ESD5V3S1B-02LRH

ESD5V3S1B-02LRH Silicon TVS Diode • ESD / transient protection of data and power lines in low voltage applications according to: IEC61000-4-2 (ESD): ± 25 kV (air) 20 kV (contact) IEC61000-4-4 (EFT): 50 A / 2.5 kV (5/50 ns) IEC61000-4-5 (surge): 5.5 A / 80 W (8/20 µs) • Small form factor (0402 inch): 1.0 x 0.6 x 0.4 mm 3 • Bi-directional, symmetrical working voltage up to ± 5.3 V • Ultralow and symmetric clamping voltage • Ultralow dynamic resistance 0.4 Ω • Very fast response time • Pb-free (RoHS compliant) package • Qualified according AEC Q101 Applications Recommended to protect audio lines / microphone lines / speaker and headset systems in: • Mobile phones • Mobile TV • Set top boxes • MP3 players • Minidisc players • Portable entertainment electronics ESD5V3S1B-02LRH 1 2 Type ESD5V3S1B-02LRH Package TSLP-2-17 Configuration 1 line, bi-directional 1 Marking E1 2009-12-07 ESD5V3S1B-02LRH Maximum Ratings at TA = 25°C, unless otherwise specified Parameter ESD air / contact discharge 1) Peak pulse current ( tp = 8 / 20 µs)2) Peak pulse power (tp = 8 / 20 µs2) Operating temperature range Storage temperature Symbol VESD I pp P pk T op T stg Value 25 / 20 5.5 80 -55...125 -65...150 Unit kV A W °C Electrical Characteristics at TA = 25°C, unless otherwise specified Parameter Characteristics Reverse working voltage Breakdown voltage I(BR) = 1 mA Reverse current VR = 3.3 V Clamping voltage IPP = 1 A, tp = 8/20 µs2) IPP = 3.5 A, tp = 8/20 µs2) IPP = 5.5 A, tp = 8/20 µs2) Diode capacitance VR = 0 V, f = 1 MHz VR = 2.5 V, f = 1 MHz Dynamic resistance3) (tp = 30 ns) 1V 2I 3 Symbol min. VRWM V(BR) IR VCL CT RD -5.3 6 - Values typ. max. 5.3 0.1 Unit V µA V 8 10 11 17.5 14.5 0.4 10 12 13 pF 20 Ω ESD according to IEC61000-4-2 pp according to IEC61000-4-5 according to TLP tests 2 2009-12-07 ESD5V3S1B-02LRH Power derating curve Ppk = ƒ (TA) Clamping voltage, V cl = ƒ(Ipp) tp = 8 / 20 µs 14 V 110 % 90 Ppk or Ipp 80 12 V cl °C 70 60 11 10 50 40 30 20 10 0 0 25 50 75 100 150 7 9 8 6 0 1 2 3 4 A 6 TA I pp Reverse current IR = ƒ (TA) VR = 3.3 V 10 -6 Breakdown voltage V BR = ƒ(T A) IR = 1 mA 8 V A 7.5 VBR 100 °C 10 -7 IR 7.25 7 10 -8 6.75 6.5 6.25 10 -9 -75 -50 -25 0 25 50 75 150 6 -75 -50 -25 0 25 50 75 100 °C 150 TA TA 3 2009-12-07 ESD5V3S1B-02LRH Diode capacitance CT = ƒ (VR) f = 1MHz 20 pF 16 14 CT 12 10 8 6 4 2 0 0 V 1 2 3 4 6 VR 4 2009-12-07 ESD5V3S1B-02LRH Application example single channel, bi-directional Connector Protected signal line I/O ESD sensitive device 2 The protection diode should be placed very close to the location where the ESD or other transients can occur to keep loops and inductances as small as possible. Pin 1 (or pin 2) should be connected directly to a ground plane on the board . 1 5 2009-12-07 TSLP-2-17 (mm) ESD5V3S1B-02LRH Package Outline Top view 0.39 +0.01 -0.03 0.05 MAX. 0.65 ±0.05 Bottom view 0.6 ±0.05 2 2 1 1 Cathode marking 0.5 ±0.035 1) 1) Dimension applies to plated terminal Foot Print For board assembly information please refer to Infineon website "Packages" 0.35 0.45 0.3 0.925 1 0.275 0.275 0.375 0.6 Copper Solder mask 0.35 Stencil apertures Marking Layout (Example) BAR90-02LRH Type code Cathode marking Laser marking Standard Packing Reel ø180 mm = 15.000 Pieces/Reel Reel ø330 mm = 50.000 Pieces/Reel (optional) 4 1.16 0.5 Cathode marking 0.76 8 0.25 ±0.035 1) 1±0.05 6 2009-12-07 ESD5V3S1B-02LRH Edition 2009-11-16 Published by Infineon Technologies AG 81726 Munich, Germany  2009 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office ( ). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. 7 2009-12-07