FMCE-1528

Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp Features • Operating temperature -55° to +125°C attenuation to 70 dB at 500 kHz, typical • Nominal 28 V input, -0.5 to 50 V operation • Transient rating -0.5 to 80 V for 1 second • Up to 15 A throughput current over the full input voltage range of -0.5 to 50 V • Compliant to - MIL-STD-461C,CE03 - MIL-STD-461D, E and F CE102 - MIL-STD-461C CS01 - MIL-STD-461D, E and F CS101 Input vOltage and cuRRent Input (V) 28 Current (A) 15 • Compatible with MIL-STD-704 A-E 28 VDC power bus Description The FMCE-1528™ EMI filters are specifically designed to reduce the reflected input ripple current of Interpoint’s high frequency DC/DC converters. FMCE-1528 filters minimize electromagnetic interference (EMI) for the MFL, MOR, MTR, MHV, and MHF+ Series of converters. These filters are intended for use in 28 volt applications which must meet MIL-STD-461C CE03 and CS01 and/or MIL-STD-461D, E and F CE102 and CS101 levels of conducted emissions. One filter can be used with multiple converters up to the rated output current of the filter. Place the filter as close as possible to the converter for optimum performance. The baseplates of the filter and the converter should be connected with the shortest and widest possible conductors. tRansIents A transient of -0.5 to +80 volts (0.5 ohm source impedance) will not damage the filter but will be passed on to the converter: Input RIpple and eMI OpeRatIOn OveR teMpeRatuRe Switching DC/DC converters naturally generate two noise components on the power input line: differential noise and common mode noise. Input ripple current refers to both of these components. Differential noise occurs between the positive input and input common. Most Interpoint converters have an input filter that reduces differential noise which is sufficient for many applications. Common mode noise occurs across stray capacitances between the converter’s power train components and the baseplate (bottom of the package) of the converter. Where low noise currents are required to meet MIL-STD-461, a power line filter is needed. The FMCE-1528 EMI power line filters reduce the common mode and differential noise generated by the converters. FMCE-1528 filters reduce input ripple current by as much as 70 dB at 500 kHz and 1 MHz when used in conjunction with Interpoint’s DC/DC converters. The FMCE-1528 Series filters are rated for full power operation from -55°C to +125°C case temperature. Current is derated linearly to 80% at +135°C case temperature. InseRtIOn lOss packagIng The maximum dc insertion loss at full load and nominal input voltage represents a power loss of less than 4%. FMCE-1528 filters are sealed in metal hermetic side-leaded packages. See cases U, V, W, Y, and Z. Crane Aerospace & Electronics Electronics Group (Interpoint Brand) PO Box 97005 • Redmond WA 98073-9705 425.882.3100 • power@crane-eg.com www.interpoint.com Page 1 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp Operating COnditiOns and CharaCteristiCs input Voltage range • Continuous -0.5 to 50 VDC • Transient -0.5 to 80 V for 1 second meChaniCal and envirOnmental size (maximum) • Case U 3.005 x 1.505 x 0.400 inches (76.33 x 38.23 x 10.16 mm) The image on page one shows Case U (flanged, short leads) • Also available: ‣ Flanged: leads bent down (case V) ‣ Tabbed: leads bent up (case W) ‣ Tabbed: short leads (case Y) ‣ Tabbed: leads bent down (case Z) ‣ See cases U, V, W, Y, and Z for dimensions and options Weight (maximum) • 86 grams all cases (U, V, W, Y, and Z) screening lead soldering temperature (10 sec per lead) • 300°C storage temperature range (case) • -65°C to +150°C case operating temperature (tc) • -55°C to +125°C full power • -55°C to +135°C absolute electrostatic Discharge (esD) sensitivity per Mil-prF-38534 • Classification 3B, 8000 V isolation (tc = 25°c) • 100 megohm minimum at 500 VDC • Any pin to case Derating input/output current • Linearly from 100% at 