TLE4305

Voltage-Current Regulator TLE 4305 Features • • • • • • • • • • • • Wide supply voltage operation range Wide ambient temperature operation range Minimized external circuitry High voltage regulation accuracy High current limit regulation accuracy Low temperature drift Independent voltage- current-loop compensation Internal fixed amplification Fully temperature compensated current- and voltage OTA (operational transconductance amplifier) SMD package Industrial type Green Product (RoHS compliant) Functional Description The TLE 4305 G is specifically designed to control the output voltage and the output current of a switch mode power supply. Independent compensation networks for the voltage- and for the current-loop can be realized by external circuitry. The device contains a high accuracy bandgap reference voltage, two operational trans conductance amplifier (OTA), an opto-coupler driver output stage and an high-voltage bias circuit. The device is based on Infineons double isolated power line technology DOPL which allows to produce high precision bipolar voltage regulators with breakdown voltages up to 45 V. Type TLE 4305 G Data Sheet Package PG-DSO-8 1 Rev. 2.2, 2008-11-17 TLE 4305 S VSE OUT CSE 1 2 3 4 8 7 6 5 CRE VCO CCO GND AEP02887 Figure 1 Table 1 1 2 S VSE Pin Configuration (top view) Pin Definitions and Functions Supply voltage; external blocking capacitor necessary (see Figure 4). Voltage Sense Input; non inverting with respect to voltage compensation VCO; internal compared with the high accuracy bandgap-reference (typ. 2.5 V). Output; NPN emitter follower output with an internal series resistor of 1 kΩ; controlled by the potential of VCO or CCO; output voltage is internally clamped therefore the output current is internally limited. Current Sense Input 1; connected to an internal voltage divider (reference to the inverting input of the current OTA; see Figure 7). Ground; reference potential unless otherwise specified. Current Compensation Output; internal series resistor to the current-OTA output (typ. 1 kΩ); amplification internal temperature compensated; current loop compensation can be done by an external capacitor to GND. Voltage Compensation Output; internal series resistor to the voltage-OTA output (typ. 1 kΩ); amplification internal temperature compensated; voltage loop compensation can be done by an external capacitor to GND. Current-OTA Reference Input; current sense reference input; non inverting input of the current-OTA. Pin No. Symbol Function 3 OUT 4 5 6 CSE GND CCO 7 VCO 8 CRE Data Sheet 2 Rev. 2.2, 2008-11-17 TLE 4305 TLE 4305G Biasing and BandgapReference S 1 RVC 1k 7 VCO V-OTA VSE 2 3 OUT VREF VREF RI1 CSE 4 Driver Control Logic C-OTA 1k RI2 2k 25 k RCC 1k 6 CCO CRE 8 5 GND AEB02879 Figure 2 Block Diagram Data Sheet 3 Rev. 2.2, 2008-11-17 TLE 4305 Table 2 Parameter Voltages Absolute Maximum Ratings Symbol Limit Values Min. Max. 45 7 7 V V V – – – Unit Remarks Supply voltage Input voltages Output voltages Currents Output current Output current ESD-Protection Human Body Model Temperatures Junction temperature Storage temperature Thermal Resistances Junction ambient VS -0.3 VVSE; VCSE; -0.3 VCRE VOUT; VVCO; -0.3 VCCO IOUT IVCO; ICCO VESD -5 -0.5 -1.5 3 0.5 1.5 mA mA kV – – according JEDEC JESD22-A114 – – – Tj Tstg Rthj-a -40 -50 – 150 150 200 °C °C K/W Note: Stresses above those listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 3 Parameter Supply voltage Junction temperature Operating Range Symbol Limit Values Min. Max. 42 150 V °C – – 8 -40 Unit Remarks VS Tj Note: In the operating range, the functions given in the circuit description are fulfilled. Data Sheet 4 Rev. 2.2, 2008-11-17 TLE 4305 Table 4 Electrical Characteristics 8 V < VS < 42 V; -40 °C < Tj < 150 °C; IOUT = 0 mA; all voltages with respect to ground; positive current