TLE4250-2G

Data sheet, Rev. 1.0, July 2007 TLE4250-2 Low Dropout Voltage Tracking Regulator Automotive Power Low Dropout Voltage Tracking Regulator TLE4250-2 1 Features • • • • • • • • • • • • • • Overview 50 mA Output Current Capability Tiny SMD-Package PG-SCT595-5 with lowest thermal resistance Low Output Tracking Tolerance Stable with Small Ceramic Output Capacitor Low Dropout Voltage Combined Reference / Enable Input Low Current Consumption in Stand-by Mode Maximum Input Voltage -42 V ≤ VI ≤ +45 V Reverse Polarity Protection Output Short Circuit Proof to Ground and Supply Overtemperature Protection Temperature Range -40 °C ≤ Tj ≤ 150 °C Green Product (RoHS compliant) AEC Qualified PG-SCT595-5 Functional Description The TLE4250-2 is a monolithic integrated low dropout voltage tracker in a tiny SMD package PG-SCT595-5 with excellent thermal resistance. It is designed to supply off-board loads (e.g. sensors) in automotive environment. The IC protects itself in case of overload, overtemperature, reverse polarity as well as output short circuit to battery and ground. Supply voltages up to VI = 45 V are regulated to a reference voltage applied at the adjust input “ADJ” with high accuracy. The output “Q” is able to drive loads up to 50 mA. In order to reduce the quiescent current to a minimum, the TLE4250-2 can be switched to stand-by mode by setting the adjust/enable input “ADJ/EN” to “low”. Type TLE4250-2G Data sheet Package PG-SCT595-5 2 Marking 52 Rev. 1.0, 2007-07-24 TLE4250-2 Block Diagram 2 Block Diagram TLE 4250-2 Regulated Output Voltage Supply I Q CI ADJ/EN Internal Supply Saturation Control Current Limitation Temp. Protection CQ off-board load Voltage divider optional Reference ADJ/EN BlockDiagram.vsd GND Figure 1 Block Diagram and Simplified Typical Application 3 3.1 Pin Configuration Pin Assignment ADJ/EN GND I 1 5 2 3 4 Pi no ut.v s d GND Q Figure 2 Pin Configuration Package PG-SCT595-5 3.2 Pin 1 Pin Definitions and Functions Symbol ADJ/EN Function Adjust / Enable. Connect the reference to this pin. A low signal disables the IC; a high signal switches it on. The reference voltage can be connected directly or by a voltage divider for lower output voltages. For compensating line influences, a capacitor close to the IC pins is recommended. Ground Reference. Internally connected to Pin 5. Connect to heatsink area. Input. IC supply. For compensating line influences, a capacitor close to the IC pins is recommended. Tracker Output. Block to GND with a capacitor close to the IC terminals, respecting capacitance and ESR requirements given in the table “Functional Range”. Ground Reference. Internally connected to Pin 2. Connect to heatsink area. 3 Rev. 1.0, 2007-07-24 2 3 4 GND I Q 5 GND Data sheet TLE4250-2 General Product Characteristics 4 4.1 General Product Characteristics Absolute Maximum Ratings Absolute Maximum Ratings 1) -40 °C ≤ Tj ≤ 150 °C; all voltages with respect to ground (unless otherwise specified). Pos. Voltages 4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.1.7 Input voltage Output voltage Adjust / Enable Input Junction Temperature Storage Temperature ESD Resistivity Parameter Symbol Limit Values Min. Max. 45 40 40 150 150 3 2 V V V °C °C kV kV – – – – – HBM2) CDM3) Unit Conditions VI VQ VADJ/EN Tj Tstg VESD,HBM VESD,CDM -42 -1 -0.3 -40 -50 -3 -2 Temperatures ESD Susceptibility 1) Not subject to production test, specified by design. 