125°C to 80% at 135° C The FMCE-1528 EMI Input filter offers Standard, /ES or 883, Class H, QML screening. See Screening Tables 1 and 2 for more information. EMI FILTER +Vin Case Output Input Common Common +Vout DC/DC CONVERTER +Vin +Vout RL Case Output Input Common Common Chassis ground Multiple units allowed up to rated output current of filter RL The case ground connection between the filter and the converter should be as low an impedance as possible to minimize EMI. Direct contact of baseplate to chassis ground provides the lowest impedance. Figure 1: ConneCtion Diagram L1 Positive Input R1 Positive Output T1 T2 R2 Input Common Output Common FIguRe 2: scheMatIc FMce-1528 www.interpoint.com Page 2 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp pin out pin out 1, 2, 3 4, 5, 6 10, 11, 12 Bottom of case 7, 8, 9 pin Positive Input Designation Input Common Output Common Positive Output Case Ground Notes 1. All pins must be connected. 2. The baseplate is the only case ground connection and should directly contact chassis ground. Angled corner and cover marking indicate pin one for cases U and V. Cover marking indicates pin one for cases W, Y and Z. 1 2 3 4 5 6 TOP VIEW U Case Outline shown is case U, pin out is the same for all cases. See cases U, V, W, Y, and Z for dimensions. 12 11 10 9 8 7 FIguRe 3: pIn Out www.interpoint.com Page 3 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp MoDel nuMBering key Base Model FMCE 15 28 V* / 883 DsCC Drawing (5915) 10018-01HTC 10018-01HUC 10018-01HXC 10018-01HYC 10018-01HZC Dscc nuMBers FmCe-1528 similar Part FMCE-1528-W/883 FMCE-1528-V/883 FMCE-1528/883 FMCE-1528-Y/883 FMCE-1528-Z/883 Output Current Input Voltage Case Option (Standard case “U” has no designator in this position) Screening (Standard screening has no designator in this position.) *Case/Lead Option: See cases U, V, W, Y, and Z for drawings and dimensions. For exact specifications for a DSCC product, refer to the DSCC drawing. DSCC drawings can be downloaded from: http://www.dscc.dla.mil/programs/smcr case options: Dscc cross referenced to interpoint DSCC Case Option T U X Y Z Interpoint Case Option W V (standard case, no option required) Y Z on the lines below, enter one seleCtion From unDer eaCh Category to Determine the moDel number. category FMce-1528 Base MoDel anD input Voltage MoDel selection – _______ case/leaD option 1 (stanDarD case u leave blank) / ______ screening 2 (stanDarD leave blank) es 883 (class H, QMl) selection “FMce-1528” is the only available selection V W y Z Notes: 1. Case U is the standard, side-leaded, flanged case. Leave the option blank for case U. Refer to the case drawings on pages 8 - 12 for other case options. 2. Leave blank for standard screening. Use “ES” for “ES” screening and “883” for Class H screening. See screening Tables 1 and 2 for more information. www.interpoint.com Page 4 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp Electrical Characteristics: -55° to +125°C TC, nominal Vin, unless otherwise specified. MODEL paRaMeteR Input vOltage nOIse ReJectIOn dc ResIstance (Rdc) at MaXIMuM cuRRent capacItance Output vOltage 3 Output cuRRent pOWeR dIssIpatIOn at MaXIMuM cuRRent 1 cOndItIOns tRansIent, 1 sec 1, 2 500 khz 1 Mhz tc = 25°c tc = 125°c 1 cOntInuOus MIN -0.5 -0.5 60 60 — — 50,000 FMCE-1528 TYP 28 — 70 70 — — 60,000 MAX 50 80 — — 0.06 0.07 70,000 unIts VDC V dB Ω pF VDC A W anY pIn tO case tc = 25°c steadY state steadY state vIn = -0.5 - 50 vdc tc = 125°c tc = 25°c VOUT = VIN - IIN (RDC) — — — — — — 15 13.5 15.75 Note 1. guaranteed by design, not tested. 2. 0.5 ohm source impedance 3. Typical applications result in Vout within 4% of Vin. www.interpoint.com Page 5 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp Typical Performance Curves: 25°C TC, nominal Vin, unless otherwise specified. 