TLE4307

Power-Charge-Pump and Low-Drop Voltage Regulator TLE 4307 Power Charge Pump Circuit Features • • • • High Current Capability Short Circuit Protection Overtemperature Protection Active Zener Circuit P-TO252-5-1 Very Low Drop Voltage Regulator Features • • • • • 3.3 V or 3.8 V output voltage Low Output Voltage Tolerance High Current Capability 800 mA Short Circuit Protection Overtemperature Protection General Features • Optimized SMD Package Type • TLE 4307 DV33 • TLE 4307 DV38 • New Type Functional Description The TLE 4307 is a monolithic integrated power charge pump with a Low Drop Voltage Regulator. The power charge pump loads an energy storage capacitor at pin C. The voltage regulator supplies 3.3 V or 3.8 V out of this storage capacitor with up to 800 mA output current. The TLE 4307 is intended for use with DC supplies for consumer or industrial applications. Ordering Code Q67006-A9444 Q67006-A9415 Package P-TO252-5-1 (D-PAK) P-TO252-5-1 (D-PAK) Data Sheet Rev. 1.1 1 2000-10-11 TLE 4307 P-TO252-5-1 (D-PAK) GND I C SL Q AEP02792 Figure 1 Pin Configuration (top view) Pin Definitions and Functions Pin No. 1 2 3 4 5 Symbol I C GND SL Q Function Input; Connect to the input voltage source Charge-Pump Output; Connect to the energy reservoir capacitor to GND Ground Slewrate Control Input; a capacitor from this pin to the Input pin I controls the slewrate during recirculation Regulator Output; connect to GND with a capacitor as specified for CQ Data Sheet Rev. 1.1 2 2000-10-11 TLE 4307 TLE 4307 1 Power Charge Pump Very Low-Drop Regulator 5 I Q SL 4 2 C 3 GND AES02793 Figure 2 Block Diagram Circuit Description The TLE 4307 consists of 2 stages, the charge pump and the very low drop voltage regulator. Charge Pump The power stage is used as a switching element, that is driven by a buffer. A current source keeps the power stage on. When the output C of the charge pump reaches VC,off, the power stage is switched off. It is active clamped, when the input I reaches VI,cl. Optional, an external capacity can be connected between pin SL and I to limit the slew rate at the input, when an inductive load drives the IC. Saturation control as a function of the load current prevents any over-saturation of the power element. The regulator is additionally protected against overload and overtemperature. Very Low Drop Regulator The control amplifier compares a reference voltage, made highly accurate by resistance balancing, with a voltage proportional to the output voltage and drives the base of the series PNP transistor via a buffer. Saturation control as a function of the load current prevents any over-saturation of the power element. The regulator is additionally protected against overload and overtemperature. Data Sheet Rev. 1.1 3 2000-10-11 TLE 4307 VLine Vac = 12 V LS = 4 mH RS = 15 Ω 4x1N4001 D1 or B40C800 I1 TLE 4307 Power Charge Pump Very 5Q Low-Drop Regulator VOUT = 3.8 V IOUT = 0.4 A CS 100 pF SL 4 CQ1 CC 470 µF 15 V 2 C 3 GND 220 nF CQ2 22 µF 6.3 V AES02794 Figure 3 Application Example Application Description The IC is meant to be used with a DC power supply. The power charge pump limits the energy that is needed to drive the load at the output Q of the IC. The energy is stored to a capacity CC, connected to pin C. When pin C reaches VC,off, the power charge pump is switched off. Since the power supply consists of the inductance and a parasitic series resistance, the remaining available energy is dissipated in the external power supply and therefore does not stress the IC with this dispensable energy. The very low drop regulator is provided with the energy, stored in CC. The regulator requires an output capacitor CQ for the stability of the regulating circuit. Stability is guaranteed at values above 22 µF and an ESR ≤ 1 Ω within the operating temperature range. Data Sheet Rev. 1.1 4 2000-10-11 TLE 4307 Absolute Maximum Ratings Parameter Symbol Limit Values min. Input Input voltage