TLE6254-3G_07

D ata Sheet, Rev. 2.1, Aug. 2007 TLE6254-3G Fault Tolerant Low Speed CANTransceiver Automotive Power Edition 2007-08-09 Published by Infineon Technologies AG 81726 Munich, Germany © 2005 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Fault Tolerant Low Speed CAN-Transceiver TLE6254-3G Features • • • • • • • • • • • • • • • Data transmission rate up to 125 kBaud Low current consumption in stand-by and sleep operation mode, including BUS wake-up Implemented receive-only mode Optimized EMC behavior Wake-up input pin, dual edge sensitive Battery fail flag Extended bus failure management to guarantee safe operation during all bus line failure events Support of failure conditions Fully wake-up capability during all bus line failures conditions Supports one-wire transmission mode with ground offset voltages up to 1.5 V Prevention from bus occupation in case of CAN controller failure Thermal protection Bus line error protection against transients in automotive environment Green Product (RoHS compliant) AEC Qualified Description The CAN-Transceiver TLE6254-3G works as the interface between the CAN protocol controller and the physical CAN bus-lines. It is optimized for low-speed data transmission (up to 125 kBaud) in automotive and industrial applications. While no data is transferred, the power consumption can be minimized by multiple low power modes. In normal operation mode a differential signal is transmitted/received. When bus wiring failures are detected the device automatically switches in a dedicated single-wire mode to maintain communication. Type TLE6254-3G Data Sheet 3 Package PG-DSO-14 Rev. 2.1, 2007-08-09 TLE6254-3G T L E6254 -3G IN H T xD R xD N ER R N ST B EN T WK 1 2 3 4 5 6 7 14 13 12 11 10 9 8 AEP03323N.VSD VS GN D C AN L C AN H VCC RTL RTH Figure 1 Table 1 Pin No. 1 2 3 4 5 6 7 Pin Configuration PG-DSO-14 (top view) Pin Definitions and Functions Symbol INH TxD RxD NERR NSTB ENT WK Function Inhibit output; for controlling an external voltage regulator Transmit data input; integrated pull-up, LOW: bus becomes dominant, HIGH: bus becomes recessive Receive data output; integrated pull-up, LOW: bus is dominant, HIGH: bus is recessive Error flag output; integrated pull-up, LOW: bus error (in normal operation mode), further functions see Table 2 Not stand-by input; digital control input to select operation modes, see Figure 4 Enable transfer input; digital control input to select operation modes, see Figure 4 Wake-Up input; if level of VWAKE changes the device indicates a wake-up from low power mode by switching the RxD outputs LOW and switching the INH output HIGH (in sleep mode), see Table 2 Data Sheet 4 Rev. 2.1, 2007-08-09 TLE6254-3G Table 1 Pin No. 8 Pin Definitions and Functions (cont’d) Symbol RTH Function Termination resistor output; connected to CANH bus-line via termination resistor (500 Ω < RRTH < 16 kΩ), controlled by internal failure management Termination resistor output; connected to CANL bus-line via termination resistor (500 Ω < RRTL < 16 kΩ), controlled by internal failure and mode management Supply voltage input; +5 V, block to GND directly at the IC with ceramic capacitor CAN bus line H; HIGH: dominant state CAN bus line L; LOW: dominant state Ground Battery voltage supply input; block to GND directly at the IC with ceramic capacitor 9 RTL 10 11 12 13 14 VCC CANH CANL GND VS Data Sheet 5 Rev. 2.1, 