90 90 EMISSION LEVEL (dB µA) 70 60 50 40 30 20 10 0 .015 03 EMISSION LEVEL (dB µA) 80 CE MIL-STD-461 C POWER IN LIMITS LIM IT NARROWBAND 80 70 60 50 40 30 20 10 0 .015 CE MIL-STD-461 C POWER IN LIMITS 03 LIM IT NARROWBAND 0.1 FREQUENCY (MHz) 1 10 50 0.1 FREQUENCY (MHz) 1 10 50 Three paralleled and synchronized MFL2815D converters without filtering. FIguRe 4 CE03: Three paralleled and synchronized MFL2815D converters with an FMCE-1528. FIguRe 5 100 EMISSION LEVEL (dB µV) 90 80 70 60 50 40 30 20 10 .01 CE1 02 A Ca nd D CL imit s FREQUENCY (MHz) CE102: Three paralleled and synchronized MFL2815D converters with an FMCE-1528. 0.1 1 10 FIguRe 6 1.0 10 -10 -30 -50 -70 0.9 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.1 1.0 10 21 IMPEDANCE (OHMS) 0.75 ATTENUATION (dB) 0.8 FMCE-1528 Output Impedance (measured at the output with input pins shorted) FREQUENCY (kHz) 100 1 10 FREQUENCY (kHz) 100 1M FMCE-1528 Attenuation FIguRe 7 www.interpoint.com FIguRe 8 Page 6 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters – cases 28 Volt input – 15 aMp TOP VIEW CASE U* Flanged case, short-leaded *Does not require designator in Case Option position of model number. Angled corner indicates pin one. 1.505 (38.23) max. 1.380 (35.05) 1.250 (31.75) 1.050 (26.67) 0.850 (21.59) 0.650 (16.51) 0.450 (11.43) 0.250 (6.35) 0.120 (3.05) 0.000 0.000 1 2 3 4 5 6 12 11 10 9 8 7 0.23 (5.8) Pin Length 0.128 dia (3.25). 0.040 dia (1.02) Seam Seal 0.400 (10.16) max. 0.120 (3.05) 0.250 (6.35) 2.750 (69.85) 2.880 (73.15) 3.005 (76.33) max. Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compression glass seal Seal Hole: 0.100 ±0.002 (2.54 ±0.05) Case U, Rev F, 20100503 FIguRe 9: case u www.interpoint.com Page 7 of 13 FMCE-1528 Rev E - 20100615 0.050 (1.27) 0.000 0.220 (5.59 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters – cases 28 Volt input – 15 aMp TOP VIEW CASE V* Flanged case, down leaded *Designator "V" required in Case Option position of model number. Angled corner indicates pin one. 1.380 (35.05) 1.250 (31.75) 1.050 (26.67) 0.850 (21.59) 0.650 (16.51) 0.450 (11.43) 0.250 (6.35) 0.120 (3.05) 0.000 0.250 ±0.010 (6.35 ±0.3) 2.880 (73.15) 3.005 (76.33) max 0.400 (10.16) max ref: 0.250 ±0.050 (6.35 ±1.27) ref: 0.225 (5.72 0.000 0.120 (3.05) 2.750 (69.85) 0.220 (5.59) 0.050 (1.27) 0.000 1 2 3 4 5 6 12 11 10 9 8 7 Maximum dimensions: 3.005 x 1.505 (76.33 x 38.23 mm) 3.45 (87.6) Reference (lead center to lead center) 0.128 dia (3.25) 0.040 dia (1.02) Seam Seal Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glas seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) Case V, Rev F, 20100413 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. FIguRe 10: case v www.interpoint.com Page 8 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters – cases 28 Volt input – 15 aMp TOP VIEW CASE W* Tabbed case, up-leaded *Designator "W" required in Case Option position of model number. 0.250 (6.35) Typ. 1.750 (44.45) 1.625 (41.28) 1.375 (34.93) 1.175 (29.85 0.975 (24.77) 0.775 (19.69) 0.575 (14.61) 0.375 (9.53) 0.125 (3.18) 0.000 0.84 ±0.05 (21.3 ±1.3) 0.400 (10.16) max. 0.220 (5.59) 0.050 (1.27) 0.000 1 2 3 4 5 6 0.250 (6.35) Typ. 12 11 10 9 8 7 0.040 dia (1.02) 0.140 dia (3.56) Seam Seal 2.000 (50.80) 1.750 (44.45) 2.125 (53.98) 1.450 (36.83) 0.300 (7.62) 0.000 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glass seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) 0.375 (9.53) 0.84 ±0.05 (21.3 ±1.3) 0.400 (10.16) max. 0.220 (5.59) 0.000 Lead Detail 0.150 (3.81) 2.80 (71.1) Reference (lead center to lead center) Case W, Rev E, 20100413 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. FIguRe 11: case W www.interpoint.com Page 9 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters – cases 28 Volt input – 15 aMp TOP VIEW CASE Y* Tabbed case, straight-leaded *Designator “Y” required in Case Option position of model number. 