BAT15-099

BAT15... Silicon Schottky Diodes • Low barrier type for DBS mixer applications up to 12 GHz, phase detectors and modulators • Low noise figure • Pb-free (RoHS compliant) package 1) • Qualified according AEC Q101 BAT15-02LRH BAT15-03W BAT15-04W ! BAT15-05W ! BAT15-099 BAT15-099LRH " ! BAT15-099R " !  , , , , , , , ,! ," ,     ESD (Electrostatic discharge) sensitive device, observe handling precaution! Type BAT15-02LRH BAT15-03W BAT15-04W BAT15-05W BAT15-07LRH BAT15-098LRH BAT15-099 BAT15-099R BAT15-099LRH 1Pb-containing Package TSLP-2-7 SOD323 SOT323 SOT323 TSLP-4-7 TSLP-4-7 SOT143 SOT143 TSLP-4-7 Configuration single, leadless single series common cathode parallel pair, leadless anti-parallel pair, leadless anti-parallel pair cross-over ring anti-parallel pair, leadless LS(nH) 0.4 1.8 1.4 1.4 0.4 0.4 2 2 0.4 Marking NP white P S8s S5s NP B S5s S6s S5 package may be available upon special request 1 2010-03-05 BAT15... Maximum Ratings at TA = 25°C, unless otherwise specified Parameter Diode reverse voltage Forward current Total power dissipation BAT15-02LRH, -099LRH TS ≤ 76 °C BAT15-03W, TS ≤ 70 °C BAT15-04W, TS ≤ 68 °C BAT15-05W, TS ≤ 65 °C BAT15-099, TS ≤ 48 °C BAT15-099R, TS ≤ 67 °C Junction temperature Operating temperature range Storage temperature Thermal Resistance Parameter Junction - soldering point 1) BAT15-02LRH, -099LRH BAT15-03W BAT15-04W BAT15-05W BAT15-099 BAT15-099R 1For Symbol VR IF Ptot Value 4 110 100 100 100 100 100 100 150 -55 ... 150 -55 ... 150 Unit V mA mW Tj T op T stg Symbol RthJS °C Value ≤ 780 ≤ 795 ≤ 820 ≤ 850 ≤ 1020 ≤ 830 Unit K/W calculation of RthJA please refer to Application Note Thermal Resistance 2 2010-03-05 BAT15... Electrical Characteristics at TA = 25°C, unless otherwise specified Parameter DC Characteristics Breakdown voltage I(BR) = 100 µA Forward voltage IF = 1 mA IF = 10 mA Forward voltage matching1) IF = 10 mA AC Characteristics Diode capacitance VR = 0 V, f = 1 MHz, all other types VR = 0 V, f = 1 MHz, BAT15-099R Differential forward resistance I F = 10 mA / 50 mA 1∆V Symbol min. V(BR) VF 0.16 0.25 ∆ VF 4 Values typ. max. - Unit V 0.23 0.32 - 0.32 0.41 20 mV CT RF 5.5 0.35 0.5 - pF Ω F is the difference between lowest and highest V F in a multiple diode component. 3 2010-03-05 BAT15... Diode capacitance CT = ƒ (VR) f = 1MHz EHD07082 Reverse current IR = ƒ(VR) TA = Parameter EHD07081 0.5 CT pF 0.4 10 3 ΙR µA 10 2 T A =125 C 85 C 0.3 10 1 25 C 0.2 0 10 0.1 0.0 10 -1 0 2 V VR 4 0 1 2 3 V VR 4 Forward current IF = ƒ (VF) TA = Parameter 10 2 BAT 15-099R EHD07077 Forward current IF = ƒ (T S) BAT15-02LRH, BAT15-099LRH 120 mA ΙF mA 100 10 1 TA = -40 ˚C 25 ˚C 85 ˚C 125 ˚C 10 0 90 80 IF 70 60 50 40 10 -1 30 20 10 10 -2 0.0 0.5 V 1.0 VF 0 0 15 30 45 60 75 90 105 120 °C 150 TS 4 2010-03-05 BAT15... Forward current IF = ƒ (T S) BAT15-03W 120 mA Forward current IF = ƒ (T S) BAT15-04W 120 mA 100 90 80 100 90 80 IF 70 60 50 40 30 20 10 0 0 15 30 45 60 75 90 105 120 °C 150 IF 70 60 50 40 30 20 10 0 0 15 30 45 60 75 90 105 