2) ESD susceptibility, Human Body Model “HBM” according to EIA/JESD 22-A114B 3) ESD susceptibility, Charged Device Model “CDM” according to EIA/JESD22-C101 or ESDA STM5.3.1 Note: Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note: Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. Data sheet 4 Rev. 1.0, 2007-07-24 TLE4250-2 General Product Characteristics 4.2 Pos. 4.2.1 4.2.1 4.2.2 4.2.3 4.2.4 Functional Range Parameter Input Voltage Adjust / Enable Input Voltage (Voltage Tracking Range) Junction Temperature Output Capacitor Requirements Symbol Limit Values Min. Max. 40 36 150 – 3 V V °C µF Ω – – – – 1) – 2) 4 2.5 -40 1 – Unit Conditions VI VADJ/EN Tj CQ ESRCQ 1) The minimum output capacitance requirement is applicable for a worst case capacitance tolerance of 30% 2) relevant ESR value at f = 10 kHz Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the related electrical characteristics table. 4.3 Pos. 4.3.5 4.3.1 4.3.2 4.3.3 4.3.4 Thermal Resistance Parameter Junction to Ambient Symbol Min. Limit Value Typ. 81 217 117 103 30 Max. – – – – – K/W K/W K/W K/W K/W 2s2p board1) Footprint only2) 300 mm2 PCB heatsink area2) 600 mm2 PCB heatsink area2) Pins 2, 5 fixed to TA – – – – Junction to Soldering Point Unit Conditions RthJA RthJSP – 1) Specified RthJA value is according to JESD51-2,-5,-7 at natural convection on FR4 2s2p board; The product (chip+package) was simulated on a 76.2 x 114.3 x 1.5 mm board with 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu). Where applicable a thermal via array under the package contacted the first inner copper layer. 2) Package mounted on PCB FR4; 80 x 80 x 1.5 mm; 35 µm Cu, 5 µm Sn; horizontal position; zero airflow. Not subject to production test; specified by design. Data sheet 5 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics 5 5.1 Electrical Characteristics Tracking Regulator The output voltage VQ is controlled by comparing it to the voltage applied at pin ADJ/EN and driving a PNP pass transistor accordingly. The control loop stability depends on the output capacitor CQ, the load current, the chip temperature and the poles/zeros introduced by the integrated circuit. To ensure stable operation, the output capacitor’s capacitance and its equivalent series resistor ESR requirements given in the table “Functional Range” have to be maintained. For details see also the typical performance graph “Output Capacitor Series Resistor ESRCQ vs. Output Current IQ”. Also, the output capacitor shall be sized to buffer load transients. An input capacitor CI is recommended to buffer line influences. Connect the capacitors close to the IC terminals. Protection circuitry prevent the IC as well as the application from destruction in case of catastrophic events. These safeguards contain output current limitation, reverse polarity protection as well as thermal shutdown in case of overtemperature. In order to avoid excessive power dissipation that could never be handled by the pass element and the package, the maximum output current is decreased at high input voltages. The overtemperature protection circuit prevents the IC from immediate destruction under fault conditions (e. g. output continuously short-circuited) by reducing the output current. A thermal balance below 200 °C junction temperature is established. Please note that a junction temperature above 150 °C is outside the maximum ratings and reduces the IC lifetime. The TLE4250-2 allows a negative supply voltage. However, several small currents are flowing into the IC. For details see electrical characteristics table and typical performance graphs. The thermal protection circuit is not operating during reverse polarity condition. Table 1 Pos. 5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.1.7 5.1.8 Electrical Characteristics Tracking Regulator Parameter Output Voltage Tracking Accuracy Symbol ∆ VQ -5 -25 -25 Load Regulation steady-state Line Regulation steady-state Power Supply Ripple Rejection Dropout Voltage |dVQ,load| |dVQ,line| – – – – 51 Limit