KP236

BAP Analog Barometric Air Pressure Sensor IC KP 2 3 6 Analog Absolute Pressure Sensor   Da t a S h e e t Revision 1.0, 2010-06-21 S e n s e & Co n tr o l Edition 2010-06-21 Published by Infineon Technologies AG 81726 Munich, Germany © 2010 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. KP236 Analog Absolute Pressure Sensor Data Sheet 3 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor KP236 Analog Absolute Pressure Sensor Revision History: 2010-06-21, Revision 1.0 Previous Revision: Revision 0.9 Page Page 17 Page 18 Subjects (major changes since last revision) Comment about application circuit example added Thermal resistance specified according JESD51-2 Change document status from preliminary to final Trademarks of Infineon Technologies AG A-GOLD™, BlueMoon™, COMNEON™, CONVERGATE™, COSIC™, C166™, CROSSAVE™, CanPAK™, CIPOS™, CoolMOS™, CoolSET™, CONVERPATH™, CORECONTROL™, DAVE™, DUALFALC™, DUSLIC™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, E-GOLD™, EiceDRIVER™, EUPEC™, ELIC™, EPIC™, FALC™, FCOS™, FLEXISLIC™, GEMINAX™, GOLDMOS™, HITFET™, HybridPACK™, INCA™, ISAC™, ISOFACE™, IsoPACK™, IWORX™, M-GOLD™, MIPAQ™, ModSTACK™, MUSLIC™, my-d™, NovalithIC™, OCTALFALC™, OCTAT™, OmniTune™, OmniVia™, OptiMOS™, OPTIVERSE™, ORIGA™, PROFET™, PRO-SIL™, PrimePACK™, QUADFALC™, RASIC™, ReverSave™, SatRIC™, SCEPTRE™, SCOUT™, S-GOLD™, SensoNor™, SEROCCO™, SICOFI™, SIEGET™, SINDRION™, SLIC™, SMARTi™, SmartLEWIS™, SMINT™, SOCRATES™, TEMPFET™, thinQ!™, TrueNTRY™, TriCore™, TRENCHSTOP™, VINAX™, VINETIC™, VIONTIC™, WildPass™, X-GOLD™, XMM™, X-PMU™, XPOSYS™, XWAY™. Other Trademarks AMBA™, ARM™, MULTI-ICE™, PRIMECELL™, REALVIEW™, THUMB™ of ARM Limited, UK. AUTOSAR™ is licensed by AUTOSAR development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG. FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay Consortium. HYPERTERMINAL™ of Hilgraeve Incorporated. IEC™ of Commission Electrotechnique Internationale. IrDA™ of Infrared Data Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics Corporation. Mifare™ of NXP. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™ of MURATA MANUFACTURING CO. OmniVision™ of OmniVision Technologies, Inc. Openwave™ Openwave Systems Inc. RED HAT™ Red Hat, Inc. RFMD™ RF Micro Devices, Inc. SIRIUS™ of Sirius Sattelite Radio Inc. SOLARIS™ of Sun Microsystems, Inc. SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™ of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex Limited. Last Trademarks Update 2009-10-19 Data Sheet 4 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Table of Contents Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1 1.1 1.2 2 2.1 2.2 2.3 2.4 2.5 2.5.1 2.5.2 2.6 2.7 3 3.1 3.2 3.3 3.4 4 4.1 4.2 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Target Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Ratiometric Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Overall Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Output Voltage versus Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Timing Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application Circuit Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 17 18 19 20 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 PG-DSOF-8-16 Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Identification Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Data Sheet 5 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor List of Figures List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Pin configuration (top view, figure not to scale) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transfer function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ratiometric error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accuracy for pressure acquisition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum output voltage limit with pull-down load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minimum output voltage limit with pull-up load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-up time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Response and stabilization