120 °C 150 TS TS Forward current IF = ƒ (T S) BAT15-05W 120 mA Forward current IF = ƒ (T S) BAT15-099 120 mA 100 90 80 100 90 80 IF 70 60 50 40 30 20 10 0 0 15 30 45 60 75 90 105 120 °C 150 IF 70 60 50 40 30 20 10 0 0 15 30 45 60 75 90 105 120 °C 150 TS TS 5 2010-03-05 BAT15... Forward current IF = ƒ (T S) BAT15-099R 120 mA 100 90 80 IF 70 60 50 40 30 20 10 0 0 15 30 45 60 75 90 105 120 °C 150 TS Permissible Puls Load RthJS = ƒ (tp) BAT15-02LRH, BAT15-099LRH 10 3 Permissible Pulse Load IFmax / I FDC = ƒ (t p) BAT15-02LRH, BAT15-099LRH 10 1 10 2 0.5 0.2 0.1 0.05 0.02 0.01 0.005 D=0 IFmax/IFDC K/W RthJS D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 1 -7 10 10 -6 10 -5 10 -4 10 -3 10 -2 s 10 0 10 0 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 tp tp 6 2010-03-05 BAT15... Permissible Puls Load RthJS = ƒ (tp) BAT15-03W 10 3 Permissible Pulse Load IFmax / I FDC = ƒ (t p) BAT15-03W 10 1 10 2 D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 I Fmax/IFDC K/W RthJS D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 1 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 10 0 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 tp tp Permissible Puls Load RthJS = ƒ (tp) BAT15-04W 10 3 Permissible Pulse Load IFmax / I FDC = ƒ (t p) BAT15-04W 10 1 10 2 D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 IFmax/IFDC K/W RthJS D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 1 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 10 0 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 tp tp 7 2010-03-05 BAT15... Permissible Puls Load RthJS = ƒ (tp) BAT15-05W 10 3 Permissible Pulse Load IFmax / I FDC = ƒ (t p) BAT15-05W 10 1 10 2 D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 I Fmax/IFDC K/W RthJS D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 1 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 10 0 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 tp tp Permissible Puls Load RthJS = ƒ (tp) BAT15-099 10 3 Permissible Pulse Load IFmax / I FDC = ƒ (t p) BAT15-099 10 1 IFmax/IFDC K/W RthJS 10 2 D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 1 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 10 0 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 tp tp 8 2010-03-05 BAT15... Permissible Puls Load RthJS = ƒ (tp) BAT15-099R 10 3 Permissible Pulse Load IFmax / I FDC = ƒ (t p) BAT15-099R 10 1 I Fmax/IFDC K/W RthJS 10 2 D=0.5 0.2 0.1 0.05 0.02 0.01 0.005 0 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 1 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 10 0 -6 10 10 -5 10 -4 10 -3 10 -2 s 10 0 tp tp 9 2010-03-05 BAT15... S11-Parameters for BAT15-099 Typical impedance characteristics (with external bias I and Zo = 50Ω) f I = 0.02 mA ANG I = 0.05 mA MAG ANG I = 0.1 mA MAG ANG I = 0.2 mA MAG ANG I = 0.5 mA MAG ANG GHz MAG 1 2 3 4 5 6 7 8 9 10 11 12 0.94 0.93 0.92 0.91 0.91 0.91 0.91 0.91 0.91 0.9 0.89 0.88 -16.4 -33.8 -53.8 -74.3 -96.6 -115.4 -131 -143 -155.6 -167.3 175.5 175.5 0.84 0.88 0.86 0.84 