SEMB13

SEMB13 PNP Silicon Digital Transistor Array Preliminary data • Switching circuit, inverter, interface circuit, driver circuit • Two ( galvanic) internal isolated Transistors with good matching in one package • Built in bias resistors ( R1=4,7kΩ, R2 =47kΩ) C1 6 B2 5 E2 4 4 5 3 6 1 2 R2 R1 TR1 R2 1 E1 2 B1 3 C2 EHA07173 TR2 R1 Type Marking Pin Configuration Package SEMB13 Maximum Ratings Parameter WB 1=E1 2=B1 3=C2 4=E2 5=B2 6=C1 SOT666 Symbol VCEO VCBO VEBO Vi(on) IC Ptot Tj Tstg Value 50 50 5 15 100 250 150 -65 ... 150 Unit V Collector-emitter voltage Collector-base voltage Emitter-base voltage Input on Voltage DC collector current Total power dissipation, TS = 75 °C Junction temperature Storage temperature Thermal Resistance Junction - soldering point 1) mA mW °C RthJS ≤ 300 K/W 1For calculation of R thJA please refer to Application Note Thermal Resistance 1 Feb-26-2004 SEMB13 Electrical Characteristics at TA=25°C, unless otherwise specified Parameter DC Characteristics Collector-emitter breakdown voltage IC = 100 µA, IB = 0 Collector-base breakdown voltage IC = 10 µA, IE = 0 Collector cutoff current VCB = 40 V, IE = 0 Emitter cutoff current VEB = 5 V, IC = 0 DC current gain 1) IC = 5 mA, VCE = 5 V Collector-emitter saturation voltage1) IC = 10 mA, IB = 0.5 mA Input off voltage IC = 100 µA, VCE = 5 V Input on Voltage IC = 2 mA, VCE = 0.3 V Input resistor Resistor ratio R1 R1/R2 3.2 0.09 4.7 0.1 6.2 0.11 kΩ Vi(on) 0.5 1.4 Vi(off) 0.4 0.8 VCEsat 0.3 V hFE 70 IEBO 155 µA ICBO 100 nA V(BR)CBO 50 V(BR)CEO 50 V Symbol min. Values typ. max. Unit AC Characteristics Transition frequency IC = 10 mA, VCE = 5 V, f = 100 MHz Collector-base capacitance VCB = 10 V, f = 1 MHz Ccb 3 pF fT 160 MHz 1) Pulse test: t < 300µs; D < 2% 2 Feb-26-2004 SEMB13 DC Current Gain hFE = f (I C) VCE = 5V (common emitter configuration) 10 3 Collector-Emitter Saturation Voltage VCEsat = f (IC), hFE = 20 10 2 mA hFE 10 2 IC 10 1 10 1 10 0 -1 10 0 1 10 10 mA 10 2 10 0 0 0.2 0.4 0.6 V 1 IC VCEsat Input on Voltage Vi(on) = f (IC ) VCE = 0.3V (common emitter configuration) 10 2 Input off voltage Vi(off) = f (IC ) VCE = 5V (common emitter configuration) 10 1 mA mA 10 0 10 1 IC IC 10 -1 10 0 10 -2 10 -1 -1 10 10 0 10 1 V 10 2 10 -3 0 0.2 0.4 0.6 V 1 Vi(on) Vi(off) 3 Feb-26-2004 SEMB13 Total power dissipation P tot = f (TS) 300 mW Ptot 200 150 100 50 0 0 15 30 45 60 75 90 105 120 °C 150 TS Permissible Pulse Load RthJS = f (tp) Permissible Pulse Load Ptotmax / PtotDC = f (tp) 10 3 K/W 10 3 10 2 Ptotmax/ PtotDC RthJS 10 2 10 1 10 0 0.5 0.2 0.1 0.05 0.02 0.01 0.005 D=0 10 1 D=0 0.005 0.01 0.02 0.05 0.1 0.2 0.5 10 -1 -7 10 10 -6 10 -5 10 -4 10 -3 10 -2 s 10 0 10 0 -7 10 10 -6 10 -5 10 -4 10 -3 10 -2 s 10 0 tp tp 4 Feb-26-2004