time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application circuit example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package outline (all dimensions in mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 11 12 13 14 15 15 16 16 17 22 23 Data Sheet 6 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor List of Tables List of Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transfer function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ratiometric Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Component Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 12 13 14 17 18 19 20 21 Data Sheet 7 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Product Description KP236 1 Product Description The KP236 is a miniaturized Analog Barometric Air Pressure Sensor IC based on a capacitive principle. It is surface micromachined with a monolithic integrated signal conditioning circuit implemented in BiCMOS technology. The sensor converts a pressure into an analog output signal. The calibrated transfer function converts a pressure range of 40 kPa to 115 kPa into a voltage range of 0.5 V to 4.5 V. The chip is packaged in a “green” SMD housing. The sensor has been primarily developed for measuring barometric air pressure, but can also be used in other application fields. The high accuracy and the high sensitivity of the device makes it a perfect fit for advanced automotive applications as well as in industrial and consumer applications. 1.1 • • • • • • Features Following features are supported by the KP236: High precision pressure sensing (± 1.0 kPa) Ratiometric analog output Large temperature range (-40 ° to 125 ° C C) Broken wire detection “Green” 8 pin SMD housing Automotive qualified 1.2 • • • • • • Target Applications The KP236 is defined for use in following target applications: Automotive applications (barometric air pressure measurement) Industrial control Consumer applications Medical applications Weather stations Altimeters Product Name Analog Absolute Pressure Sensor Data Sheet Product Type KP236 8 Ordering Code SP000700780 Package PG-DSOF-8-16 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Functional Description 2 Functional Description The pressure is detected by an array of capacitive surface micromachined sensor cells. The sensor cell output is amplified, temperature compensated and linearized to obtain an output voltage that is proportional to the applied pressure. The transfer function for linearization is computed in the digital part of the sensor using a third order polynomial calculation. The transfer function is created from the following parameters: • • Minimum and maximum rated pressure Voltage level at minimum and maximum rated pressure The output is analog and ratiometric with respect to the supply voltage. All parameters needed for the complete calibration algorithm — such as offset, gain, temperature coefficients of offset and gain, and linearization parameters — are determined after assembly. The parameters are stored in an integrated E²PROM. The E²PROM content is protected with forward error correction (a one bit error is detected and corrected, errors of more than one bit are detected and the output signal is switched to ground potential). Open Bond Detection When the chip is not powered properly, the JFET transistors of the broken wire detection stage are selfconducting. For example, if the GND connection is interrupted, the output is drawn strongly to VDD. Similarly, if the VDD connection is broken, the output is drawn to GND. Data Sheet 9 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Functional Description 2.1 Pin Configuration Figure 1 shows the pin configuration. TEST CLOCK / VPROG DATA IN DATA OUT 1 2 3 4 8 7 6 5 GND VOUT GND VDD Figure 1 Pin configuration (top view, figure not to scale) 2.2 Pin Description Table 1 shows the pin description. Table 1 Pin No. 1 2 3 4 5 6 7 8 Pin Description Name TEST CLOCK / VPROG DATA IN DATA OUT VDD GND VOUT GND Function Test pin1) External clock for communication / programming voltage1) Serial data input pin1) Serial data output pin1) Supply voltage Circuit ground potential2) Analog pressure signal output Circuit ground potential2) 1) Digital pins are used only during calibration and test. It is recommended to leave these pins floating (in case of an open GND connection, the floating pins prevent from a cross grounding through the corresponding ESD diodes). 