1ED020I12FA

Datasheet, Version 2.1, November 2009 EICEDRIVER® 1ED020I12FA Single IGBT Driver IC Power Management & Drives Never stop thinking. 1ED020I12FA Revision History: Previous Version: Page 14 2009-11-24 2.0 Version 2.1 Subjects (major changes since last revision) Update table No 4.4.6 Dynamic Characteristics Edition 2009-11-24 Published by Infineon Technologies AG, Campeon 1-12, 85579 Neubiberg, Germany © Infineon Technologies AG 2009. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. EICEDRIVER® 1ED020I12FA Single IGBT Driver IC Product Highlights • • • • • • Coreless transformer isolated driver Galvanic Insulation Integrated protection features Suitable for operation at high ambient temperature Cost effective technology Automotive Qualified Features • • • • • Single channel isolated IGBT Driver For 600V/1200V IGBTs 2A rail-to-rail output Vcesat-detection Active Miller Clamp Typical Application • • • • AC and Brushless DC Motor Drives High Voltage DC/DC-Converter UPS-Systems Welding VCC1 VCC2,H DESAT IN+, IN-, /RST EiceDRIVERTM /FLT, RDY CLAMP 1ED020I12FA OUT VEE2,H GND2,H CPU VCC2,L DESAT IN+, IN-, /RST EiceDRIVER /FLT, RDY CLAMP TM 1ED020I12FA OUT GND1 VEE2,L GND2,L Figure 1: Typical Application Type 1ED020I12FA Datasheet Gate drive current +/- 2A 3 Package PG-DSO-20-55 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Table of Contents 1 2 2.1 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.3 2.4 2.5 2.5.1 2.5.2 2.5.3 2.6 3 3.1 3.2 4 4.1 4.2 4.3 4.4 4.4.1 4.4.2 4.4.3 4.4.4 4.4.5 4.4.6 4.4.7 4.4.8 5 5.1 5.2 5.3 6 7 8 8.1 8.2 Page 6 6 6 6 6 6 6 6 6 7 7 7 7 7 Blockdiagram and Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Undervoltage Lockout (UVLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . READY status output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Shut-Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-Inverting and Inverting Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Driver Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Desaturation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Miller Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Configuration and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electrical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltage Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Logic Input and Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gate Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Miller Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short Circuit Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dynamic Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Desaturation protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Active Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Insulation Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . According to DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01. Basic Insulation . . . . . . . . . . . . . . . . . . . . . . . . According to UL 1577) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 11 11 12 12 12 13 13 13 14 14 15 16 16 16 16 Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Reference Layout for Thermal Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Printed Circuit Board Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Datasheet 4 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA 1 GND1 Blockdiagram and Application 11 K4 2V 10 VEE2 GND1 12 CLAMP 9 VEE2 IN+ 0 & 0 13 ∆t 0 8 CLAMP /RST IN14 ∆t LOGIC TX RX VCC2 LOGIC RDY_LOOP VEE2 7 VEE2 OUT /FLT RDY 15 6 VCC2 UVLO /FLT 16 UVLO 5 NC /RST 17 4 GND2 LOGIC VCC1 18 RX TX LOGIC DESAT K3 9V I3 3 R DESAT GND1 19 GND2 2 VEE2 GND1 20 1 VEE2 Figure 2: Blockdiagram 1ED020I12FA 1ED020I12FA Figure 3: Application