2007-08-09 TLE6254-3G Functional Block Diagram VCC 10 VS 14 1 RTL CANH CANL RTH 9 11 12 8 Output Stage Mode Control (normal, stand-by, sleep) Driver TempProtection 2 Time Out 7 6 5 INH WK ENT NSTB TxD VCC Bus Failure Wake-Up 7.2 Fail Flag 1.8 VBat 4 NERR Failure Management VCC Multiplexer -2.8 Filter 3.2 3 RxD 7.2 GND 13 Receiver AEA03314.VSD Figure 2 Block Diagram Data Sheet 6 Rev. 2.1, 2007-08-09 TLE6254-3G Circuit Description The CAN transceiver TLE6254-3G works as the interface between the CAN protocol controller and the physical CAN bus-lines. Figure 3 shows the principle configuration of a CAN network. The TLE6254-3G is optimized for low-speed data transmission (up to 125 kBaud) in automotive and industrial applications. In normal operation mode a differential signal is transmitted/received. When bus wiring failures are detected the device automatically switches in a dedicated single-wire mode to maintain communication. While no data is transferred, the power consumption can be minimized by multiple low power operation modes. Further a receive-only mode is implemented. To reduce radiated electromagnetic emission (EME) the dynamic slopes of the CANL and CANH signals are both limited and symmetric. This allows the use of an unshielded twisted or parallel pair of wires for the bus. During single-wire transmission (one of the bus lines is affected by a bus line failure) the EME performance of the system is degraded from the differential mode. In case the transmission data input TxD is permanently dominant, both, the CANH and CANL transmitting stage are disabled after a certain delay time. This is necessary to prevent the bus from being blocked by a defective protocol unit or short to GND at the TxD input. Local Area 1 Local Area 2 Controller 1 Controller 2 RxD 1 TxD 1 RxD 2 TxD 2 Transceiver 1 Transceiver 2 Bus Line AES02410 Figure 3 CAN Network Example Data Sheet 7 Rev. 2.1, 2007-08-09 TLE6254-3G Power Down Start Up Power Up Normal Mode NSTB 1 ENT 1 INH High NSTB ENT 1 1 NSTB ENT 0 ENT 1 ENT or 0 0 Low VCC RxD-Only 0 NSTB 1 NSTB ENT 0 INH High NSTB 0 or Low 1 0 VCC NSTB VBat Stand-By NSTB ENT 0 INH High NSTB ENT 0 1 ENT 1 0 ENT t < th(min) Wake-Up via CAN-Bus or WK-Input; t > tWU(min) or t > tWK(min) Go to Sleep Mode NSTB 0 ENT 1 INH High ENT = 1 t > th(min) 0 Sleep Mode NSTB ENT 0 INH Float. AEA03317.VSD Figure 4 State Diagram Data Sheet 8 Rev. 2.1, 2007-08-09 TLE6254-3G Operation Modes, Wake-Up In addition to the normal operation mode, the TLE6254-3G offers a receive-only mode as well as two low power operation modes to save power during periods that do not require communication on the CAN bus: sleep mode, VBAT stand-by mode (see Table 2 and Figure 4). Via the control input pins NSTB and ENT the operation modes are selected by the microcontroller. In the low power modes neither receiving nor transmitting of messages is possible. In sleep operation mode the lowest power consumption is achieved. In order to minimize the overall current consumption of the ECU (electronic control unit) the external voltage regulator (5 V supply) is deactivated by the INH output in this mode, when connected. For that purpose the INH output is switched to high impedance. In parallel the CANL line is pulled-up to the battery supply voltage via the RTL output and the pull-up paths at the input pins TxD and RxD are disabled from the internal supply. To enter