0.84 0.84 0.84 0.84 0.83 0.83 0.8 0.76 -16.6 -33.8 -54.5 -75.3 -97.6 -116.7 -132.3 -144.5 -150.2 -169.7 172.6 146.5 0.77 0.77 0.75 0.72 0.72 0.73 0.73 0.73 0.71 0.71 0.7 0.62 -16.4 -34.5 -54.1 -76.4 -99.1 -118.7 -134.1 -146.8 -159.7 -178.8 170 142.8 0.59 0.58 0.58 0.51 0.53 0.53 0.54 0.55 0.53 0.51 0.45 0.39 -17.2 -35.2 -56.1 -78.4 -102.3 -122.9 -138.1 -150.5 -163.9 -175.8 164.9 134.2 0.19 0.15 0.13 0.11 0.15 0.18 0.2 0.81 0.18 0.14 0.09 0.14 -16.7 -36.1 -64.8 -104.8 -135.7 -160.9 -168.8 179.4 179.4 151.2 105.5 43.6 S11 = (f, I) BAT15-099 + j 50 + j 25 0.02 mA 12 Hz 0.05 mA + j 10 f 10 25 + j 100 0.1 mA 0.2 mA 0.5 mA + j 250 0 50 100 250 Ω 1 GHz - j 250 - j10 8 GHz - j 25 5 GHz - j50 - j 100 EHD07083 10 2010-03-05 Package SOD323 BAT15... 11 2010-03-05 Package SOT143 BAT15... Package Outline 0.15 MIN. 2.9 ±0.1 1.9 4 3 B 1 ±0.1 0.1 MAX. 1.3 ±0.1 2.4 ±0.15 10˚ MAX. 1 2 10˚ MAX. 0.2 0.8 +0.1 -0.05 0.4 +0.1 -0.05 1.7 0.25 M B 0.08...0.1 A 5 0...8˚ 0.2 M A Foot Print 0.8 1.2 0.8 0.9 1.2 0.8 0.8 Marking Layout (Example) Manufacturer RF s Pin 1 56 Standard Packing Reel ø180 mm = 3.000 Pieces/Reel Reel ø330 mm = 10.000 Pieces/Reel 0.9 1.1 2005, June Date code (YM) BFP181 Type code 4 0.2 Pin 1 3.15 2.6 8 1.15 12 2010-03-05 Package SOT323 BAT15... Package Outline 2 ±0.2 0.3 +0.1 -0.05 3 1.25 ±0.1 2.1 ±0.1 0.9 ±0.1 3x 0.1 M 0.1 MAX. 0.1 A 1 0.65 0.65 2 0.1 MIN. 0.15 +0.1 -0.05 0.2 M A Foot Print 0.6 0.8 0.65 0.65 Marking Layout (Example) Manufacturer 1.6 2005, June Date code (YM) Pin 1 BCR108W Type code Standard Packing Reel ø180 mm = 3.000 Pieces/Reel Reel ø330 mm = 10.000 Pieces/Reel 4 0.2 Pin 1 2.15 2.3 8 1.1 13 2010-03-05 Package TSLP-2-7 BAT15... Package Outline Top view 0.39 +0.01 -0.03 0.05 MAX. 0.65 ±0.05 Bottom view 0.6 ±0.05 2 2 1 1 Cathode marking 0.5 ±0.035 1) 1) Dimension applies to plated terminal Foot Print For board assembly information please refer to Infineon website "Packages" 0.35 0.45 0.3 0.925 1 0.275 0.275 0.375 0.6 Copper Solder mask 0.35 Stencil apertures Marking Layout (Example) BAR90-02LRH Type code Cathode marking Laser marking Standard Packing Reel ø180 mm = 15.000 Pieces/Reel Reel ø330 mm = 50.000 Pieces/Reel (optional) 4 1.16 0.5 Cathode marking 0.76 8 0.25 ±0.035 1) 1±0.05 14 2010-03-05 Package TSLP-4-7 BAT15... Package Outline Top view 0.39 +0.01 -0.03 0.05 MAX. 4 x 0.25 ±0.035 1) 2 3 Bottom view 4 x 0.35 ±0.035 4 1) 0.8 ±0.05 4 1 2 1 Pin 1 marking 1) Dimension applies to plated terminal 0.45 ±0.05 Foot Print For board assembly information please refer to Infineon website "Packages" 0.8 0.4 0.78 0.38 1.18 0.28 0.3 0.3 0.2 Copper Solder mask 0.22 Stencil apertures 0.28 Marking Layout (Example) BAR90-07LRH Type code Pin 1 marking Laser marking Standard Packing Reel ø180 mm = 15.000 Pieces/Reel 4 1.45 8 0.5 Pin 1 marking 1.05 0.38 0.4 0.42 1.2 0.4 1.2 ±0.05 3 0.75 ±0.05 15 2010-03-05 BAT15... Edition 2009-11-16 Published by Infineon Technologies AG 81726 Munich, Germany  2009 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 16 2010-03-05