defined flowing into pin; unless otherwise specified. Parameter Current Consumption Supply current Supply current Supply current Supply current Voltage at pin CSE Voltage at pin CSE Symbol Limit Values Min. Typ. 1 – 1.5 – 2.50 Max. 1.5 2 2.5 4 2.55 mA mA mA mA V Unit Test Condition IS IS IS IS VCSE,ref – – – – 2.45 VS = 9 V; Tj = 25 °C VS = 9 V VS = 42 V; Tj = 25 °C VS = 42 V Tj = 25 °C; ICSE = 0 mA ICSE = 0 mA Reference Voltage (measurable at pin CSE) VCSE,ref 2.425 – Temperature Coefficient ∆VCSE,ref -50 – Voltage-OTA; Pin VSE and VCO Input voltage threshold Input offset voltage Transconductance 2.575 V 50 – 5 – – – -0 -25 150 ppm/K – V mV mS kΩ kHz µA µA µA VVSE VVSE,io – -5 – – – -1.0 -150 25 VREF – 1 2 500 -0.2 -60 60 gV Output series resistor RVCO Gain Bandwidth Product BV Input current IVSE Output current; IVCO source IVCO = 0 mA; VVCO = 2.5 V IVCO = 0 mA; VVCO = 2.5 V gV = ∆IVCO / ∆UVSE – – Output current; sink IVCO VVSE = 0 V VVSE = 5 V; VVCO = 2.5 V VVSE = 0 V; VVCO = 2.5 V Data Sheet 5 Rev. 2.2, 2008-11-17 TLE 4305 Table 4 Electrical Characteristics (cont’d) 8 V < VS < 42 V; -40 °C < Tj < 150 °C; IOUT = 0 mA; all voltages with respect to ground; positive current defined flowing into pin; unless otherwise specified. Parameter Symbol Limit Values Min. Current-OTA; Pin CSE and CCO Input voltage threshold Transconductance Typ. -200 1 2 500 -100 -60 Max. -190 – – – -50 -25 mV mS kΩ kHz µA µA Unit Test Condition VCSE -210 – – – -200 -150 gC Output series resistor RCCO Gain Bandwidth Product BC Input current ICSE Output current; ICCO source Output current; sink ICCO = 0 mA; VCCO = 2.5 V gC = ∆ICCO / ∆UCSE – – ICCO 25 60 150 µA VCSE = 0 V VCRE = 2.5 V; VCSE = 0 V; VCCO = 2.5 V VCRE = 0 V; VCSE = 0 V; VCCO = 2.5 V VCSE = 0 V; VCRE = 0 V VVSE = 5 V; ROUT-GND = 22 kΩ 10 V < VS < 42 V; VVSE = 5 V; VOUT = 0 V 8 V < VS < 10 V; VVSE = 5 V; VOUT = 0 V Current Reference Input Pin CRE Input Current Output Pin OUT Output voltage limit Output current; voltage loop controlled Output current; voltage loop controlled ICRE -1.0 -0.2 -0 µA VOUT IOUT 3 -8.5 4 -4 5.5 -2 V mA IOUT -4.5 -2.0 -0.5 mA Data Sheet 6 Rev. 2.2, 2008-11-17 TLE 4305 Table 4 Electrical Characteristics (cont’d) 8 V < VS < 42 V; -40 °C < Tj < 150 °C; IOUT = 0 mA; all voltages with respect to ground; positive current defined flowing into pin; unless otherwise specified. Parameter Output current; current loop controlled Symbol Limit Values Min. Typ. -4 Max. -2 mA 10 V < VS < 42 V; VCSE = 0 V; VCRE = 5 V; VOUT = 0 V 8 V < VS < 10 V; VCSE = 0 V; VCRE = 5 V; VOUT = 0 V -8.5 Unit Test Condition IOUT Output current; current loop controlled IOUT -4.5 -2.0 -0.5 mA Note: The listed characteristics are ensured over the operating range of the integrated circuit. Typical characteristics specify mean values expected over the production spread. If not otherwise specified, typical characteristics apply at TA = 25 °C and the given supply voltage. Data Sheet 7 Rev. 2.2, 2008-11-17 TLE 4305 Application Information The TLE 4305 is a voltage and current regulator for Switch Mode Power Supply (SMPS) applications. It controls the output voltage and the maximum output current of a power supply unit. It is located on the secondary side of the SMPS. The TLE 4305 consists of a output voltage control loop and a current control loop. The driver is especially designed to drive the opto-isolator. The current controls the PWM duty cycle of the primary regulator. Isolated SMPS Switch mode power supply (SMPS) systems generate a regulated DC voltage VQ that is isolated from the primary side. A maximum output current IQmax is defined to protect the system in any load failures. Line SMPS with Cool Set Secondary Regulator with TLE 4305 Precise Output Voltage Output Current precise limited Short circuit protected Opto Isolator AES02888 Figure 3 