the sleep operation mode the transition mode “Go-to-Sleep” has to be selected (Figure 4) for a minimum time th(min). After the minimum hold time th(min) the sleep mode can be actively selected. Otherwise the TLE6254-3G will automatically fall in sleep mode because of the not powered microcontroller. On a wake-up request either by bus line activities or via the WAKE input, the transceiver is automatically set in VBAT stand-by mode. Now the voltage regulator (5 V supply) is enabled by the INH output. The WAKE input reacts to both, transition from high to low voltage level as well as the other way round. To avoid faulty wake-ups due to transients on the bus lines or the WAKE input circuitry respectively, a certain filter time is implemented. As soon as VCC is provided, the wake-up request is monitored on both, the NERR and RxD outputs, by setting them low. Upon this the microcontroller can activate the normal operation mode by setting the control inputs NSTB and ENT high. The VBAT stand-by mode corresponds to the sleep mode, but a voltage regulator connected to the INH output will remain active. Wake-up requests via the WAKE pin or the bus lines are immediately reported to the microcontroller by setting RxD and NERR low. A power-on condition (VBAT pin is supplied) automatically switches the TLE6254-3G to VBAT stand-by mode. In the receive-only mode data on the CAN-bus are transferred to the RxD output, but both output stages, CANH as well as CANL are disabled. This means that data at the TxD input are not transmitted to the CAN bus. This mode is useful in combination to a dedicated network-management software that allows separate diagnosis for all nodes. A wake-up request in the receive-only mode is only reported at the RxD-output. The NERR output in this mode is used to indicate a battery fail condition. When entering the normal mode the VBAT-flag is reset and the NERR output becomes high again. This feature is useful e.g. when changing the ECU and therefore a presetting routine of the microcontroller has to be started. Data Sheet 9 Rev. 2.1, 2007-08-09 TLE6254-3G If either of the supply voltages drops below the specified limits, the transceiver is automatically switched to VBAT stand-by mode or power down mode respectively. Table 2 NSTB 0 0 0 1 ENT 0 0 1 0 Truth Table of the CAN Transceiver Mode mode1) INH NERR RxD RTL switched to VBAT switched to VBAT switched to VBAT active LOW HIGH = recessive switched VBAT power-on receive data; to VCC flag3) LOW = dominant receive data active LOW bus error flag HIGH = recessive switched receive data; to VCC LOW = dominant receive data VBAT stand-by VBAT sleep mode2) go to sleep command Receive-only mode floating becomes floating active LOW wake-up interrupt if VCC is present VBAT 1 1 normal mode VBAT 1) Wake-up interrupts are released when entering normal operation mode. 2) If go to sleep command was used before, ENT may turn LOW as VCC drops, without affecting internal functions. 