Q67006-A9339

Low Drop Voltage Regulator TLE 4296 Features • • • • • • • • • • • • Three versions: 3.0 V, 3.3 V, 5.0 V Output voltage tolerance ≤ ±4% Very low drop voltage Output current: 30 mA Inhibit input Low quiescent current consumption Wide operation range: up to 45 V Wide temperature range: -40 °C ≤ Tj ≤ 150 °C Output protected against short circuit Overtemperature protection Reverse polarity proof Very small SMD-Package P-SCT595-5 SCT 595 Functional Description The TLE 4296 G is a monolithic integrated low drop voltage regulator in the very small SMD package P-SCT595-5. It is designed to supply e.g. microprocessor systems under the severe conditions of automotive applications. Therefore the device is equipped with additional protection functions against overload, short circuit and reverse polarity. At overtemperature the regulator is automatically turned off by the integrated thermal protection circuit. Input voltages up to 40 V are regulated to VQ,nom = 3.0 V (V30 version) 3.3 V (V33 version) or 5.0 V (V50 version). The output is able to drive a load of more than 30 mA while it regulates the output voltage within a 4% accuracy. To save energy the device can be switched in stand-by mode via an inhibit input which causes the current consumption to drop below 5 µA. Type TLE 4296 GV30 TLE 4296 GV33 TLE 4296 GV50 Data Sheet Ordering Code Q67006-A9339 Q67006-A9340 Q67006-A9372 1 Package P-SCT595-5 P-SCT595-5 P-SCT595-5 Rev. 1.0, 2004-01-01 TLE 4296 INH 1 5 GND GND 2 Ι 3 4 Q AEP02253 Figure 1 Table 1 Pin No. 1 2 3 4 5 Pin Configuration (top view) Pin Definitions and Functions Symbol INH GND I Q GND Function Inhibit input; high level to turn IC on Ground; connected to pin 5 Input voltage Output voltage; must be blocked by a capacitor CQ ≥ 2.2 µF, 3 Ω ≤ ESR ≤ 10 Ω Ground; connected to pin 2 Data Sheet 2 Rev. 1.0, 2004-01-01 TLE 4296 Temperature Control Saturation Control and Protection Circuit 4 Q Ι 3 Band-GapReferenz + 1 INH 2,5 GND AEB02312 Figure 2 Block Diagram Data Sheet 3 Rev. 1.0, 2004-01-01 TLE 4296 Table 2 Absolute Maximum Ratings -40 °C < Tj < 150 °C Parameter Input Voltage Current Output Voltage Current Inhibit Voltage Current Current Temperatures Junction temperature Storage temperature Thermal Resistances Junction pin Junction ambient1) Symbol Limit Values Min. Max. 45 – 30 – 45 * 5 V mA V mA V – internally limited – internally limited – * internally limited -0.3 V < VI < 45 V; tp < 1 ms – – measured to pin 5 zero airflow zero heat sink area Unit Remarks VI II VQ IQ VINH IINH IINH -42 – -6 – -42 -500 -5 µA mA Tj Tstg Rthj-pin Rthja -40 -50 – – 150 150 30 179 °C °C K/W K/W 1) Worst case regarding peak temperature. Note: Maximum ratings are absolute ratings; exceeding any one of these values may cause irreversible damage to the integrated circuit. Data Sheet 4 Rev. 1.0, 2004-01-01 TLE 4296 Table 3 Parameter Input voltage Operating Range Symbol Limit Values Min. Max. 45 45 45 40 150 V V V V TLE 4296 GV30 TLE 4296 GV33 TLE 4296 GV50 – – 4.0 4.0 5.5 -0.3 -40 Unit Remarks Inhibit voltage Junction temperature VI VI VI VINH Tj °C Data Sheet 5 Rev. 1.0, 2004-01-01 TLE 4296 Table 4 Electrical Characteristics VI = 13.5 V; VINH > +2.5 V; -40 °C < Tj < 150 °C; unless otherwise specified Parameter Output voltage V30 version Output voltage V30 version Output voltage V33 version Output voltage V33 version Output voltage V50 version Output voltage V50 version Output current limitation Drop voltage Output capacitor Current consumption Iq = II - IQ Current consumption Iq = II - IQ Quiescent current (stand-by) Iq = II - IQ Quiescent current (stand-by) Iq = II - IQ Load regulation Line regulation Symbol Limit Values Min. Typ. 3.0 3.0 3.30 3.30 5.00 5.00 – 0.25 – 2 110 0 Max. 3.12 3.12 3.43 3.43 5.20 5.20 – 0.30 – 4.5 170 1 V V V V V V mA V 1 mA < IQ < 30 mA VI = 13.5 V 2.88 2.88 3.17 3.17 4.80 4.80 30 – 2.2 – – – Unit Test Condition VQ VQ VQ VQ VQ VQ IQ Vdr CQ Iq Iq Iq IQ = 10 mA 4 V < VI < 40 V 1 mA < IQ < 30 mA VI = 13.5 V IQ = 10 mA 4.3 V < VI < 40 V 1 mA < IQ < 30 mA VI = 13.5 V IQ = 10 mA 6 V < VI < 40 V 1) IQ = 20 mA1) 3 Ω ≤ ESR ≤ 10 Ω at 100 kHz µF mA IQ < 30 mA IQ < 1 mA; Tj < 85 °C VINH = 0.4 V; Tj < 85 °C VINH = 0.4 V µA µA Iq ∆VQ – 0 5 µA – – 10 5 20 20 mV mV 1 mA < IQ < 25 mA; Tj = 25 °C ∆VQ VI = (VQ,nom + 0.5 V) to 36 V IQ = 5 mA; Tj = 25 °C Data Sheet 6 Rev. 1.0, 2004-01-01 TLE 4296 Table 4 Electrical Characteristics (cont’d) VI = 13.5 V; VINH > +2.5 V; -40 °C < Tj < 150 °C; unless otherwise specified Parameter Power-Supply-RippleRejection Logic Inhibit Input Inhibit, Turn-on voltage Inhibit, Turn-off voltage H-input current L-input current Symbol Limit Values Min. Typ. 60 Max. – dB – Unit Test Condition PSRR fr = 100 Hz; Vr = 0.5 Vpp VQ > 0.95 VQ,nom VQ > 0.1 V VINH = 5 V VINH = 0 V VINH, high VINH, low IINH, high IINH, low – 0.4 – -2 – – 8 – 2.2 – 12 2 V V µA µA 1) Measured when the output voltage VQ has dropped 100 mV from the nominal value. Data Sheet 7 Rev. 1.0, 2004-01-01 TLE 4296 Typical Performance Characteristics Output Voltage VQ versus Input Voltage VI 10 AED03348.VSD Current Consumption Iq versus Input Voltage VI 1000 AED03347.VSD VQ V 8 VINH = 5 V RL = 1 kΩ Iq µA 800 VINH = 5 V 6 GV50 4 600 GV33 GV30 400 RL = 1 kΩ 2 200 RL = 5 kΩ 0 0 2 4 6 8 V 10 0 0 10 20 30 40 V 50 VI VI Data Sheet 8 Rev. 1.0, 2004-01-01 TLE 4296 V Q ,nom + 0.5 V to 45 V CΙ 100 nF Inhibit Ι 3 4 Q 3.0V / 3.3V / 5.0V TLE 4296 G INH CQ 2.2 µF RQ 3.3 Ω AES02313 1 2,5 GND Figure 3 Application Circuit Application Information In the TLE 4296 G the output voltage is divided and compared to an internal reference of 2.5 V typical. The regulation loop controls the output to achieve a stabilized output voltage. Figure 3 shows a typical application circuit. In order to maintain the stability of the control loop the TLE 4296 G output requires an output capacitor CQ of at least 2.2 µF with an ESR of max. 10 Ω and min. 3 Ω. It is recommended to use tantalum (e.g. the EPCOS 3.3 µF / 16V B45196P3335M209 or 4.7 µF / 10 V B45196-P2475M109) or a multi layer ceramic capacitor with a series resistor in order to cover these limits over the full operating temperature range of -40 °C to 150 °C. At the input of the regulator an input capacitor is necessary for compensating line influences (100 nF ceramic capacitor recommended). A resistor of approx. 1 Ω in series with CI, can damp any oscillation occurring due the input inductivity and the input capacitor. Data Sheet 9 Rev. 1.0, 2004-01-01 TLE 4296 Package Outlines B 1.2 +0.1 -0.05 2.9 ±0.2 (2.2) (0.3) 1.1 max 0.1 max 2.6 max 0.25 min (0.4) 1) (0.13) 0.3 +0.1 -0.05 0.6 +0.1 -0.05 0.95 1.9 0.25 M 1) 0.15 +0.1 -0.06 0.20 M A B Contour of slot depends on profile of gull-wing lead form 10˚max 1.6 ±0.1 (0.23) +0.2 acc. to DIN 6784 1) 10˚max A GPW05997 Figure 4 P-SCT595-5 (Plastic Small Outline) You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet 10 Dimensions in mm Rev. 1.0, 2004-01-01 Edition 2004-01-01 Published by Infineon Technologies AG, St.-Martin-Strasse 53, 81669 München, Germany © Infineon Technologies AG 2004. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.