Isolated SMPS Principle The principle of an isolated SMPS is shown in Figure 3. The primary side of the SMPS is supplied by the line. The secondary side supplies a regulated voltage to the load. Primary and secondary side are isolated from each other by the transformer and an opto isolator. A SMPS controller such as the Infineon TDA1683x controls the PWM duty cycle of the output voltage signal. The signal is transmitted by a Transformer with n1:n2 (n: number of windings). On the secondary side a load capacitor is charged. The secondary regulator controls the output voltage VQ and limits the output current. It generates an analog control signal to the primary side through an opto isolator to regulate the PWM duty cycle of the primary signal. The loop is closed through the primary SMPS regulator and the transformer. Simple SMPS defines the output voltage by a voltage divider and a transistor. This requires very precise resistor values and due to the nature of the transistor the control signal is dependent on temperature and device variation. The current limitation has to be done on the primary side with elements suitable for high voltages. Data Sheet 8 Rev. 2.2, 2008-11-17 TLE 4305 SMPS with TLE 4305 Secondary Regulator The TLE 4305 is located on the secondary side of the regulator and controls the output voltage as well as it limits the output current. Voltage and current can be chosen independent from each other by the designer according to the application’s requirements. LS SMPS Primary Side n1 n3 D1 RGL34D n2 TLE 4305G VSE VQ + Line RV1 VS VCO CVCO 10 nF RV2 Cool Set TDA 1683x PWM Duty Cycle = f(VFB) FB CS 100 nF CCO CCCO 10 nF CS2 CL CS1 CRE GND CSE OUT - 470 µF RSense D2 SMS2100 Optocoupler AES02878 Figure 4 Application Circuit (1) (2) VQ = 2.5 V × (RV1 + RV2) / RV2 IQ = 0.2 V / RSense Figure 3 shows the TLE 4305 as SMPS secondary regulator as application circuit. The load capacitor CL is charged by the PWM-signal at the secondary side of the transformer. The diode D2 defines the current flow in the transformer. Data Sheet 9 Rev. 2.2, 2008-11-17 TLE 4305 The TLE 4305 includes an independent voltage control and current control loop. The internal schematic is shown in Figure 2. For IQ < IQmax the voltage control gets priority. If the supply operates in the overcurrent protection mode, the current loop is active and reduces the output voltage with constant output current IQmax. The output voltage/output current curve is shown in Figure 5. Both the current control loop and the voltage control loop are temperature compensated. VQ VQ Voltage Regulator Active Cross Over Current Regulator Active IQmax IQ AED02882 Figure 5 Current and Voltage Limit The voltage or current loop regulator result defines the current into the opto isolator to control the PWM duty cycle. The LED driver is fully integrated, no external components are required. Data Sheet 10 Rev. 2.2, 2008-11-17 TLE 4305 Voltage Control Loop Voltage Loop TLE 4305 from Current Loop VQ Driver Control Logic 1 kΩ OUT RV1 VSE V-OTA RVC 1 kΩ VCO RV2 VREF CVCO 10 nF AES02883 Figure 6 Voltage Loop The voltage loop regulator compares the input voltage VSE to a reference voltage Vref of typical 2.5 V. The difference is attenuated and proportional current drives the opto isolator. The control loop output voltage VQ, pin VSE, pin OUT, opto isolator, primary regulator and the transformer close the loop. To program an output voltage a divider is used. The resistors are chosen according to Equation (5). VVSE = Vref VVSE = VQ × RV2 / (RV1 + RV2) with Vref typical 2.5 V (3) (4) VQ = VVSE × (RV1 + RV2) / RV2 (5) To compensate the voltage loop a 10 nF capacitor should be connected to pin VCO. With the internal 1 kΩ resistor it reduces the overall closed voltage loop’s bandwidth. If the gain of the overall loop has to be adapted to the