3) VBAT power-on flag will be reseted when entering normal operation mode. Bus Failure Management The TLE6254-3G detects the bus failures as described in Table 3, and automatically switches to a dedicated CANH or CANL single wire mode to maintain data transmission if necessary. Therefore, the device is equipped with one differential receiver and 4 single ended receivers, two for each bus line. To avoid false triggering by external RF influences the single wire modes are only activated after a certain delay time. As soon as the bus failure disappears the transceiver switches back to differential mode after another time delay. Bus failures are indicated in the normal operation mode by setting the NERR output low. The differential receiver threshold is typ. -3.1 V. This ensures correct reception in the normal operation mode as well as in the failure cases 1, 2 and 4 with a noise margin as high as possible. For these failures, further failure management is not necessary. Detection of the failure cases 1, 2, 3a and 4 is only possible when the bus is dominant. Nevertheless, they are reported on the NERR output until transmission of the next CAN word on the bus begins. Data Sheet 10 Rev. 2.1, 2007-08-09 TLE6254-3G When one of the bus failures 3, 5, 6, 6a and 7 is detected, the defective bus wire is disabled by switching off the affected bus termination and the respective output stage. A wake-up from sleep mode via the bus is possible either via a dominant CANH or CANL line. This ensures that a wake-up is possible even if one of the failures 1 to 7 occurs. Table 3 Failure # 1 2 3 3a 4 5 6 6a 7 CAN Bus-line Failures Failure Description CANL line interrupted CANH line interrupted CANL line shorted to VBAT CANL line shorted to VCC CANH line shorted to GND CANL line shorted to GND CANH line shorted to VBAT CANH line shorted to VCC CANL line shorted to CANH line A current limiting circuit protects the CAN transceiver output stages from damage by short-circuit to positive and negative battery voltages. The CANH and CANL pins are protected against electrical transients which may occur in the severe conditions of automotive environments. The transmitter output stages generate the majority of the power dissipation. Therefore they are disabled if the junction temperature exceeds the maximum value. This effectively reduces power dissipation, and hence will lead to a lower chip temperature, while other parts of the IC can remain operating. In temperature shut-down condition the TLE6254-3G is still able to receive CAN-bus messages. Data Sheet 11 Rev. 2.1, 2007-08-09 TLE6254-3G Application Hints Table 4 Pin Symbol INH NERR NSTB ENT WAKE Not Needed Pins Recommendation Leave open Leave open Connect to VCC Connect to VCC Connect to VBAT, connect to GND: increases current consumption by approx. 5 µA Data Sheet 12 Rev. 2.1, 2007-08-09 TLE6254-3G Table 5 Parameter Absolute Maximum Ratings Symbol Limit Values Min. Max. 40 6 V V V V V V – – – – 1) Unit Notes VS VCC Input voltage at TxD, RxD, NERR, NSTB VIN Logic supply voltage VCC and ENT Input voltage at CANH and CANL Transient voltage at CANH and CANL Input voltage at WAKE Input voltage at INH Input voltage at RTH and RTL Junction temperature Storage temperature Electrostatic discharge voltage at pin CANH, CANL, RTH, RTL, VBAT Electrostatic discharge voltage at any other pin 1) See ISO 7637 Input voltage at VBAT -0.3 -0.3 -0.3 -40 -150 -40 -0.3 -0.3 -40 -55 -4 -2 VCC + 0.3 40 100 40 0.3 VBUS VBUS VWK VINH VRTH/L Tj Tstg Vesd Vesd – – – – – 2) VBAT + V 40 160 155 4 2 V °C °C kV kV 2) 2) Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ resistor. Note: Stresses above those listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Data Sheet 13 Rev. 2.1, 2007-08-09 TLE6254-3G Table 6 Parameter Operating Range Symbol Limit Values Min. Max. 