example Datasheet 5 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA 2 2.1 Functional Description Introduction 2.2.2 READY status output The READY output shows the status of three internal protection features. • • • UVLO of the input chip UVLO of the output chip after a short delay Internal signal transmission The 1ED020I12FA is an advanced IGBT gate driver that can be also used for driving power MOS devices. Control and protection functions are included to make possible the design of high reliability systems. The device consists of two galvanic separated parts. The input chip can be directly connected to a standard 5V DSP or microcontroller with CMOS in/output and the output chip is connected to the high voltage side. An effective active Miller clamp function avoids the need of negative gate driving in most applications and allows the use of a simple bootstrap supply for the high side driver. A rail-to-rail driver output enables the user to provide easy clamping of the IGBTs gate voltage during short circuit of the IGBT. So an increase of short circuit current due to the feedback via the Miller capacitance can be avoided. Further, a rail-to-rail output reduces power dissipation. The device also includes an IGBT desaturation protection with a FAULT status output. A READY status output reports if the device is supplied and operates correctly. It is not necessary to reset the READY signal since its state only depends on the status of the former mentioned protection signals. 2.2.3 Watchdog Timer The 1ED020I12FA incorporates two level of signal transmission security implemented through two independent watchdog timers. First level ensures the short term signal integrity by resending the (turn on/off) signals with a watchdog period of typical 500ns. The second level monitors during normal operation the internal signal transmission. If the transmission fails for a given time, the IGBT is switched off and the READY output reports an internal error. 2.2.4 Active Shut-Down The Active Shut-Down feature ensures a safe IGBT off-state if the output chip is not connected to the power supply. 2.2 2.2.1 Internal Protection Features Undervoltage Lockout (UVLO) 2.3 Non-Inverting and Inverting Inputs To ensure correct switching of IGBTs the device is equipped with an undervoltage lockout for both chips. If the power supply voltage VVCC1 of the input chip drops below VUVLOL1 a turn-off signal is sent to the output chip before power-down. The IGBT is switched off and the signals at IN+ and IN- are ignored as long as VVCC1 reaches the power-up voltage VUVLOH1 . If the power supply voltage VVCC2 of the output chip goes down below VUVLOL2 the IGBT is switched off and signals from the input chip are ignored as long as VVCC2 reaches the power-up voltage VUVLOH2 . There are two possible input modes to control the IGBT. At non-inverting mode IN+ controls the driver output while INis set to low. At inverting mode IN- controls the driver output while IN+ is set to high. A minimum input pulse width is defined to filter occasional glitches. 2.4 Driver Output The output driver section uses only MOSFETs to provide a rail-to-rail output. This feature permits that tight control of gate voltage during on-state and short circuit can be maintained as long as the drivers supply is stable. Due to the low internal voltage drop, switching behaviour of the IGBT is predominantly governed by the gate resistor. Furthermore, it reduces the power to be dissipated by the driver. Datasheet 6 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA 2.5 2.5.1 External Protection Features Desaturation Protection A desaturation protection ensures the protection of the IGBT at short circuit. When the DESAT voltage goes up and reaches 9V, the output is driven low. Further, the FAULT output is activated until it is cleared by /RST. A programmable blanking time is used to allow enough time for IGBT saturation. Blanking time is provided by a highly precise internal current source and an external capacitor. 