BAS3007A

BAS3007A... Low VF Schottky Diode Array • Reverse voltage: 30 V • Forward current: 0.9 A • Small diode quad array for polarity independence, reverse polarity protection and low loss bridge rectification • Very low forward voltage: 0.5 V typ. @ 0.7 A (per diode) • Fast switching • Pb-free (ROHS compliant) package 1) • Qualified according AEC Q101 BAS3007A-RPP + D4 4 D3 3 ~ D2 - D1 1 2 ~ Type BAS3007A-RPP Parameter Diode reverse voltage2) Peak reverse voltage2) RMS reverse voltage2) Forward current 2) TS ≤ 46°C TS ≤ 82°C Package SOT143 Configuration bridge Symbol VR VRM VR(RMS) IF 900 700 I FSM Tj T stg 5 150 -65 ... 150 Value 30 30 21 Marking E1s Unit V Maximum Ratings at TA = 25°C, unless otherwise specified mA Non-repetitive peak surge forward current (t ≤ 10 ms) Junction temperature Storage temperature 1Pb-containing 2For A °C package may be available upon special request TA > 25°C the derating of VR and IF has to be considered. Please refer to the attached curves. 1 2007-11-20 BAS3007A... Thermal Resistance Parameter Junction - soldering point 1) Symbol RthJS Value ≤ 95 Unit K/W Unit Electrical Characteristics at TA = 25°C, unless otherwise specified Parameter Symbol Values min. typ. max. DC Characteristics Reverse current (per diode)2) IR VR = 12 V VR = 30 V Forward voltage (per diode)2)3) IF = 100 mA IF = 350 mA IF = 500 mA IF = 700 mA IF = 900 mA VF 0.35 0.4 0.45 0.5 0.6 0.4 0.5 0.55 0.6 0.7 30 350 µA V AC Characteristics Diode capacitance (per diode) VR = 5 V, f = 1 MHz 1For CT - 9 15 pF calculation of RthJA please refer to Application Note Thermal Resistance test, tp = 300 µs; D = 0.01 2Pulsed 3When used as shown for Reverse Polarity Protection (RPP, see page 4), the voltage available to the circuit being protected will be two diode drops below the power supply voltage. In other words, the supply current will pass through two diodes. 2 2007-11-20 BAS3007A... Diode capacitance CT = ƒ (VR) f = 1MHz (per diode) 30 pF 26 24 22 Forward Voltage VF = ƒ (TA) IF = Parameter (per diode) 0.7 V 0.6 0.55 0.5 IF = 900mA IF = 700mA CT 20 18 16 14 12 10 8 6 4 0 5 10 15 20 V VF 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 IF = 350mA IF = 100mA 30 0 -45 -15 15 45 75 °C 135 VR TA Forward current IF = ƒ (VF) TA = Parameter (per diode) 10 0 Permissible Reverse voltage VR = ƒ (TA) tp = Paramter, Duty cycle < 0.01 Device mounted on PCB with Rth = 160 K/W 35 V +125°C +85°C +25°C -40°C A VRmax 25 IF 20 DC 20 ms 1 ms 15 10 5 10 -1 0.15 0.25 0.35 0.45 V 0.65 0 0 20 40 60 80 100 °C 130 VF TA 3 2007-11-20 BAS3007A... Forward current IF = ƒ (T S) Current flows through two chips per package at the same time (per array) 1000 mA 800 700 IF 600 500 400 300 200 100 0 0 90 105 120 °C 15 30 45 60 75 150 TS Application example BAS3007A-RPP Advanced Reverse Polarity Protection(RPP): due to diode orientation, circuit at the right will be protected from damage and will also function normally in the event reverse polarity is applied to pins 2 and 3 of the BAS3007A-RPP. Ground 2 1 Reverse polarity protected circuit 3 4 +Vs Ground / +Vs DC Plug to power supply +Vs / Ground 4 2007-11-20 Package SOT143 BAS3007A... Package Outline 0.15 MIN. 2.9 ±0.1 1.9 4 3 B 1 ±0.1 0.1 MAX. 1.3 ±0.1 2.4 ±0.15 10˚ MAX. 1 2 10˚ MAX. 0.2 0.8 +0.1 -0.05 0.4 +0.1 -0.05 1.7 0.25 M B 0.08...0.1 A 5 0...8˚ 0.2 M A Foot Print 0.8 1.2 0.8 0.9 1.2 0.8 0.8 Marking Layout (Example) Manufacturer RF s Pin 1 56 Standard Packing Reel ø180 mm = 3.000 Pieces/Reel Reel ø330 mm = 10.000 Pieces/Reel 0.9 1.1 2005, June Date code (YM) BFP181 Type code 4 0.2 Pin 1 3.15 2.6 8 1.15 5 2007-11-20 BAS3007A... Edition 2006-02-01 Published by Infineon Technologies AG 81726 München, Germany © Infineon Technologies AG 2007. All Rights Reserved. Attention please! The information given in this dokument shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 6 2007-11-20