Values Min. Typ. – – – – – 48 100 85 Max. 5 25 25 15 10 – 300 120 mV mV mV mV mV dB mV mA 1 mA ≤ IQ ≤ 10 mA; 6 V ≤ VI ≤ 1 6 V 1 mA ≤ IQ ≤ 50 mA; 6 V ≤ VI ≤ 2 8 V 1 mA ≤ IQ ≤ 10 mA; 6 V ≤ VI ≤ 40V Unit Conditions VI = 13.5 V; VADJ/EN ≥ 2.5 V; -40 °C ≤ Tj ≤ 150 °C; all voltages with respect to ground (unless otherwise specified). IQ = 1 mA to 30 mA; VI = 6 V to 40 V; IQ = 10 mA fripple = 100 Hz; Vripple = 1 Vpp 1) IQ = 10 mA VADJ ≥ 4 V 2) VQ = (VADJ - 0.1 V) PSRR Vdr IQ,max Vdr = VI - VQ Output Current Limitation Data sheet 6 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics Table 1 Pos. 5.1.9 Electrical Characteristics Tracking Regulator Parameter Reverse Current Symbol Limit Values Min. Typ. -1 Max. – mA -5 Unit Conditions VI = 13.5 V; VADJ/EN ≥ 2.5 V; -40 °C ≤ Tj ≤ 150 °C; all voltages with respect to ground (unless otherwise specified). IQ 5.1.10 Reverse Current at Negative Input Voltage II -10 -2 – mA VI = 0 V; VQ = 16 V; VADJ = 5 V VI = -16 V; VQ = 0 V; VADJ = 5 V Overtemperature Protection: 5.1.11 Junction Temperature Equilibrium Tj,eq 151 – 200 °C Tj increasing due to power dissipation generated by the IC 1) 1) Parameter not subject to production test; specified by design. 2) Measured when the output voltage VQ has dropped 100 mV from its nominal value. Data sheet 7 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics Typical Performance Characteristics Tracking Regulator VADJ/EN = 5 V (unless otherwise noted) Output Voltage VQ vs. Adjust Voltage VADJ VQ-VADJ.vsd Output Voltage VQ vs. Input Voltage VI VQ-VI.vsd V Q [ V] VI = 13.5 V V Q [ V] VI = 13.5 V 4 4 Vdr 3 3 2 2 T j = 150 °C 1 T j = -40 °C Tj = -40 °C 1 T j = 150 °C 1 2 3 4 1 3 5 7 VADJ [ V] Maximum Output Current IQ vs. Input Voltage VI 120 IQ [mA] VADJ = 5 V Tj = 25 °C 80 Tj = 125 °C 0.3 VI [ V] Line Regulation dVQ,line vs. Input Voltage Change dVI) SOA.VSD dVQ-dVI.vsd ∆ VQ [ mV] VI,initial = 6 V VADJ = 5 V IQ = 5 mA 60 0.2 40 0.1 20 0 steady-state condition 0 10 20 30 40 VI [V] 0 5 10 15 20 25 30 35 40 ∆VI [V] Data sheet 8 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics Typical Performance Characteristics Tracking Regulator VADJ/EN = 5 V (unless otherwise noted) Load Regulation dVQ,line vs. Output Current Change dIQ dVQ-dIQ.vsd Output Capacitor Series Resistor ESRCQ vs. Output Current IQ 10 ESR-IQ.vsd ∆ VQ [ mV] IQ,initial = 1 m A VADJ = 5 V ESR CQ [Ω] C Q = 2.2 µF -2 T j = 25 °C 1 C Q = 1 µF -4 Tj = 125 °C -6 0.1 Stable Region -8 steady-state condition 0 12 24 36 48 0.01 0 10 20 VI < 28 V -40 °C < T j < 150 °C 30 40 50 ∆ΙQ [mA] Line Transient Response dVI-reponse.vsd IQ [mA] Load Transient Response dIQresponse.vsd ∆ VQ [mV] ∆ VQ [mV] 0 0 -20 -40 -50 [V] 16 VI I Q = 5 mA C Q = 2.2 µF Ceramic [mA] 30 ΙQ VI = 13.5 V VADJ = 5 V C Q = 2.2 µF Ceramic 9 0 20 40 60 80 5 0 20 40 60 80 t [µs] t [µs] Data sheet 9 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics Typical Performance Characteristics Tracking Regulator VADJ/EN = 5 V (unless otherwise noted) Tracking Accuracy ∆VQ vs. Junction Temperature Tj [mV] Dropout Voltage Vdr vs. Output Current IQ dVQ-Tj.vsd Vdr-IQ_log.vsd ∆VQ V dr [ mV] 8 T j = 150 °C IQ = 50 mA T j = 25 °C 100 4 0 IQ = 1 m A -4 -40 -20 0 20 40 60 80 100 120 140 10 1 10 50 T j [°C] Dropout Voltage Vdr vs. Junction Temperature Tj Vdr-Tj.vsd I Q [mA] Output Current Limitation IQ,max vs. Output Voltage VQ IQmax-VQ.vsd V dr [mV] VI = 13.5 V VADJ = 5 V 5 VQ [V] 250 200 3 Tj = 125°C Tj = 25°C 150 IQ = 10 mA 2 100 1 -40 -20 0 20 40 60 80 100 120 140 0 20 40 60 80 100 IQ [mA] T j [°C] Data sheet 10 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics Typical Performance Characteristics Tracking Regulator VADJ/EN = 5 V (unless otherwise noted) Reverse Output