2.5.2 Active Miller Clamping A Miller clamp allows sinking the Miller current during a high dV/dt situation. Therefore, the use of a negative supply voltage can be avoided in many applications. During turnoff, the gate voltage is monitored and the clamp output is activated when the gate voltage goes below 2V (related to VEE2). The clamp is designed for a Miller current up to 1A. 2.5.3 Short Circuit Clamping During short circuit the IGBTs gate voltage tends to rise because of the feedback via the Miller capacitance. An additional protection circuit connected to OUT and CLAMP limits this voltage to a value slightly higher than the supply voltage. A current of maximum 500 mA for 10us may be fed back to the supply through one of this paths. If higher currents are expected or a tighter clamping is desired external Schottky diodes may be added. 2.6 RESET The reset input has two functions. Firstly, /RST is in charge of setting back the FAULT output. If /RST is low longer than a given time , /FLT will be reseted at the rising edge of /RST; otherwise, it will remain unchanged. Moreover, it works as enable/shutdown of the input logic. Datasheet 7 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA 3 3.1 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 VEE2 VEE2 Pin Configuration and Functionality Pin Configuration Symbol Function Negative power supply output side Negative power supply output side Desaturation protection Signal ground output side Not connected Positive power supply output side Driver output Miller clamping Negative power supply output side Negative power supply output side Signal ground input side Signal ground input side Non inverted driver input Inverted driver input Ready output Fault output Reset input Positive power supply input side Signal ground input side Signal ground input side Figure 4: PG-DSO-20-55 1 2 3 4 5 6 7 8 9 VEE2 VEE2 DESAT GND2 NC VCC2 OUT CLAMP VEE2 GND1 20 GND1 19 VCC1 18 /RST 17 /FLT 16 RDY 15 IN- 14 IN+ 13 GND1 12 GND1 11 DESAT GND2 NC VCC2 OUT CLAMP VEE2 VEE2 GND1 GND1 IN+ INRDY FLT RST VCC1 GND1 GND1 10 VEE2 3.2 Pin Functionality GND1 Ground connection of the input side. IN+ Non-inverting driver input IN+ control signal for the driver output if IN- is set to low. (The IGBT is on if IN+ = high and IN- = low) A minimum pulse width is defined to make the IC robust against glitches at IN+. An internal Pull-Down-Resistor ensures IGBT Off-State. IN- Inverting driver input IN- control signal for driver output if IN+ is set to high. (IGBT is on if IN- = low and IN+ = high) A minimum pulse width is defined to make the IC robust against glitches at IN-. An internal Pull-Up-Resistor ensures IGBT Off-State. /RST (Reset) input Function 1: Enable/shutdown of the input chip. (The IGBT is off if /RST = low). A minimum pulse width is defined to make the IC robust against glitches at IN-. Datasheet 8 Function 2: Resets the DESAT-FAULT-state of the chip if /RST is low for a time TRST. An internal Pull-Up-Resistor is used to ensure FLT status output. /FLT (Fault output) Open-drain output to report a desaturation error of the IGBT (FLT is low if desaturation occurs) RDY (Ready status) Open-drain output to report the correct operation of the device. (RDY = high if both chips are above the UVLO level and the internal chip transmission is faultless) VCC1 5V power supply of the input chip VEE2 Negative power supply pins of the output chip. If no negative supply voltage is available, both pins have to be connected to GND2. Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA DESAT (Desaturation) Monitoring of the IGBT saturation voltage (VCE) to detect desaturation caused by short circuits. If OUT is high, VCE is above a defined value and a certain blanking time has expired, the desaturation protection is activated and the IGBT is switched off. The blanking time is adjustable by an external capacitor. CLAMP (Clamping) Ties the gate voltage to VEE2 after the IGBT has been switched off at a defined voltage to avoid a parasitic switchon of the IGBT.During turn-off, the gate voltage is monitored and the clamp output is activated when the gate voltage goes below 2V (related to VEE2). GND2 Reference ground of the output chip. OUT (Driver output) Output pin to drive an IGBT. The voltage is switched between VEE2 and VCC2. In normal operating mode Vout is controlled by IN+, IN- and /RST. During error mode (UVLO, internal error or DESAT) Vout is set to VEE2 independent of the input control signals. VCC2 Positive power supply pin of the output side. Datasheet 9 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Electrical Parameters 4 4.1 Electrical Parameters Absolute Maximum Ratings Note: Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of the integrated circuit. Unless otherwise noted all parameters refer to GND1. Parameter Positive power supply output side Negative power supply output side Maximum power supply voltage output side (VVCC2-VVEE2) Gate driver output Gate driver high output maximum current Gate & Clamp driver low output maximum current Maximum short circuit clamping time Positive power supply input side Logic input voltages (IN+,IN-,RST) Opendrain Logic output voltage (FLT) Opendrain Logic output voltage (RDY) Opendrain Logic output current (FAULT) Opendrain Logic output current (RDY) Pin DESAT voltage Pin CLAMP voltage Junction temperature Storage temperature Power dissipation, Input chip Power dissipation, Output chip Thermal resistance (Input chip active) Thermal resistance (Output chip active) ESD Capability 1) With respect to GND2. 2) may be exceeded during short circuit clamping 3) Output IC power dissipation is derated linearly at 8.5 mW/°C above 68°C. Input IC power dissipation does not require derating. See section 8.1 for reference layouts for these thermal data. Thermal performance may change significantly with layout and heat dissipation of components in close proximity. 4) According to EIA/JESD22-A114-B (discharging a 100pF capacitor through a 1.5kΩ series resistor). Symbol VVCC2 VVEE2 Vmax2 VOUT IOUT IOUT tCLP VVCC1 VLogicIN VFLT VRDY IFLT IRDY VDESAT VCLAMP TJ TS PD, IN PD, OUT RTHJA,IN RTHJA,OUT VESD Limit Values min. -0.3 -12 max. 20 0.3 28 Vmax2+0.3 2.4 2.4 Unit Remarks V V V V A A us V V V V mA mA 1) 1) 1)  VVEE2-0.3 t = 2µs t = 2µs ICLAMP/OUT = 500mA  -0.3 -0.3 -0.3 -0.3 10 6.5 6.5 6.5 6.5 10 10 VVCC2 +0.3 VVCC2+0.3 2)   -0.3 VVEE2-0.3 -40 -55 VVEE2 = -8V 150 150 100 700 139 117 1 °C °C mW mW K/W K/W kV 3)      @TA = 25° @TA = 25° @TA = 25°C @TA = 25°C 2)3) 2) 2) Human Body Model4) Datasheet 10 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Electrical Parameters 4.2 Operating Parameters Note: Within the operating range the IC operates as described in the functional description. Unless otherwise noted all parameters refer to GND1. Parameter Positive power supply output side Negative power supply output side Maximum power supply voltage output side (VVCC2-VVEE2) Positive power supply input side Logic input voltages (IN+,IN-,RST) Pin CLAMP voltage Pin DESAT voltage Ambient temperature Common mode transient immunity 1) With respect to GND2. 