power Supply Current mA 40 60 40 60 40 60 ISB2 Clock Running Power Supply Current mA 120 140 110 130 100 120 ISB3 Idle Power Supply Current mA 40 60 40 60 40 60 IZZ Full Sleep Mode Supply Current 40 60 40 60 40 60 mA 5304 tbl 22 NOTES: 1. All values are maximum guaranteed values. 2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC; f=0 means no input lines are changing. 3. For I/Os VHD = VDDQ – 0.2V, VLD = 0.2V. For other inputs VHD = VDD – 0.2V, VLD = 0.2V. AC Test Load I/O 6 5 4 ∆tCD 3 (Typical, ns) 2 1 VDDQ/2 50Ω Z0 = 50Ω 5304 drw 04 AC Test Conditions (VDDQ = 3.3V) , Input Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Timing Reference Levels AC Test Load 0 to 3V 2ns 1.5V 1.5V See Figure 1 5304 tbl 23 Figure 1. AC Test Load • • • •• 80 100 Capacitance (pF) 200 5304 drw 05 20 30 50 , Figure 2. Lumped Capacitive Load, Typical Derating 6.42 15 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges AC Electrical Characteristics Symbol Parameter (VDD = 3.3V +/-5%, Commercial and Industrial Temperature Ranges) 150MHz(6) Min. Max. 133MHz Min. Max. 100MHz Min. Max. Unit tCYC tF (1) (2) Clock Cycle Time Clock Frequency Clock High Pulse Width Clock Low Pulse Width 6.7 ____ ____ 7.5 ____ ____ 10 ____ ____ ns MHz ns ns 150 ____ 133 ____ 100 ____ tCH 2.0 2.0 2.2 2.2 3.2 3.2 tCL(2) ____ ____ ____ Output Parameters tCD tCDC tCLZ (3,4,5) (3,4,5) Clock High to Valid Data Clock High to Data Change Clock High to Output Active Clock High to Data High-Z Output Enable Access Time (3,4) ____ 3.8. ____ ____ 4.2 ____ ____ 5 ____ ns ns ns ns ns ns ns 1.5 1.5 1.5 ____ 1.5 1.5 1.5 ____ 1.5 1.5 1.5 ____ ____ ____ ____ tCHZ tOE tOLZ 3 3.8 ____ 3 4.2 ____ 3.3 5 ____ Output Enable Low to Data Active Output Enable High to Data High-Z 0 ____ 0 ____ 0 ____ tOHZ(3,4) 3.8 4.2 5 Set Up Times tSE tSA tSD tSW tSADV tSC tSB Hold Times tHE tHA tHD tHW tHADV tHC tHB Clock Enable Hold Time Address Hold Time Data In Hold Time Read/Write (R/ W) Hold Time Advance/Load (ADV/ LD) Hold Time Chip Enable/Select Hold Time Byte Write Enable (BWx) Hold Time 0.5 0.5 0.5 0.5 0.5 0.5 0.5 ____ ____ ____ ____ ____ ____ ____ Clock Enable Setup Time Address Setup Time Data In Setup Time Read/Write (R/ W) Setup Time Advance/Load (ADV/ LD) Setup Time Chip Enable/Select Setup Time Byte Write Enable (BWx) Setup Time 1.5 1.5 1.5 1.5 1.5 1.5 1.5 ____ ____ ____ ____ ____ ____ ____ 1.7 1.7 1.7 1.7 1.7 1.7 1.7 ____ ____ ____ ____ ____ ____ ____ 2.0 2.0 2.0 2.0 2.0 2.0 2.0 ____ ____ ____ ____ ____ ____ ____ ns ns ns ns ns ns ns 0.5 0.5 0.5 0.5 0.5 0.5 0.5 ____ ____ ____ ____ ____ ____ ____ 0.5 0.5 0.5 0.5 0.5 0.5 0.5 ____ ____ ____ ____ ____ ____ ____ ns ns ns ns ns ns ns 5304 tbl 24 NOTES: 1. tF = 1/tCYC. 2. Measured as HIGH above 0.6VDDQ and LOW below 0.4VDDQ. 3. Transition is measured ±200mV from steady-state. 4. These parameters are guaranteed with the AC load (Figure 1) by device characterization. They are not production tested. 5. To avoid bus contention, the output buffers are designed such that tCHZ (device turn-off) is about 1ns faster than tCLZ (device turn-on) at a given temperature and voltage. The specs as shown do not imply bus contention because tCLZ is a Min. parameter that is worse case at totally different test conditions (0 deg. C, 3.465V) than tCHZ, which is a Max. parameter (worse case at 70 deg. C, 3.135V). 