5.25 27 16 150 120 200 V V kΩ °C K/W °C – – – – – 10 °C hyst. – 4.75 5.7 0.5 -40 – 160 Unit Notes Logic input voltage Battery input voltage Termination resistances at RTL and RTH Junction temperature Thermal Resistance Junction ambient Thermal Shutdown Junction temperature Wake Input Voltage Wake input voltage VCC VS RRTL/H Tj Rthja TjSH VWK -0.3 27 V Note: In the operating range, the functions given in the circuit description are fulfilled. Data Sheet 14 Rev. 2.1, 2007-08-09 TLE6254-3G Table 7 Static Characteristics 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Supplies VCC, VS Supply current Symbol Min. Limit Values Typ. 3.5 6.5 3.5 25 30 55 Max. 10.0 10 10.0 55 50 85 mA mA mA µA µA µA recessive; TxD = VCC dominant; TxD = 0 V; no load – Unit Notes ICC – – Supply current (Receive-only mode) Supply current (VBAT stand-by) Supply current (VBAT stand-by) Supply current (sleep operation mode) Supply current (sleep operation mode) Battery voltage for setting power-on flag HIGH level output voltage (pin NERR) HIGH level output voltage (pin RxD) ICC ICC IS ICC + IS – – – VCC = 5 V; VS = 12 V VCC = 5 V; VS = 12 V Tj = 25 °C VCC = 0 V; VS = 12 V VCC = 0 V; VS = 12 V Tj = 25 °C IS IS – – 50 50 70 65 µA µA VS - 1 3.5 V Receiver Output RxD and Error Detection Output NERR VOH VOH VCC 0.9 – – – VCC VCC 0.9 V V V I0 = -100 µA I0 = -250 µA I0 = 1.25 mA VCC 0.9 0 LOW level output voltage VOL Data Sheet 15 Rev. 2.1, 2007-08-09 TLE6254-3G Table 7 Static Characteristics (cont’d) 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Symbol Min. HIGH level input voltage VIH LOW level input voltage HIGH level input current (pins NSTB and ENT) LOW level input current (pins NSTB and ENT) HIGH level input current (pin TxD) LOW level input current (pin TxD) 0.7 × Limit Values Typ. – – 20 6 -30 -300 – Max. Unit Notes Transmission Input TxD, not Stand-By NSTB and Enable Transfer ENT VCC + V 0.3 0.3 × V µA µA µA µA V – – VCC VIL IIH IIL IIH IIL -0.3 – 0.7 -150 -600 2.75 VCC 80 – -5 -40 4.5 Vi = 4 V Vi = 1 V Vi = 4 V Vi = 1 V – Forced battery voltage VCC stand-by mode (fail safe) Wake-up Input WAKE Input current Wake-up threshold voltage Inhibit Output INH HIGH level voltage drop ∆VH = VS - VINH Leakage current ∆VH IIL VWK(min) -3 2.2 -2 3.0 -1 3.9 µA V VWK = 0 V VNSTB = 0 V – -5.0 0.1 – 0.8 5.0 V µA IINH = -0.18 mA sleep operation mode; VINH = 0 V IINH,lk Data Sheet 16 Rev. 2.1, 2007-08-09 TLE6254-3G Table 7 Static Characteristics (cont’d) 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Bus Lines CANL, CANH Differential receiver recessive-to-dominant threshold voltage Differential receiver dominant-to-recessive threshold voltage CANH recessive output voltage CANL recessive output voltage CANH dominant output voltage CANL dominant output voltage CANH output current Symbol Min. Limit Values Typ. -3.1 Max. -2.6 V Unit Notes VdRxD(rd) -3.6 VCC = 5.0 V VdRxD(dr) -3.6 -3.1 -2.6 V VCC = 5.0 V VCANH,r VCANL,r VCANH,d 0.10 0.15 – 0.30 – V V V TxD = VCC; RRTH < 4 kΩ TxD = VCC; RRTL < 4 kΩ TxD = 0 V; VCC = 5V; RL = 100Ω TxD = 0 V; VCC = 5V; RL = 100Ω VCC 0.2 VCC 1.4 VCC 1.0 1.0 VCC VCANL,d – 1.4 V ICANH -110 -5 -80 0 -50 5 mA µA VCANH = 0 V; TxD = 0 V sleep operation mode; VCANH = 12 V CANL output current ICANL 50 -5 80 0 110 5 mA µA VCANL = 5 V; TxD = 0 V sleep operation mode; VCANL = 0 V; VS = 12 V Data Sheet 17 Rev. 2.1, 2007-08-09 TLE6254-3G Table 7 Static