0.250 (6.35) Typ. 1.750 (44.45) 1.625 (41.28) 1.375 (34.93) 1.175 (29.85 0.975 (24.77) 0.775 (19.69) 0.575 (14.61) 0.375 (9.53) 0.125 (3.18) 0.000 0.400 (10.16) max. 0.000 0.220 (5.59) 0.050 (1.27) 0.000 Pin Length 0.30 ±0.05 (7.6 ±1.3) 1 2 3 4 5 6 0.250 (6.35) Typ. 12 11 10 9 8 7 0.040 dia (1.02) 0.140 dia (3.56) Seam Seal 2.000 (50.80) 1.750 (44.45) 2.125 (53.98) 1.450 (36.83) 0.300 (7.62) 0.000 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glass seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) 0.375 (9.53) Lead Detail 0.400 (10.16) max. 0.220 (5.59) 0.30 ±0.05 (7.6 ±1.3) 3.10 (78.7) Reference Case Y, Rev E, 20100413 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. FIguRe 12: case Y www.interpoint.com Page 10 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters – cases 28 Volt input – 15 aMp TOP VIEW CASE Z* Tabbed case, down-leaded *Designator “Z” required in Case Option position of model number. 0.250 (6.35) Typ. 1.750 (44.45) 1.625 (41.28) 1.375 (34.93) 1.175 (29.85 0.975 (24.77) 0.775 (19.69) 0.575 (14.61) 0.375 (9.53) 0.125 (3.18) 0.000 0.400 (10.16) max. 0.220 (5.59) 0.050 (1.27) 0.000 0.36 ±0.05 (9.1±0.13) 1 2 3 4 5 6 0.250 (6.35) Typ. 12 11 10 9 8 7 0.040 dia (1.02) 0.140 dia (3.56) Seam Seal 2.000 (50.80) 1.750 (44.45) 2.125 (53.98) 1.450 (36.83) 0.300 (7.62) 0.000 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glass seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) 0.375 (9.53) 0.400 (10.16) max. 0.220 (5.59) 0.000 0.150 (3.81) Lead Detail 0.36 ±0.05 (9.1±0.13) 2.80 (71.1) Reference (lead center to lead center) Case Z, Rev E, 20100413 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. FIguRe 13: case z www.interpoint.com Page 11 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp STANDARD AND /ES (NON-QML) AND /883 (CLASS H, QML) PRODUCT ELEMENT EVALUATION COmpOnent-level test perFOrmed standard and /es nOn-Qml 1 M/S 2 P3 no no N/A no no no /883 Class h Qml M/S 2 yes yes yes yes yes no P3 yes yes N/A yes yes yes Element Electrical (probe) Element Visual Internal Visual Final Electrical Wire Bond Evaluation 4 yes no no no no no SLAM™/C-SAM: Input capacitors only (Add’l test, not req. by H) Notes: 1. Standard and /ES, non-QML products, do no meet all of the requirements of MIL-PRF-38534. 2. M/S = Active components (Microcircuit and Semiconductor Die) 3. P = Passive components 4. Not applicable to EMI filters that have no wire bonds. Definitions: Element Evaluation: Component testing/screening per MIL-STD-883 as determined by MIL-PRF-38534 SLAM™: Scanning Laser Acoustic Microscopy C-SAM: C - Mode Scanning Acoustic Microscopy scReenIng table 1: eleMent evaluatIOn www.interpoint.com Page 12 of 13 FMCE-1528 Rev E - 20100615 Crane Aerospace & Electronics Power Solutions FMce-1528 eMi input Filters 28 Volt input – 15 aMp STANDARD AND /ES (NON-QML) AND /883 (CLASS H, QML) PRODUCT ENVIRONMENTAL SCREENING test perFOrmed Pre-cap Inspection Method 2017, 2032 Temperature Cycle (10 times) Method 1010, Cond. C, -65°C to 150°C, ambient Method 1010, Cond. B, -55°C to 125°C, ambient Constant Acceleration Method 2001, 3000 g Method 2001, 500 g Burn-in 2 Method 1015, 125°C case, typical 96 hours 160 hours Final Electrical Test MIL-PRF-38534, Group A Subgroups 1 through 6: -55°C, +25°C, +125°C case Subgroups 1 and 4: +25°C case Hermeticity Test Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Gross Leak, Dip (1 x 10-3) Final visual inspection Method 2009 Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. Notes: 1. Standard and /ES, non-QML products, do not meet all of the requirements of MIL-PRF-38534. 2. Burn-in temperature designed to bring the case temperature to +125°C 125°C standard nOn-Qml1 yes no no no no 125°C /es nOn-Qml1 yes no yes no yes /883 Class h Qml yes yes no yes no no no no yes no no yes yes yes no no yes yes yes no yes no yes yes no yes yes no yes scReenIng table 2: envIROnMental scReenIng FMCE-1528 EMI Input Filters FMCE-1528 Rev E - 20100615. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. FMCE-1528 Series EMI Filters are a trademark of Interpoint. Copyright © 1999 - 2010 Interpoint Corporation. All rights reserved. www.interpoint.com Page 13 of 13