application’s needs, the output capacitor can be modified accordingly. Data Sheet 11 Rev. 2.2, 2008-11-17 TLE 4305 Current Control Loop Current Loop TLE 4305 from Voltage Loop VREF Driver RI1 RI1 25 k Ω 25 k Ω D2 C-OTA CSE Control Logic 1 kΩ OUT RCC 1 kΩ CCO RSense CRE CCCO 10 nF AES02880 Figure 7 Current Control Loop To detect the current a sense resistor Rsense is placed in the current back-path to the transformer (see Figure 4 and Figure 7). The control operational amplifier compares the voltage at pin CRE to the voltage at the inverting input of the OTA. In an overcurrent condition, the overall closed loop through current loop, opto isolator, primary regulator, transformer and the application reduces the PWM duty cycle to meet the closed loop condition. VCSE - VCRE is typical 200 mV. The current limit is defined by IQmax = 200 mV / Rsense (6) To compensate the overall closed current loop a 10 nF capacitor should be connected to pin VCO. With the internal 1 kΩ resistor it reduces the voltage loop’s bandwidth. As already explained for the voltage loop, the capacitor can be modified according to the overall loop’s bandwidth. To further improve the current control in addition a compensation can be added at pin CRE as shown in Figure 8. Data Sheet 12 Rev. 2.2, 2008-11-17 TLE 4305 Current Loop TLE 4305 from Voltage Loop VQ CCRE 100 nF D2 CSE VREF Driver RI1 RI1 25 k Ω C-OTA Control Logic 1 kΩ OUT RCC 1 kΩ CRE 25 k Ω CCO CCCO 10 nF RSense RCRE 10 k Ω AES02881 Figure 8 Improved Current Control Loop The calculation of the current is identical to the above calculation (Equation (6)). The voltage at resistor RCRE can be neglected (typical 2 mV for 10 kΩ resistor). The resistor RCRE and the Capacitor CCRE improve further the current control loop response. Supply of the TLE 4305 The TLE 4305 is an active circuitry and requires a supply voltage at pin VS. During start up of the supply, there is no energy stored in the load capacitor. Dependent on the required output voltage also during operation the output voltage might be too small. Therefore a second transformer-winding n3 is required. The voltage charges the input capacitor CS though the diode D1. Internally the TLE 4305 generates for input voltages above 8 V a preregulated 6 V internal rail. The device generates biasing currents and reference voltages from this rail. To avoid Ground and VQ-shifts, all GND connections should be connected to one point as well as all VQ-signals. If the application requires more than one voltage linear post-regulators can be used. In the application a choke should be placed in series. An electrolyte or tantalum capacitor of 10 µF to 100 µF should be used in parallel to a 10 to 100 nF ceramic capacitor to filter high frequency noise. The size of the choke and the capacitors depend on the application requirements. Data Sheet 13 Rev. 2.2, 2008-11-17 TLE 4305 Package Outlines 0.35 x 45˚ 1.75 MAX. 0.175 ±0.07 (1.45) 4 -0.21) 0.19 +0.06 C 1.27 0.41+0.1 2) -0.06 0.2 M 0.1 A B 8x B 6 ±0.2 0.64 ±0.25 0.2 M 8 MAX. C 8x GPS01181 8 5 1 4 1) A 5 -0.2 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area Figure 9 PG-DSO-8 (Plastic Dual Small Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet 14 Dimensions in mm Rev. 2.2, 2008-11-17 TLE 4305 Revision History Version Date Changes Rev. 2.2 2008-11-17 Initial version of RoHS-compliant derivate of TLE 4305. Page 4: ESD rating changed to HBM 1.5kV with modified test condition (changed test standard to JEDEC JESD22-A114) Page 1 and Page 14: RoHS compliance statement and Green product feature added Page 1 and Page 14: Package changed to RoHS compliant version Legal Disclaimer updated Data Sheet 15 Rev. 2.2, 2008-11-17 Edition 2008-11-17 Published by Infineon Technologies AG 81726 Munich, Germany © 2008 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.