2) may be exceeded during short circuit clamping 3) The parameter is not subject to production test - verified by design/characterization 3) Symbol VVCC2 VVEE2 Vmax2 VVCC1 VLogicIN VCLAMP VDESAT TA |∆VISO/dt| Limit Values min. 13 -12 max. 20 0 28 5.5 5.5 VVCC22) VVCC2 125 50 Unit V V V V V V V °C Remarks 1) 1)  4.5 -0.3 VVEE2-0.3 -0.3 -40 — 1) kV/µs @ 500V 4.3 Parameter Recommended Operating Parameters Symbol VVCC2 VVEE2 VVCC1 Values 15 -8 5 Unit Remarks V V V 1) 1) Note: Unless otherwise noted all parameters refer to GND1. Positive power supply output side Negative power supply output side Positive power supply input side 1) With respect to GND2. Datasheet 11 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Electrical Parameters 4.4 Electrical Characteristics Note: The electrical characteristics involve the spread of values for the supply voltages, load and junction temperature range from -40°C to +150°C. Typical values represent the median values, which are related to production processes at TJ = 25°C. Unless otherwise noted all voltages are given with respect to GND. 4.4.1 Parameter Voltage Supply. Symbol VUVLOH1 VUVLOL1 3.5 0.15 VHYS1 VUVLOH2 VUVLOL2 VHYS2 IQ1 0.7 Limit Values min. typ. 4.1 3.8 max. 4.3 V Unit Test Conditions UVLO Threshold Input Chip UVLO Hysteresis Input Chip (VUVLOH1 - VUVLOL1) UVLO Threshold Output Chip UVLO Hysteresis Output Chip (VUVLOH1 - VUVLOL1) Quiescent Current Input Chip   12.0 11.0 0.9   12.6 V V V V V mA VVCC1 =5V IN+ = High, IN- = Low =>OUT = High, RDY = High, /FLT = High VVCC2 =15V VVEE2 =-8V IN+ = High, IN- = Low =>OUT = High, RDY = High, /FLT = High  10.4   9  7 Quiescent Current Output Chip IQ2  4 6 mA 4.4.2 Parameter Logic Input and Output Symbol VIN+L,VINL,VRSTL VIN+H,VIN- 3.5 HVRSTH IIN-,IRST IIN+, IPRDY, IPFLT TMININ+, TMININTMINRST TRST VFLTL VRDYL 30 30 800 Limit Values min. typ. max. 1.5 V Unit Test Conditions IN+,IN-, RST Low Input Voltage IN+,IN-, RST High Input Voltage IN-, RST Input Current IN+ Input Current RDY,FLT Pull Up Current Input Pulse Suppression IN+, INInput Pulse Suppression RST for ENABLE/SHUTDOWN Pulse Width RST for Reseting FLT FLT Low Voltage RDY Low Voltage     400 400 400 V uA uA uA VIN-=GND1 VRST =GND1 VIN+=VCC1 VRDY=GND1 VFLT=GND1    100 100 100 40 40     300 300 ns ns ns mV mV ISINK(FLT) = 5mA ISINK(RDY) = 5mA Version 2.1, 2009-11-24   12   Datasheet EICEDRIVER® 1ED020I12FA Electrical Parameters 4.4.3 Parameter Gate Driver Symbol min. VOUTH1 VOUTH2 VOUTH3 VOUTH4 VVCC2-1.2 VVCC2-2.5 VVCC2-9 -1.5 Limit Values typ. VVCC2-0.8 VVCC2-2 VVCC2-5 VVCC2-10 -2 max. Unit Test Conditions High Level Output Voltage High Level Output Peak Current Low Level Output Voltage IOUTH VOUTL1 VOUTL2 VOUTL3 VOUTL4      V V V V A V V V V A IOUTH = -20mA IOUTH = -200mA IOUTH = -1A IOUTH = -2A IN+ = High, IN- = Low; OUT = High IOUTL = 20mA IOUTL = 200mA IOUTL = 1A IOUTL = 2A IN+ = Low, IN- = Low; OUT = Low, VVCC2 =15V, VVEE2 =-8V     1.5 VVEE2+0.04 VVEE2 +0.09 VVEE2+0.3 VVEE2+2.1 VVEE2+7 2 VVEE2 +0.85 VVEE2 +5.0 — — Low Level Output Peak Current IOUTL 4.4.4 Parameter Active Miller Clamp Symbol min. VCLAMPL1 VCLAMPL2 VCLAMPL3 Limit Values typ. VVEE2+0.3 VVEE2+1.9 2 1.6 max. IOUTL = 20mA IOUTL = 200mA IOUTL = 1A 1) Unit Test Conditions Low Level Clamp Voltage VVEE2+0.03 VVEE2 +0.08 V VVEE2 +0.8 VVEE2 +4.8 V V A V Low Level Clamp Current Clamp Threshold Voltage ICLAMPL VCLAMP  2.1  2.4 Related to VEE2 1) The parameter is not subject to production test - verified by design/characterization 4.4.5 Parameter Short Circuit Clamping Symbol VCLPout Limit Values min. typ. 0.8 max. 1.3 V IN+=High, IN-=Low, OUT=High IOUT = 500mA (pulse test,tCLPmax=10us) IN+=High, IN-=Low, OUT=High ICLAMP = 500mA (pulse test,tCLPmax=10us) IN+=High, IN-=Low, OUT=High ICLAMP = 20mA Unit Test Conditions Clamping voltage (OUT) (VOUT-VVCC2)  