Characteristics (cont’d) 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Symbol Min. Voltage detection Vdet(th) threshold for short-circuit to battery voltage on CANH and CANL CANH wake-up voltage threshold CANL wake-up voltage threshold CANH single-ended receiver threshold CANL single-ended receiver threshold Difference of wake-up threshold CANL leakage current 6.5 Limit Values Typ. 7.3 Max. 8.0 V – Unit Notes VCANH,wu 1.1 VCANL,wu 2.5 VCANH VCANL Vdiff,wu ICANL,lk 1.5 2.8 0.8 -5 2.2 3.1 1.8 3.1 2.5 3.9 2.3 3.5 V V V V V – – failure cases 3, 5 and 7; VCC = 5 V failure case 6 and 6a; VCC = 5 V 0 5 µA CANH leakage current ICANH,lk -5 0 5 µA VCC = 0 V; VS = 0 V; VCANL = 12 V; Tj < 85 °C VCC = 0 V; VS = 0 V; VCANH = 5 V; Tj < 85 °C Data Sheet 18 Rev. 2.1, 2007-08-09 TLE6254-3G Table 7 Static Characteristics (cont’d) 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Symbol Min. Termination Outputs RTL, RTH RTL to VCC switch-on resistance Limit Values Typ. 20 15 Max. 95 30 Ω kΩ Unit Notes RRTL – 8 Io = -10 mA VBAT stand-by or sleep operation mode RTL to BAT switch series RoRTL resistance RTH to ground switch-on RRTH resistance RTH output voltage RTH pull-down current RTL pull-up current RTH leakage current – – 40 -120 -5 40 0.7 75 -75 0 95 1.0 120 -40 5 Ω V µA µA µA Io = 10 mA Io = 1 mA; low power mode failure cases 6 and 6a failure cases 3, 5 and 7 VoRTH IRTH,pd IRTL,pu IRTH,lk RTL leakage current IRTL,lk -10 0 10 µA VCC = 0 V; VS = 0 V; VRTH = 5 V; Tj < 85 °C VCC = 0 V; VS = 0 V; VRTL = 12 V; Tj < 85 °C Data Sheet 19 Rev. 2.1, 2007-08-09 TLE6254-3G Table 8 Dynamic Characteristics 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter CANH and CANL bus output transition time recessive-to-dominant CANH and CANL bus output transition time dominant-to-recessive Minimum dominant time for wake-up via CANL or CANH Symbol Limit Values Min. Typ. 1.2 Max. 2.4 µs 10% to 90%; C1 = 10 nF; C2 = 0; R1 = 100 Ω 10% to 90%; C1 = 1 nF; C2 = 0; R1 = 100 Ω stand-by modes; VS = 12 V Low power modes; 0.6 Unit Notes trd tdr 0.3 0.6 1.3 µs twu(min) 8 25 40 µs Minimum wake-up time on tWK(min) pin WAKE Failure cases 3, 6 detection time Failure case 6a detection time Failure cases 5, 7 detection time Failure cases 5, 6, 6a, 7 recovery time Failure cases 3 recovery time Failure cases 5, 7 detection time Failure cases 5, 7 recovery time Failure cases 6, 6a detection time Failure cases 6, 6a recovery time 8 20 2 1.0 20 250 0.4 0.4 0.8 0.4 25 40 4 2.0 40 500 1.0 1.0 4.0 1.0 50 80 8 4.0 80 750 2.4 2.4 8.0 2.4 µs µs ms ms µs µs ms ms ms ms VS = 12 V Normal Mode Normal Mode Normal Mode Normal Mode Normal Mode stand-by modes; VS = 12 V stand-by modes; VS = 12 V stand-by modes; VS = 12 V stand-by modes; VS = 12 V tfail Data Sheet 20 Rev. 2.1, 2007-08-09 TLE6254-3G Table 8 Dynamic Characteristics (cont’d) 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Propagation delay TxD-to-RxD LOW (recessive to dominant) Symbol Limit Values Min. Typ. 1.3 Max. 2.4 µs – Unit Notes tPD(L) C1 = 100 pF; C2 = 0; R1 = 100 Ω; no failures and bus failure cases 1, 2, 3a, 4 – 1.5 2.4 µs C1 = C2 = 3.3 nF; R1 = 100 Ω; no bus failure and failure cases 1, 2, 3a, 4 – 1.6 2.5 µs C1 = 100 pF; C2 = 0; R1 = 100 Ω; bus failure cases 3, 5, 6, 6a – 1.8 2.6 µs C1 = C2 = 3.3 nF; R1 =100 Ω; bus failure cases 3, 5, 6, 6a Propagation delay TxD-to-RxD HIGH (dominant to recessive) tPD(H) – 1.2 2.4 µs C1 = 100 