Current IQ vs. Output Voltage VQ +0.5 IQ-VQ.vsd Reverse Current II vs. Input Voltage VI +0.5 II-VI.vsd I Q [mA] VI = 0 V V ADJ = 5 V I I [mA] VQ = 0 V VADJ = 5 V -0.5 -0.5 -1 -1 T j = -40 °C T j = 150 °C T j = -40 °C -1.5 -1.5 T j = 150 °C -2 -2 0 8 16 24 32 -32 -24 -16 -8 0 VQ [V] Power Supply Ripple Rejection PSRR 60 PSRR.vsd VI [V] PSRR [dB] IQ = 5 m A 40 30 20 10 VRIPPLE = 1 V VIN = 13.5 V C Q = 2.2 µF Ceramic T j = 25 °C 0.1 1 10 100 0.01 f [ kHz] Data sheet 11 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics 5.2 Table 2 Pos. 5.2.1 5.2.2 5.2.3 5.2.4 Current Consumption Electrical Characteristics Current Consumption Parameter Quiescent Current Stand-by Mode Current Consumption Iq = II - IQ Current Consumption Dropout Region; Iq = II - IQ Symbol Min. Limit Values Typ. 10 140 3 1 Max. 20 200 5 2 µA µA mA mA – – – – Unit Conditions VI = 13.5 V; VADJ/EN ≥ 2.5 V; -40 °C ≤ Tj ≤ 150 °C; all voltages with respect to ground (unless otherwise specified). Iq1 Iq2 Iq3 VADJ/EN ≤ 0.4 V; Tj ≤ 85 °C IQ ≤ 1 mA; IQ ≤ 30 mA; VADJ = VI = 5 V; IQ = 0 m A Typical Performance Characteristics Current Consumption VADJ/EN = 5 V (unless otherwise noted) Current Consumption Iq1, Iq2 vs. Junction Temperature Tj Iq-Tj.vsd Current Consumption Iq2 vs. Output Current IQ Iq-IQ.vsd I q2 [ mA] I Q = 30 mA I q [ mA] V EN/ADJ = 5 V VI = 9 V VI = 13.5 V 1 VI = 13.5V VEN/ADJ = 5 V IQ = 1 m A VI = 32 V 1 0.1 Iq1 [ µA] 16 V I = 13.5V V EN/ADJ = 0 V VI = 32 V 12 -40 -20 0 20 40 60 80 100 120 140 0.1 1 10 50 Tj [°C] IQ [mA] Data sheet 12 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics Current Consumption Iq2 vs. Input Voltage VI 12 Iq-VI.vsd I q [ mA] VADJ = 5 V 8 IQ = 50 mA 6 4 IQ = 30 mA IQ = 10 mA 6 10 14 18 22 24 2 VI [V] Data sheet 13 Rev. 1.0, 2007-07-24 TLE4250-2 Electrical Characteristics 5.3 Adjust / Enable Input In order to reduce the quiescent current to a minimum, the TLE4250-2G can be switched to stand-by mode by setting the adjust/enable input “ADJ/EN” to “low”. Table 3 Electrical Characteristics Adjust / Enable VI = 13.5 V; VADJ ≥ 2.5 V; -40 °C ≤ Tj ≤ 150 °C; all voltages with respect to ground, positive current flowing into pin (unless otherwise specified). Pos. 5.3.1 5.3.2 5.3.3 Parameter Adjust / Enable Input Current Adjust / Enable Low Signal Valid Adjust / Enable High Signal Valid (Tracking Region) Symbol Min. Limit Values Typ. 0.1 – – Max. 0.5 0.4 36 µA V V – – 2.5 Unit Conditions IADJ VADJ,low VADJ,high VADJ = 5 V; VQ = 0 V ; |VQ - VADJ| < 25 mV; Typical Performance Characteristics Adjust / Enable Input VADJ/EN = 5V (unless otherwise noted) Startup Sequence 4250-2_startup.vsd V [ V] Overshoot depends on load current, CQ , ESR CQ 4 VADJ 3 2 dVQ / dt = (IQ,max-I Load ) / C Q 1 0 20 40 60 80 100 120 140 t [µs] Data sheet 14 Rev. 1.0, 2007-07-24 TLE4250-2 Package Outlines 5 Package Outlines 2.9 ±0.2 (2.2) 1.2 +0.1 -0.05 B (0.3) (0.4) 1) 1.1 MAX. 0.1 MAX. 2.5 ±0.1 0.25 ±0.1 10˚ MAX. (0.23) 1) 1 2 3 0.3 +0.1 -0.05 +0.1 0.6 -0.05 10˚ MAX. 0.15 +0.1 -0.06 0.2 M A 0.95 1.9 0.25 M B A 1) Contour of slot depends on profile of gull-wing lead form GPW05997 Figure 3 Outline PG-SCT595-5 1.9 2.9 0.4 0.75 0.95 HLG09053 0.4 0.75 0.95 HLG09090 Reflow Soldering Wave Soldering Figure 4 Footprint PG-SCT595-5 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages Data sheet 16 1.6 1.45 1.3 MIN. 2.3 1.3 2.3 1.3 1.6 ±0.1 5 4 (0.13) +0.2 acc. to DIN 6784 Dimensions in mm Rev. 1.0, 2007-07-24 TLE4250-2 Revision History 6 Revision Rev. 1.0 Revision History Date 2007-07-24 Changes • Final Datasheet Initial Version Data sheet 17 Rev. 1.0, 2007-07-24 Edition 2007-07-24 Published by Infineon Technologies AG 81726 Munich, Germany © 2007 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.