Clamping voltage (CLAMP) (VVCLAMP-VVCC2) VCLPclamp  1.3  V Clamping voltage (CLAMP) VCLPclamp  0.7 1.1 V Datasheet 13 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Electrical Parameters 4.4.6 Parameter Dynamic Characteristics Symbol TPDON TPDOFF TPDISTO TPDONt TPDOFFt TPDISTOt TPDONt TPDOFFt TPDISTOt TRISE Limit Values min. typ. 185 165 -20 190 190 0 190 160 -30 30 max. 7501) 185 555 1) Unit Test Conditions ns ns ns ns ns ns ns ns ns ns VVCC1 =5V VVCC2 =15V,VVEE2 =-8V CLOAD= 100pF VIN+=50%, VOUT=50% @ TA =25°C VVCC1 =5V VVCC2 =15V,VVEE2 =-8V CLOAD= 100pF VIN+=50%, VOUT=50% @ TA =125°C VVCC1 =5V VVCC2 =15V,VVEE2 =-8V CLOAD= 100pF VIN+=50%, VOUT=50% @ TA =-40°C VVCC2 =15V,VVEE2 =-8V CLOAD= 1nF VL 10% ,VH 90% VVCC2 =15V,VVEE2 =-8V CLOAD= 34nF VL 10% ,VH 90% VVCC2 =15V,VVEE2 =-8V CLOAD= 1nF VL 10% ,VH 90% VVCC2 =15V,VVEE2 =-8V CLOAD= 34nF VL 10% ,VH 90% Input to output propagation delay ON Input to output propagation delay OFF Input to output propagation delay distortion Input to output propagation delay ON variation due to temp Input to output propagation delay OFF variation due to temp Input to output propagation delay distortion variation due to temp Input to output propagation delay ON variation due to temp Input to output propagation delay OFF variation due to temp Input to output propagation delay distortion variation due to temp Rise Time 160 145 -50 160 160 -30 160 130 -60 10 990 1) 220 800 1) 990 1) 190 770 1) 60 200 400 800 ns Fall Time TFALL 10 50 90 ns 200 450 600 ns 1) The maximum value of input to output propagation delay ON occures only in case of electromagnetic interferences, typically the input to output delay is 205ns at TA =25°C, one worst case watchdog clock cycle shorter (see chapter 2.2.3). The turn OFF-signal is prioritized/dominant and will not show up this behavior. Datasheet 14 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Electrical Parameters 4.4.7 Parameter Desaturation protection Symbol IDESATC IDESATD VDESAT VDESAT TDESATOUT TDESATFLT VDESATL Limit Values min. typ. 250 2 9 8.6 100 max. 275 uA VVCC2 =15V,VVEE2 =-8V VDESAT=2V 225 1 8.3 7.6 Unit Test Conditions Blanking Capacitor Charge Current Blanking Capacitor Discharge Current Desaturation Reference Level Desaturation Reference Level Desaturation Sense to OUT Low Delay Desaturation Sense to FLT Low Delay Desaturation Low Voltage  9.5 9.5 150 2.25 mA VVCC2 =15V,VVEE2 =-8V VDESAT=6V V V ns us V VVCC2 =15V,VVEE2 =-8V VVCC2 =15V,VVEE2 =0V VOUT =90% CLOAD= 1nF VFLT =10%; IFLT =5mA IN+=Low, IN-=Low, OUT=Low   0.4 0.6 0.95 4.4.8 Parameter Active Shut Down Symbol VACTSD 1) Limit Values min. typ. max. 4 Unit Test Conditions Active Shut Down Voltage 1) With reference to VEE2   V IOUT=-200mA, VCC2 open Datasheet 15 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Insulation Characteristics 5 5.1 Description Insulation Characteristics Complies with DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01. Basic Insulation Symbol Characteristic I-IV I-III I-II 40/125/21 2 CLR CPG CTI VIORM VIOTM VIOSM 8 8 175 1420 6000 6000 VPEAK VPEAK V mm mm Unit Installation classification per EN 60664-1, Table 1 for rated mains voltage ≤ 150 VRMS for rated mains voltage ≤ 300 VRMS for rated mains voltage ≤ 600 VRMS Climatic Classification Pollution Degree (EN 60664-1) Minimum External Clearance Minimum External Creepage Minimum Comparative Tracking Index Maximum Repetitive Insulation Voltage Highest Allowable Overvoltage 1) Maximum Surge Insulation Voltage 5.2 Description Complies with UL 1577 Symbol VISO VISO Characteristic 3750 4500 Unit Vrms Vrms Insulation Withstand Voltage / 1min Insulation Test Voltage / 1sec 5.3 Reliability For Qualification Report please contact your local Infineon Technologies