pF; C2 = 0; R1 =100 Ω; no failures and bus failure cases 1, 2, 3a, 4 – 2.5 3.5 µs C1 = C2 = 3.3 nF; R1 = 100 Ω; no bus failure and failure cases 1, 2, 3a, 4 Data Sheet 21 Rev. 2.1, 2007-08-09 TLE6254-3G Table 8 Dynamic Characteristics (cont’d) 4.75 V ≤ VCC ≤ 5.25 V; 6 V ≤ VS ≤ 27 V; normal operation mode; -40 ≤ Tj ≤ +125 °C (unless otherwise specified). All voltages are defined with respect to ground. Positive current flowing into the IC. Parameter Propagation delay TxD-to-RxD HIGH (dominant to recessive) Symbol Limit Values Min. Typ. 1.0 Max. 2.1 µs – Unit Notes tPD(H) C1 = 100 pF; C2 = 0; R1 = 100 Ω; bus failure cases 3, 5, 6, 6a – 1.5 2.6 µs C1 = C2 = 3.3 nF; R1 = 100 Ω; bus failure cases 3, 5, 6, 6a Minimum hold time to go sleep command th(min) 15 – 30 4 60 – µs – – normal operating mode Edge-count difference ne (falling edge) between CANH and CANL for failure cases 1, 2, 3a, 4 detection NERR becomes LOW Edge-count difference (rising edge) between CANH and CANL for failure cases 1, 2, 3a, 4 recovery TxD permanent dominant disable time – 2 – – normal operating mode tTxD 1.3 2.0 3.5 ms – Data Sheet 22 Rev. 2.1, 2007-08-09 TLE6254-3G Test and Application +5V 7 6 5 4 3 2 TxD 1 INH 20 pF WAKE ENT NSTB NERR RxD TLE6254-3G TLE 6254-3G RTH RTL 8 9 CAN Transceiver V CC CANH CANL GND V BAT 10 11 12 13 14 + 12 V R1 R1 C1 C2 C1 R 1 = 100 Ω C 1,2 = 10 nF R1 C K = 1 nF CAN Bus Substitute 1 R1 CK Schaffner Generator CK CAN Bus Substitute 2 AES02423 Figure 5 Test Circuits For isolated testing the CAN Bus Substitute 1 is connected to the CAN Transceiver (see Figure 5). The capacitors C1-2 simulate the cable. Allowed minimum values of the termination resistors RRTH and RRTL are 500 Ω. Electromagnetic interference on the bus lines is simulated by switching to CAN Bus Substitute 2. The waves of the applied transients will be in accordance with ISO 7637 part 1, test 1, test pulses 1, 2, 3a and 3b. Data Sheet 23 Rev. 2.1, 2007-08-09 TLE6254-3G V Bat C AN Bus C hoke 1 ) 11 12 T L E6254-3 G C AN H C AN L RTH RTL 3 2 6 5 4 10 100 nF e.g. C 50C , C 164C GN D µP w ith On-C hip C AN -m odule RxD TxD EN T N ST B N ER R RRT H 8 9 R RT L 14 100 nF 10 k Ω 7 1 VS WK IN H VCC GN D IN H E.g . T LE 4263 T LE 4299 T LE 4271 T LE 4276 GN D VCC VS + 22 µF 100 nF + 22 µF 1) Optional , ac cording to c ar m anufac turers requirem ents AEA 03307 .VSD Figure 6 Application Example Data Sheet 24 Rev. 2.1, 2007-08-09 TLE6254-3G Package Outlines 0.35 x 45˚ 1.75 MAX. 0.175 ±0.07 (1.47) C 4 -0.2 1.27 0.41+0.10 2) -0.06 14 B 0.1 0.2 M A B 14x 8 6±0.2 0.64 ±0.25 0.2 M C 1 7 1) 8.75 -0.2 A Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area GPS01230 Figure 7 PG-DSO-14 (Plastic Dual Small Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet 25 Dimensions in mm Rev. 2.1, 2007-08-09 8˚MAX. 1) 0.19 +0.06 TLE6254-3G Revision History Version Rev. 2.1 Date Changes 2007-08-08 RoHS-compliant version of the TLE6254-3G • All pages : Infineon logo updated • Page 3: added “AEC qualified” and “RoHS” logo, “Green Product (RoHS compliant)” and “AEC qualified” statement added to feature list, package name changed to RoHS compliant versions, package picture updated, ordering code removed. • Page 25: Update package drawing to GPS01230 Package name changed to RoHS compliant versions, “Green Product” description added • added Revision History • updated Legal Disclaimer Data Sheet 26 Rev. 2.1, 2007-08-09