V23806-S84-Z4

V23806-S84-Z3 3.3 V V23806-S84-Z4 5V Testboard for ATM, ESCON, Fibre Channel and Gigabit Ethernet 1x9 Transceivers FEATURES • Allows for separate powering of receiver and transmitter section • Power supply lines filtered externally to module under test • Signal Detect level displayed by LED • Power supply can be interrupted separately for receiver and transmitter • External Data and Signal Detect interfaces are made through high performance SMA connectors • Receiver data outputs are DC coupled. Output voltage can be directly measured at SMA connectors Figure 1. Application board (Top view) DESCRIPTION This testboard is a functional test fixture intended for use with the 1x9 pin row single mode 155MBd or 622MBd ATM transceiver, ESCON, Fibre Channel and Gigabit Ethernet transceivers. It provides a test medium for characterizing the performance of these transceivers. SMA-connector (female) Infineon RxSD Fiber Optics V23806-S84-Z3/Z4 APPLICATION BOARD ATM/ESCON/FC/GBd Ethernet 155-1250 MBd 3.3 V/5 V - Version Power supply connector (female) LED (red) 3-Pin jumper, to measure and to interrupt receiver/ transmitter power supply RxVCC TxVCC GND RxD RxD TxD TxD Fiber Optics NOVEMBER 1999 Connectors/Test Pins Label SD(1) RxD RxDn TxD TxDn VCC VEE Notes 1. Some transceiver versions have TTL -SD-output. For this type no load is required. Type SMA SMA SMA SMA SMA Name Signal Detect Output Receiver Data Output Receiver Data Not Output Transmitter Data Input Transmitter Data Not Input Power Supply Ground Level PECL Output PECL Output PECL Output PECL Input PECL Input Description To measure use 50 Ω load to VEE Load is 50Ω to VEE (GND), DC coupled or AC coupled, depending on board assembly (see page 4) Load is 50Ω to VEE (GND), AC coupled (see page 4) In accordance with recommended operating conditions of transceiver (3.3V / 5V) Indicators/Switches Label SD JMP Type LED Jumper Name Signal Detect Indicator Signal Detect Level active high Description LED off: SD off LED on: SD on connects signal detect to either SMA connector or OPAMP (LED) Fiber Optics 2 V23806-S84-Z3/Z4, Testboard for ATM, ESCON, Fibre Channel, GBE 1x9 Trx Figure 2. Schematic of Application board (initial assembly)* Values in brackets: 3.3 V board FO-Transceiver Top view RxVCC RxVCC 1 100 nF RxD 50 Ω stripline C2 R4 300Ω (150Ω) 100 nF RxD 50 Ω stripline C1 R3 300Ω (150Ω) RxVCC 82Ω** (127Ω) SD 75Ω (33Ω) ** RxVCC 82Ω** (127Ω) 127Ω** (82Ω) TxVCC R9 68Ω (82Ω) 191Ω 50 Ω stripline (127Ω) 100 nF TxD R7 Jumper SD C11 R10 68Ω (82Ω) 191Ω 50 Ω stripline (127Ω) 100 nF TxD C12 Rx Tx TxVCC TxVCC TxVCC R8 LM 319 + 150Ω 1.5 K 4.3 K (2.2 K) ((1.0 K))** * Suitable for DC/DC Transceiver only. For AC/AC and AC/DC please see page 4. ** Remove when TTL-SD; change resistor to value in double brackets. Fiber Optics 3 V23806-S84-Z3/Z4, Testboard for ATM, ESCON, Fibre Channel, GBE 1x9 Trx Variation of Testboard for different type of electrical transceiver interfaces. Values in brackets refer to 3.3 V operation. Part numbers of passive components refer to Fig. 9 to 12 (Assembly plan). Figure 3. DC-type receiver (V23826-XXX-C(3)6X, V23806A84-XXX, V23809-E11-C10) - AC-coupled to test (initial assembly) Figure 7. DC-transmitter (V23826-XXX-C(3)6X, V23806-A84XXX, V23809-E11-C10) - DC-coupled to test(1) R9/10 = 68 (82) Ohm R7/8 = 191 (127) Ohm C11/12 = shorted VCC R9/10 50 Ohm Stripline Tx-In R7/8 Puls Gen.* *) PECL Driver R3/4 = 300 (150) Ohm C1/2 = 100 nF in position of R1/2 C1/2 Rx-Out R3/4 50 Ohm Stripline 50 Ohm Figure 8. AC-type transmitter V23826-XXX-C(3)13, V23826XXX-C(3)53(1) R9/10 = removed R7/8 = removed C11/12 = shorted Figure 4. DC type receiver (V23826-XXX-C(3)6X, V23806A84-XXX, V23809-E11-C10) - DC-coupled to test system Output Voltage divided by 2.5 (1.66) 50 Ohm Stripline VCC R5/6 = 82 (127) Ohm R1/2 = 75 (33) Ohm Tx-In Puls Gen. R5/6 Rx-Out R1/2 50 Ohm Stripline 50 Ohm Assembly Plan Figure 5. AC-type receiver V23826-XXX-C(3)53 R3/4 = removed R5/6 = removed C1/2 = shorted Rx-Out 50 Ohm Stripline R/C2 Figure 9. Top side (Detail of Figure 11) Rx-Part Tx-Part PIN 1 R/C1 50 Ohm Figure 10. Bottom side (Detail of Figure 12) Figure 6. DC-type transmitter (V23826-XXX-C(3)6X, V23806A84-XXX, V23809-E11-C10) -AC-coupled to test (initial assembly)(1) R9/10 = 68 (82) Ohm R7/8 = 191 (127) Ohm C11/12 = close to SMAconnector (100 nF) VCC Tx-Part Rx-Part PIN 1 CVCC R10 R8 R9 R7 R3 R5 R6 CVCC 10 nF R4 10 nF R9/10 C11/12 50 Ohm Stripline R7/8 Puls Gen. Tx-In Note: 1. It is recommended to drive the transmitter with differential signals. Fiber Optics 4 V23806-S84-Z3/Z4, Testboard for ATM, ESCON, Fibre Channel, GBE 1x9 Trx Figure 11. Top side of application board PIN 1 Figure 12. Bottom side of application board PIN 1 C11/12 Published by Infineon Technologies AG Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your Infineon Technologies offices. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. © Infineon Technologies AG 1999 All Rights Reserved Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Infineon Technologies is an approved CECC manufacturer. Information For further information on technology, delivery terms and conditions and prices please contact the Infineon Technologies offices or our Infineon Technologies Representatives worldwide - see our webpage at www.infineon.com/fiberoptics Infineon Technologies AG • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany Infineon Technologies, Corp. • Fiber Optics • 19000 Homestead Road • Cupertino, CA 95014 USA Infineon Technologies K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku • Tokyo 141, Japan