office. Datasheet 16 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Timing Diagrams 6 Timing Diagrams IN OUT TPDELAY TPDELAY Figure 5: propagation delay IN+ IN- RST OUT Figure 6: Turn-on and Turn-off IN+ IN- 9V DESAT RDY FLT 1.0...2.25us RST Tdesatflt Figure 7: Desaturation Fault Datasheet 17 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Timing Diagrams IN+ IN- Vcc1 Vcc2 OUT RDY FLT RST Figure 8: UVLO Datasheet 18 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Package Outlines 7 Package Outlines Figure 9: PG-DSO-20-55 (Plastic Dual Small Outline Package) Datasheet 19 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Application Notes 8 8.1 Application Notes Reference Layout for Thermal Data The PCB layout shown in figure 12 represents the reference layout used for the thermal characterisation. Pins 11, 12, 19 and 20 (GND1) and pins 1, 2, 9 and 10 (VEE2) require ground plane connections for achiving maximum power dissipation. The 1ED020I12FA is conceived to dissipate most of the heat generated through this pins. PCB + Top-Layer PCB + Bottom-Layer Figure 10: Reference layout for thermal data (Copper thickness 102µm) 8.2 Printed Circuit Board Guidelines Following factors should be taken into account for an optimum PCB layout. - Sufficient spacing should be kept between high voltage isolated side and low voltage side circuits. - The same minimum distance between two adjacent high-side isolated parts of the PCB should be maintained to increase the effective isolation and reduce parasitic coupling. - In order to ensure low supply ripple and clean switching signals, bypass capacitor trace lengths should be kept as short as possible. Datasheet 20 Version 2.1, 2009-11-24 EICEDRIVER® 1ED020I12FA Application Notes Datasheet 21 Version 2.1, 2009-11-24 Total Quality Management Qualität hat für uns eine umfassende Bedeutung. Wir wollen allen Ihren Ansprüchen in der bestmöglichen Weise gerecht werden. Es geht uns also nicht nur um die Produktqualität – unsere Anstrengungen gelten gleichermaßen der Lieferqualität und Logistik, dem Service und Support sowie allen sonstigen Beratungs- und Betreuungsleistungen. Dazu gehört eine bestimmte Geisteshaltung unserer Mitarbeiter. Total Quality im Denken und Handeln gegenüber Kollegen, Lieferanten und Ihnen, unserem Kunden. Unsere Leitlinie ist jede Aufgabe mit „Null Fehlern“ zu lösen – in offener Sichtweise auch über den eigenen Arbeitsplatz hinaus – und uns ständig zu verbessern. Unternehmensweit orientieren wir uns dabei auch an „top“ (Time Optimized Processes), um Ihnen durch größere Schnelligkeit den entscheidenden Wettbewerbsvorsprung zu verschaffen. Geben Sie uns die Chance, hohe Leistung durch umfassende Qualität zu beweisen. Wir werden Sie überzeugen. Quality takes on an allencompassing significance at Semiconductor Group. For us it means living up to each and every one of your demands in the best possible way. So we are not only concerned with product quality. We direct our efforts equally at quality of supply and logistics, service and support, as well as all the other ways in which we advise and attend to you. Part of this is the very special attitude of our staff. Total Quality in thought and deed, towards co-workers, suppliers and you, our customer. Our guideline is “do everything with zero defects”, in an open manner that is demonstrated beyond your immediate workplace, and to constantly improve. Throughout the corporation we also think in terms of Time Optimized Processes (top), greater speed on our part to give you that decisive competitive edge. Give us the chance to prove the best of performance through the best of quality – you will be convinced. www.infineon.com/gatedriver Published by Infineon Technologies AG