2) It is recommended to connect both GND pins. Data Sheet 10 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Functional Description 2.3 Block Diagram Figure 2 shows the functional block diagram. VDD CLOCK / VPROG DATA IN DATA OUT Internal Reference Voltage EEPROM ( 90+22 bit ) Test and Programming Interface Digital Control Temperature Compensation VOUT A D 1 bit 1 kHz 12 bit Linearization 10 bit D A 30kHz VDD Clock Generator OBD GND Figure 2 Functional block diagram Data Sheet 11 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Functional Description 2.4 Transfer Function The KP236 device is fully calibrated on delivery. The sensor has a linear transfer function between the applied pressure and the output signal: V OUT = VDD x (a x P + b) The output signal is ratiometric. Gain a and offset b are determined during calibration in order to generate the required transfer function. Calibrated Transfer Function The following calibration is adjusted with the parameters a and b: Table 2 Symbol pIN,1 pIN,2 Transfer function Pressure Values 40 115 Unit kPa kPa Output Voltage @ VDD = VDD,Typ Symbol VOUT,1 VOUT,2 Values 0.5 4.5 Unit V V a b Gain and Offset Symbol Value 0.01067 -0.32667 Unit 1/kPa – Note: The points pIN,1/VOUT,1 and pIN,2/VOUT,2 define the calibrated transfer function and not the operating range. The operating pressure range is defined by the parameter 2.4 “Ambient operating pressure range” on Page 19 VOUT [V] 5.0 4.0 3.0 2.0 1.0 0.0 10 30 50 70 90 110 130 150 pressure [kPa] operating pressure range maximum input pressure range Figure 3 Transfer function Note: The application circuitry determines the current driven by the device and thus may have an impact on the output voltage delivered by the sensor. Data Sheet 12 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Functional Description 2.5 Accuracy The accuracy of the KP236 sensor is influenced by the supply voltage (ratiometric error) as well as by pressure, temperature and aging effects. The specified value, calculated with the transfer function, represents the theoretical value (see Figure 3). The error equals the deviation between the measured output voltage value and the specified output voltage value. 2.5.1 Ratiometric Error Ideally the sensor is ratiometric - the output (VOUT) scales by the same ratio that VDD increases or decreases. The ratiometric error is defined as the difference between the ratio that VDD changed and the ratio that VOUT changed, expressed as a percentage. VOUT(@VDD) - V OUT(@5V) x ERAT (%) = 5V VDD 5V x 100% The output voltage VOUT is ratiometric to VDD. VDD must be in the operating range provided in Table 7. Table 3 Ratiometric Error Max. ratiometric error (ERAT in % of VDD, Typ) ± 0.5 0 ± 0.5 Supply voltage (V) VDD,Min VDD,Typ VDD,Max E RAT (%) 0.5 0 -0.5 VDD,MIN VDD,TYP VDD,MAX VDD Figure 4 Ratiometric error 2.5.2 Overall Accuracy Overall accuracy covers the entire pressure and temperature range from different sources of error including the following: • • • Pressure: Temperature: Aging: Output deviation from target transfer function over the specified pressure range Output deviation over the temperature range Parameter drift over life time Data Sheet 13 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Functional Description Note: Ratiometric signal error is not included in the overall accuracy. For error measurements, the supply voltage must have the nominal value (VDD = VDD,Typ). The error band is determined by three continuous lines through four relevant breakpoints. Table 4 -40 0 85 125 Accuracy Error [kPa] ±2.0 ±1.0 ±1.0 ±2.0 Temperature [°C] Error Multiplier 2.0 1.0 1.0 2.0 2.0 2.0 1.5 1.0 1.0 0.5 0.0 -40 0 85 temperature [° C] 125 Figure 5 Accuracy for pressure acquisition Data Sheet 14 Revision 1.0, 2010-06-21 absolute error [kPa] error multiplier 2.5 KP236 