6. Commercial temperature range only. 6.42 16 tCYC CLK tSE tHE tCH tCL CEN tHADV tSADV ADV/LD tSW tHW R/W tSA tHA A2 tSC tHC ADDRESS A1 CE1, CE2 (2) Timing Waveform of Read Cycle(1,2,3,4) IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 6.42 17 tCLZ tCD Q(A1) Pipeline Read Pipeline Read Q(A2) O1(A2) tCDC O2(A2) Q(A2+1) tCDC tCD (CEN high, eliminates current L-H clock edge) (Burst Wraps around to initial state) BW1 - BW4 OE tCHZ Q(A2+2) Burst Pipeline Read 5304 drw 06 DATAOUT Q(A2+2) Q(A2+3) O1(A2) Q(A2) NOTES: 1. Q (A1) represents the first output from the external address A1. Q (A2) represents the first output from the external address A2; Q (A2+1) represents the next output data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are loaded into the SRAM. , tCYC CLK tSE tHE tCH tCL CEN tHADV tSADV ADV/LD tSW tHW R/W tSA tHA A2 tSC tHC ADDRESS A1 CE1, CE2 tSB tHB (2) Timing Waveform of Write Cycles(1,2,3,4,5) IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 6.42 18 tSD tHD D(A2) D(A1) Pipeline Write Pipeline Write BW1 - BW4 OE (CEN high, eliminates current L-H clock edge) tSD D(A2+1) Burst Pipeline Write tHD D(A2+2) (Burst Wraps around to initial state) DATAIN D(A2+3) D(A2) 5304 drw 07 NOTES: 1. D (A1) represents the first input to the external address A1. D (A2) represents the first input to the external address A2; D (A2+1) represents the next input data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/ W signal when new address and control are loaded into the SRAM. 5. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. . tCYC CLK tSE tHE tCH tCL CEN tHADV tSADV ADV/LD tSW tHW R/W tSA tHA A2 A3 A6 A4 A5 A7 tSC tHC tSB tHB A8 A9 ADDRESS A1 CE1, CE2(2) Timing Waveform of Combined Read and Write Cycles(1,2,3) IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 6.42 19 tSD tHD D(A2) Write tCD Q(A1) Read Read tCHZ tCLZ Q(A3) Write tCDC D(A4) BW1 - BW4 OE DATAIN D(A5) DATAOUT Q(A6) Read Q(A7) 5304 drw 08 NOTES: 1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. , , tCYC CLK tSE tHE tCH tCL CEN tSADV tHADV ADV/LD tSW tHW R/W tSA tHA A2 A3 tSC tHC A4 A5 ADDRESS A1 CE1, CE2(2) tSB tHB B(A2) Timing Waveform of CEN Operation(1,2,3,4) IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 6.42 20 tCHZ tCD Q(A1) tCLZ tCDC Q(A1) BW1 - BW4 OE tSD tHD D(A2) DATAIN DATAOUT Q(A3) 5304 drw 09 NOTES: 1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propogating into the SRAM. The part will behave as if the L-H clock transition did not occur. All internal registers in the SRAM will retain their previous state. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. tCYC CLK tSE tHE tCH tCL CEN tSADV tHADV ADV/LD tSW tHW R/W tSA A1 tSC tHC tHA A2 A3 A4 A5 ADDRESS CE1, CE2 tSB tHB (2) Timing Waveform of CS Operation(1,2,3,4) IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 6.42 21 tCHZ tCD tCLZ Q(A1) tCDC Q(A2) BW1 - BW4 OE tSD tHD D(A3) DATAIN DATAOUT Q(A4) 5304 drw 10 NOTES: 1. Q (A1) represents the first output from the external address A1. D (A3) represents the input data to the SRAM corresponding to address A3. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propogating into the SRAM. The part will behave as if the L-H clock transition did not occur. All internal registers in the SRAM will retain their previous state. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. , IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 100-Pin Plastic Thin Quad Flatpack (TQFP) Package Diagram Outline 6.42 22 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 119 Ball Grid Array(BGA) Package Diagram Outline 6.42 23 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges 165 Fine Pitch Ball Grid Array (fBGA) Package Diagram Outline 6.42 24 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMS with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Timing Waveform of OE Operation(1) OE tOE tOHZ tOLZ Valid DATAOUT , NOTE: 1. A read operation is assumed to be in progress. 5304 drw 11 Ordering Information IDT XXXX Device Type S Power XX Speed XX Package X Process/ Temperature Range Blank I PF BG BQ 150 133 100 Commerical (0° to 70°C) Industrial (-40° to 85°C) 100 pin Plastic Thin Quad Flatpack, (TQFP) 119 Ball Grid Array (BGA) 165 Fine Pitch Ball Grid Array (fBGA) Clock Frequency in Megahertz 5304 drw 12 IDT71V65603 IDT71V65803 256Kx36 Pipelined ZBT SRAM 512Kx18 Pipelined ZBT SRAM CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com for Tech Support: sramhelp@idt.com 800-544-7726, x4033 The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 25 IDT71V65603, IDT71V65803, 256K x 36, 512K x 18, 3.3V Synchronous SRAMs with ZBT™ Feature, 3.3V I/O, Burst Counter, and Pipelined Outputs Commercial and Industrial Temperature Ranges Datasheet Document History 12/31/99 03/04/00 04/20/00 Created new datasheet from obsolete devices IDT71V656 and IDT71V658 Removed 166MHz speed grade offering; Added 150MHz speed grade offering Added JTAG test pins to TQFP pin configuration; removed footnote Add clarification note to Recommended Operating temperature and Absolute Max Ratings tables Add note to BGA pin Configuration; correct typo within pinout Insert TQFP Package Diagram Outline Add new package offering, 13 x 15mm 165 fBGA Pg. 23 Correction in BG 119 Package Diagram Outline Add industrial temperature Pg. 2 Correction VDDQ 3.3V I/O supply Pg. 5-8 Remove JTAG offerings, refer to IDT71V656xx and IDT71V658xx device errata sheet Pg. 7 Correct pin B2 Pg. 8 Change pin B1 to NC Pg. 23 Update BG119 Package Diagram Outline Pg. 8 Add note to pin N5 on BQ165 pinout, reserved for JTAG TRST Pg. 15 Add Izz parameter to DC Electrical Characteristics Pg. 16 Changed sub-header to include Commercial and Industrial Temperature Ranges. Corrected the TCH from 22ns to 2.2ns and TSADV from 20ns to 2.0ns. Pg. 1-25 Changed datasheet from Prelininary to final release. Pg. 15 Added I temp to 150MHz. Pg. 16 Corrected typo from 22 to 2.2. Pg. 1,2,5,6, Removed JTAG functionality for current die revision. 7,8 Pg. 7 Corrected pin configuration on the x36, 119BGA. Switched pins I/O0 and I/OP1. Pg. 1,14,15 Pg. 5,6 Pg. 5,6 Pg. 7 Pg. 21 05/23/00 07/28/00 11/04/00 10/16/01 12/04/02 12/19/02 6.42 26