Input current (during pump cycle) Input current (during active zener operation) Charge-Pump Output Voltage Current Slewrate Input Voltage Current Regulator Output Voltage Current Temperature Junction temperature Storage temperature Thermal Data Junction-ambient max. Unit Notes VI II II – 0.3 –5 –5 VICL – 1000 V mA mA VICL = zener clamp voltage internally limited tp < 1 ms; duty cycle 10% VC IC – 0.3 20 – V mA – internally limited – VSL ISL – 0.3 – 0.5 4.0 0.5 V mA – – VQ IQ – 0.3 25 – V mA – internally limited – Tj TStg – 40 – 50 150 150 °C °C – – Rthj-a Rthj-c – – 70 4 K/W K/W – – Data Sheet Rev. 1.1 5 2000-10-11 TLE 4307 Absolute Maximum Ratings (cont’d) Parameter Symbol Limit Values min. ESD All pins to GND Operating Range Input voltage Output current Junction temperature max. Unit Notes VESD –2 2 kV HBM Model VI II Tj 0 0 – 40 VICL 600 150 V mA °C – – – Data Sheet Rev. 1.1 6 2000-10-11 TLE 4307 Electrical Characteristics VI = 12 V; 40 °C < Tj < 150 °C All voltages with respect to ground; positive current defined flowing into the pin; unless otherwise specified. Parameter Current consumption; Iq = II – IQ Current consumption; Iq = II – IQ Current consumption; Iq = II – IQ Charge Pump Switch off threshold Input Clamp Voltage Current limit Drop voltage; VI – VC Drop voltage; VI – VC Drop voltage; VI – VC Main-Regulator Output voltage Output voltage Current limit Drop voltage; VC – VQ Drop voltage; VC – VQ Drop voltage; VC – VQ Over all Drop voltage; VI – VQ Load regulation Symbol Limit Values min. typ. 1.2 1.4 4 max. 2.5 3.0 10 – – – Unit mA mA mA Measuring Condition Iq Iq,10 Iq,250 IQ = 0 mA VI = 6 V IQ = 10 mA VI = 6 V IQ = 250 mA VI = 6 V VC,off VI,cl IC,max VDR025 VDR06 VDR07 7.7 21 0.7 – – – 8.2 23 1.2 0.8 1.2 1.4 8.7 25 1.6 1.1 1.5 2.0 V V A V V V – II = 250 mA VC = 5 V IC = 0.25 A IC = 0.6 A IC = 0.7 A VQ VQ IQ,max VDR025 VDR06 VDR08 VDR ∆VQLO 3.7 3.2 0.8 – – – – – 3.8 3.3 1.2 0.2 0.4 1.0 1.1 20 3.9 3.4 1.6 0.4 0.7 2.0 1.3 40 V V A V V V V mV 0 < IQ < 250 mA, TLE 4307 DV38 0 < IQ < 250 mA, TLE 4307 DV33 – IQ = 0,25 A1) IQ = 0.6 A1) IQ = 0.8 A1) IQ = 0.25 A1) 200 mA < IQ < 600 mA Data Sheet Rev. 1.1 7 2000-10-11 TLE 4307 Electrical Characteristics (cont’d) VI = 12 V; 40 °C < Tj < 150 °C All voltages with respect to ground; positive current defined flowing into the pin; unless otherwise specified. Parameter Line regulation Power Supply Ripple rejection Output Capacitor Slewrate Input Input Resistance 1) Symbol ∆VQLI – Limit Values min. typ. – – – max. 20 – – Unit mV dB µF Measuring Condition 5 V < VC < 8.7 V IQ = 10 mA PSRR CQ – 40 22 fr = 100 Hz; Vr = 0.5 VSS ESR < 1 Ω RSL 60 120 200 kΩ VSL = 0.2 V Drop Voltage measured when the output voltage has dropped 100 mV from the nominal value. TLE 4307 VIN = 12 V RV 10 Ω LV 1 mH I1 CS SL 4 Power Charge Pump Very 5Q Low-Drop Regulator VOUT = 3.8 V 100 pF 2 C 3 GND CC 470 µF CQ 22 µF AES02795 Figure 4 Measurement Circuit Data Sheet Rev. 1.1 8 2000-10-11 TLE 4307 Package Outlines P-TO252-5-1 (D-PAK) (Plastic Transistor Single Outline Package) 2.3 +0.05 -0.10 B A 1 ±0.1 0...0.15 0.9 +0.08 -0.04 6.5 +0.15 -0.10 1 ±0.1 5.4 ±0.1 9.9 ±0.5 6.22 -0.2 0.8 ±0.15 (4.17) 0.15 max per side 0.51 min 5x0.6 ±0.1 1.14 0.5 +0.08 -0.04 0.1 4.56 0.25 M AB GPT09161 All metal surfaces tin plated, except area of cut. Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book “Package Information”. SMD = Surface Mounted Device Data Sheet Rev. 1.1 9 Dimensions in mm 2000-10-11 TLE 4307 Edition 2000-10-11 Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81541 München, Germany © Infineon Technologies AG 2000. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of noninfringement, regarding circuits, descriptions and charts stated herein. Infineon Technologies is an approved CECC manufacturer. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide (see address list). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Data Sheet Rev. 1.1 10 2000-10-11