Analog Absolute Pressure Sensor Functional Description 2.6 • • Output Voltage versus Load The output voltage limits depend on: The value of the external load resistor. The type of connection (pull-up or pull-down). pull-down resistance [kΩ] 5 VOUT [V] 5.00 4.90 4.85 50 20 10 4.80 4.70 4.60 4.50 0.0 0.1 0.2 0.4 0.6 0.8 1.0 source current [mA] Figure 6 Maximum output voltage limit with pull-down load pull-up resistance [k Ω] 50 VOUT [V] 0.50 0.40 0.30 0.20 0.10 0 0.0 0.1 0.2 0.4 0.6 0.8 1.0 source current [mA] 20 10 5 Figure 7 Minimum output voltage limit with pull-up load Note: The values in the diagrams are valid for the entire specified temperature range. The two diagrams above do not take into account clamping levels. In case clamping levels are implemented, the output voltage is clamped accordingly. Data Sheet 15 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Functional Description 2.7 Timing Properties Power-up Time The power-up time tUP is defined as the maximum time between the supply voltage reaching its operating range and the output voltage reaching 90% of its final value (assuming pin VOUT open and constant input pressure). voltage [V] 5 4 3 2 1 tUP VDD V OUT 90% of Final Value constant input pressure 0 0 2.5 5 7.5 10 12.5 15 time [ms] Figure 8 Power-up time Response Time and Stabilization Time The response time tR is defined as the time required by the output to change from 10% to 90% of its final value after a specified pressure step (assuming pin VOUT open). The stabilization time tS is defined as the time required by the output to meet the specified accuracy after the pressure has been stabilized (assuming pin VOUT open). voltage [V] 120 5 4 3 2 1 0 0 1 2 3 4 5 tR 10% of final value tS input pressure 100 within required accuracy 90% of final value VOUT 80 60 40 20 0 time [ms] Figure 9 Response and stabilization time Note: The values in the diagrams are valid for the entire specified temperature range. Data Sheet 16 pressure [kPa] Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Specification 3 Specification 3.1 Application Circuit Example It is recommended to protect the pressure sensor IC against overload and electro-magnetic interferences (as shown in Figure 10). The output circuit acts as a low-pass decoupling filter between the sensor IC output and the A/D input of the microcontroller. The shown application circuit example considers an increased cable length between the sensor and the microcontroller. A combined location on a PCB with reduced distance between the sensor and the controller allows a reduction of the numbers of the passive components (e.g. C2, R1 and R2 can be omitted). 5V n.c. n.c. n.c. n.c. 1 2 3 4 Test C LOCK / VPROG DATA IN VDD 5 C1 Ref R1 *) ADC KP 2xx GND 6 C2 A/D in R3 C3 Microcontroller VOUT 7 8 R2 *) GND D ATA OUT GND *) R 1 and R2 o nly alternatively Figure 10 Application circuit example Note: It is recommended to leave the digital pins CLOCK/VPROG, DATA IN and DATA OUT floating (in case of an open GND connection, the floating pins prevent from a cross grounding through the corresponding ESD diodes). Table 5 Component Pull-Up Resistor Pull-Down Resistor Low Pass Resistor Supply Blocking Capacitor Output Blocking Capacitor Low Pass Capacitor Component Values Symbol Min. Values Typ. 59 59 22 100 100 100 Unit Max. 100 100 100 100 100 100 kΩ kΩ kΩ nF nF nF R1 R2 R3 C1 C2 C3 5 5 3.9 10 0 10 Data Sheet 17 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Specification 3.2 Absolute Maximum Ratings Table 6 Parameter Absolute Maximum Ratings Symbol Min. Values Typ. – – – – – – Unit Max. 6.5 16.5 – V V V Note / Test Condition – 1 h @ 70° C Limited time: Max. 300 s – – – Number 1.1 Supply voltage VDD_max -0.3 – -6.51) -0.3 – – Output voltage VOUT VDD + 0.3 V 20 5 V V 1.2 1.3 1.4 Voltage on VCLK CLOCK / VPROG pin Voltage on DATA IN & DATA_OUT pins Storage temperature VDATA TS -60 – – – 150 180 ° C K/W – Thermal resistance between the die and ambient; according to JESD51-2 Limited time: Max. 300 s According to EIA / JESD22-A114-E 1.5 1.6 Thermal resistance RthJA Maximum input pressure ESD robustness (HBM: 1.5 kΩ, 100 pF) pamb_max 40 – 150 600 2 kPa kPa kV 1.7 VESD – – 1.8 1) Reverse polarity; IDD < 300 mA Attention: Stresses above the max. values listed in Table 6 may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. Data Sheet 18 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Specification 3.3 Operating Range The following operating conditions must not be exceeded in order to ensure correct operation of the device. All parameters specified in the following sections refer to these operating conditions, unless noted otherwise. Table 7 Parameter Operating Range Symbol Min. Values Typ. 5.0 – – – – – Unit Max. 5.5 1 – 125 115 – V mA mA ° C kPa years Note / Test Condition Number 2.1 Supply voltage Output current on VOUT pin Operating temperature Ambient operating pressure range Lifetime1) VDD IOUT Ta pamb tlive 4.5 – -1 -40 40 15 VOUT is ratiometric to VDD pull-down resistor used 2.2 pull-up resistor used 2.3 2.4 2.5 1) The life time shall be considered as anticipation with regard to the product that shall not extend the agreed warranty period. Data Sheet 19 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Specification 3.4 Characteristics Table 8 Parameter Electrical Characteristics Symbol Min. Values Typ. – Unit Max. 4.85 V Note / Test Condition See also section “Output Voltage versus Load” on Page 15 Number 3.1 Output voltage range VOUT_R 0.10 Supply current IDD – 8 10 mA During power up a peak 3.2 supply current of max. 22 mA is possible 3.3 Output referred noise Response time2) Stabilization time2) Power-up time2) VNOISE tR tS tUP – – – – – – – – 0.65 – – – 2.5 1.8 1.03) 10 5 1 mVRMS Frequency > 1 kHz1) mVRMS Frequency < 1 kHz ms ms ms ms 10% to 90% of the final 3.4 output value For full accuracy 90% of the final output value 3.5 3.6 3.7 Broken wire: tOBD Diagnosis response time4) OBD transistor on resistance RDSON – – 160 Ω 3.8 1) 200 measurements in sequence, bandwidth limited to 40kHz 2) More details in section “Timing Properties” on Page 16 3) The maximum response time considers a maximal value of 100nF for the output blocking capacitor C2 and a maximum pressure pulse equivalent 4.0V output change 4) In the event of a broken wire (broken VDD line or broken GND line), the output changes to certain voltage levels within the broken wire response time. The OBD ranges are determined by the application circuitry Data Sheet 20 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Specification Table 9 Parameter Sensitivity Transfer Function Symbol Min. Values Typ. 53.3 – – – – Unit Max. – 1.0 2.0 2.0 25 mV /kPa kPa kPa kPa mV Note / Test Condition Number 4.1 S accp – -1.0 -2.0 -2.0 -25 Accuracy pressure (overall)1) Ratriometric error2) 0° up to 85 ° C C @ -40°C @ 125° C 4.2 ERAT 4.3 1) More details in section “Overall Accuracy” on Page 13 2) More details in section “Ratiometric Error” on Page 13 Data Sheet 21 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Package Information 4 Package Information The PG-DSOF-8-16 package is optimized regarding external mechanical stress influences. The package fulfills the solder conditions for lead-free board assembly. Details (soldering profile, application notes, etc.) are available under: www.infineon.com/package. Note: In the application, it is recommended to ensure that the same pressure is applied to the whole package. 4.1 PG-DSOF-8-16 Outline OUTER DIMENSIONS DOES NOT INCLUDE PROTUSION OR INTRUSION OF 0.2 MAX. PER SIDE Figure 11 Data Sheet Package outline (all dimensions in mm) 22 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Package Information 4.2 Identification Code The identification code is provided in a machine readable format. The date and sales code are provided in human readable format. B Y Y WW KP236 Sales Code Date Code Data Matrix Code 8 x 18 Dots Dot Size: 0.15 mm x 0.15 mm B: YY: WW: BE Location Year Week Figure 12 Identification Code The identification code for the KP236 is on the same side of the package as pin 8 (GND). Data Sheet 23 Revision 1.0, 2010-06-21 KP236 Analog Absolute Pressure Sensor Data Sheet 24 Revision 1.0, 2010-06-21 www.infineon.com Published by Infineon Technologies AG